DOWNLOAD Sharp 28JW-73H (serv.man2) Service Manual ↓ Size: 2.38 MB | Pages: 40 in PDF or view online for FREE

Model
28JW-73H (serv.man2)
Pages
40
Size
2.38 MB
Type
PDF
Document
Service Manual
Brand
Device
TV / CTR / GA20 Chassis Training Notes
File
28jw-73h-sm2.pdf
Date

Sharp 28JW-73H (serv.man2) Service Manual ▷ View online

50Hz Widescreen Colour Television – GA20 Chassis 
 
Sharp Electronics (UK) Ltd 
Technical Support 
Issued June 02 
 
Page 4
 
 
 
This cycle will be repeated until the short circuit is removed (safe restart mode). The short winding 
protection will also protect in case of a secondary diode short circuit. 
Overcurrent 
The cycle-by-cycle peak drain current limit circuit uses the external source resistor (R715) to measure 
the current accurately. The circuit is activated after the leading edge. The Overcurrent Protection 
(OCP) circuit limits the ‘sense’ voltage to an internal level. 
Typical Voltage at pin 5 <0.56v 
Soft Start 
To prevent transformer rattle during hiccup mode, the transformer peak current is slowly increased by 
the soft start function. This is be achieved by inserting a resistor (R713) and a capacitor (C706) 
between pin 5 (I
sense
) and the sense resistor (R715). An internal current source charges the capacitor 
to a voltage that is derived from Iss X R713 to a maximum value of approximately 0.5 V. 
Drive (Pin 6) 
This is the drive to Q702 gate. the duty cycle of this signal is dependant on the conditions at the other 
pins of the TEA1507. The driver circuit to the gate of Q702 has a current sourcing capability of 
typically 125 mA and a current sink capability of typical 540 mA. This permits fast turn-on and turn-off 
of Q702 for efficient operation. This low driver source current reduces Electro Magnetic Interference 
(EMI) and also limits the current spikes across R715. 
HT
 
R
EGULATION
 
D758 is a variable zener diode. When the voltage increases on the control pin the zener point fails. 
This control pin is connected to the 150v rail via the potential divider network of R750, R751, R752 
and R753. Therefore for an increase in HT D758 turns on earlier, which in turn will turn on the opto-
coupler IC702, turning off the power supply. For a low HT then the zener point of D758 increases 
keeping IC703 turned off. 
 
IC702
D776
R744
1K
D754
R757
47K
D712
C12
D757
Q754
C753
0.27µF
D758
R742
47R
C751
1µF
R748
330K
R752
4K7
R753
47K
R751
120K
R750
120K
IC751
+5v
CTL
IN
150v
IC1001 pin 33
(Standby)
14
13
Part
of
T703
+7.5v
50Hz Widescreen Colour Television – GA20 Chassis 
 
Sharp Electronics (UK) Ltd 
Technical Support 
Issued June 02 
 
Page 5
 
 
 
S
TANDBY
 
During standby Q754 is turned on by the microprocessor which has the effect of connecting D757 and 
D712 in parallel across D758. This will keep the opto-coupler (IC702) turned on, simulating an over 
voltage condition. IC701 is now operating in burst mode. 
S
ECONDARY 
P
ROTECTION
 
In the event that a secondary supply rails fails due to excessive current or increases beyond safe 
limits then this power supply is designed to return to the burst start-up mode. 
 
Q704
D712
Q701
R717
10K
R719
10K
D706
R723
2K2
R707
150K
R703
150K
D710
C15
R725
2K7
D708
R724
10R
+350v
IC701 Pin 4
(demag)
1
2
Part
of
T703
IC702
IC701 Pin 1
(vcc)
IC701 Pin 3
(ctl)
IC703
C714
22µF
C705
22µF
 
 
This is achieved by a supply rail monitoring circuit which consisting of Q751, Q752, Q753, Q762 and 
Q759, and a control circuit consisting of IC703, Q701, D706 and D712.  
 
The  opto-coupler (IC703) is normally turned off. If it is turns on, then thyristor D706 will conduct, 
turning on Q701. Q701 emitter is connected to power supply ground and its collector is connected via 
D712 to IC701 pin 1 (VCC ). Therefore, while Q701 is turned on it is impossible for the voltage at  
IC701 pin 1  (VCC) to reach its turn on threshold, hence the power supply remains in burst mode. 
50Hz Widescreen Colour Television – GA20 Chassis 
 
Sharp Electronics (UK) Ltd 
Technical Support 
Issued June 02 
 
Page 6
 
 
 
Q751
Q752
R743
4K7
R746
4K7
R747
2K2
R758
10K
D759
D758
R749
2K2
R756
12K
Q753
R755
5K6
D761
D760
R754
18K
R766
1K
D774
Q759
D770
R765
1K8
R764
8K2
D766
R774
1K
D775
R781
1K
D773
+5v Stby
-16v
+16v
IC703
R771
15K
+5v Stby
Stby
+10V
R794
1K
Q762
D783
 C787
D784
D787
C12
D785
C6v2
    D786
R795
39K
+14v
CRT
Heaters
C774
1µF
 
Excessive EHT 
If the EHT increases then the horizontal flyback pulses will also increase. The +14v is horizontal 
flyback pulses rectified by D601, Therefore if the EHT increases then the +14v would also increase. 
The +14v is monitored by D785, C774 and R795 and applied to the base of Q762 which is normally 
turned off. When Q762 turns on it will forward bias D770, D759 and D758 causing Q752 to turn on. 
When Q752 turns on Q751 turns on, turning on the thyristor D706 via IC703, removing IC701 Vcc, 
resulting in the power supply entering burst mode. 
CRT Heater Voltage 
An increase in CRT heater voltage has a similar effect to excessive EHT, but this time the monitoring 
component is D787. 
 
50Hz Widescreen Colour Television – GA20 Chassis 
 
Sharp Electronics (UK) Ltd 
Technical Support 
Issued June 02 
 
Page 7
 
 
 
Horizontal Output Stage 
  
The horizontal output stage employed in the GA20 chassis is a conventional transformer driver circuit 
with a diode modulator for the purpose of east west correction. 
  
If the horizontal output stage develops a short circuit, the power supply will operate in burst mode. To 
confirm that it is the horizontal output stage causing burst mode operation; remove the HT feed to 
T602 by disconnecting R606. 
  
Q601
R602
220R
R601
150R
Q1006
T601
R605
5K6
R604
2K7
R607
15R
Q602
R606
3R3
D602
D603
C605
4700pF
C610
8500pF
C611
0.033µF
C608
8100pF
Scan Coils
East/West
C606
150pF
Part of T602
Fly-back TX
C602
560pF
150V
C601
1000pF
IC1001 Pin 76
H-drive
IC1001 Pin 81
H-mµte
4
1
 
  
H
ORIZONTAL 
D
RIVE 
M
UTE
 
  
Q1006 is the horizontal drive muting transistor which is controlled by the microprocessor (IC1001) pin 
81, At switch on IC1001 pin 81 is high, keeping Q1006 turned on, shorting the horizontal drive to 
ground. Once IC1001 start-up sequence is complete and it is ready to allow the horizontal stage to 
start, pin 81 will go low turning off Q1006, allowing the horizontal drive to reach the driver transistor 
Q601. 
  
If at any time the microprocessor detects a fault where it needs to stop the horizontal drive for safety 
reasons then Q1006 will be turned on again. 
H
ORIZONTAL 
O
UTPUT 
T
HEORY
 
Consider the circuit at rest, i.e. the beam spot at the centre and no current flowing through the scan 
coils. The S-correction (DC blocking) and the fly back tuning capacitor charged. 
  
Scan Coils
  
S-Correction
Fly-Back Tuning
Capacitor
Efficiency
Diode
Horizontal
Output
Direction Of Scan
 
  
Scan is initiated when the horizontal output transistor is switched on.  
  
Page of 40
Display

Click on the first or last page to see other 28JW-73H (serv.man2) service manuals if exist.