DOWNLOAD Sharp XV-Z3000 (serv.man2) Service Manual ↓ Size: 3.34 MB | Pages: 67 in PDF or view online for FREE

Printed in China
Gedruckt in China
Imprimé en Chine
Triykt i Kina
Impreso en China
Stampato in Cina
Gedrukt in China
TINS-C222WJN1
06P02-CH-NG

XV-Z3000_EN__cover

06.2.9, 10:57 AM

1

SPECIAL NOTE FOR USERS IN THE U.K.
The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporat-
ing a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362
fuse marked   or 

 and of the same rating as above, which is also indicated on the pin

face of the plug, must be used.
Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse
cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug
supplied, cut off the mains plug and fit an appropriate type.

DANGER:
The fuse from the cut-off plug should be removed and the cut-off plug destroyed immedi-
ately and disposed of in a safe manner.
Under no circumstances should the cut-off plug be inserted elsewhere into a 13A socket
outlet, as a serious electric shock may occur.
To fit an appropriate plug to the mains lead, follow the instructions below:

WARNING:
THIS APPARATUS MUST BE EARTHED.
IMPORTANT:
The wires in this mains lead are coloured in accordance with the following code:

Green-and-yellow : Earth
Blue

: Neutral

Brown

: Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the
coloured markings identifying the terminals in your plug proceed as follows:

•

The wire which is coloured green-and-yellow must be connected to the terminal in the
plug which is marked by the letter E or by the safety earth symbol 

 or coloured green or

green-and-yellow.

•

The wire which is coloured blue must be connected to the terminal which is marked with
the letter N or coloured black.

•

The wire which is coloured brown must be connected to the terminal which is marked with
the letter L or coloured red.

IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.

XV-Z3000_EN_a

06.1.10, 2:54 PM

3

High brightness light source. Do not stare into the beam of light, or view
directly. Be especially careful that children do not stare directly into the
beam of light.

To reduce the risk of fire or electric shock, do not expose
this product to rain or moisture.

The lightning flash with arrowhead sym-
bol, within an equilateral triangle, is in-
tended to alert the user to the presence
of uninsulated “dangerous voltage”
within the product’s enclosure that may
be of sufficient magnitude to constitute
a risk or electric shock to persons.

The exclamation point within a triangle
is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in
the literature accompanying the product.

See bottom of projector.

• For your assistance in reporting the loss

or theft of your Projector, please record
the Serial Number located on the bottom
of the projector and retain this information.

• Before recycling the packaging, please

ensure that you have checked the con-
tents of the carton thoroughly against the
list of “Supplied accessories” on page 10.

XV-Z3000_EN_b

06.1.10, 3:08 PM

1

The cooling fan in this projector continues to run for about 90 seconds after the projector enters
standby mode. During normal operation, when putting the projector into standby mode always
use the STANDBY/ON button on the projector or the STANDBY button on the remote control.
Ensure the cooling fan has stopped before disconnecting the power cord.
DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING
THE POWER CORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.

See “Replacing the Lamp” on page 54.

This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of
mercury. Disposal of these materials may be regulated due to environmental considerations.
For disposal or recycling information, please contact your local authorities or, if you are
located in the United States of America, the Electronic Industries Alliance: www.eiae.org .

This SHARP projector uses a DMD panel. This very sophisticated panel contains 983,040 pixels
(micromirrors). As with any high technology electronic equipment such as large screen TVs,
video systems and video cameras, there are certain acceptable tolerances that the equipment
must conform to.
This unit has some inactive pixels within acceptable tolerances which may result in inactive dots
on the picture screen. This will not affect the picture quality or the life expectancy of the unit.

XV-Z3000_EN_b

06.1.10, 3:08 PM

2