Sharp XV-Z201E (serv.man31) User Manual / Operation Manual ▷ View online
-8
Projector (Front and Top View)
30
58
58
POWER indicator
6
Exhaust ventilative hole
LAMP indicator
TEMPERATURE
WARNING indicator
WARNING indicator
39
ADJUSTMENT buttons
(ƒ/∂/ß/©)
39
UNDO button
38
MENU button
35
RESIZE button
31
INPUT button
24
Swivel Stand
LOCK/UNLOCK lever
LOCK/UNLOCK lever
11
Remote control sensor
Lens cap
Zoom knob
25
Exhaust ventilative hole
6
Focus ring
25
25
Lens shift dial
39
ENTER button
33
KEYSTONE button
ON button
30
STANDBY
button
button
32
47
PICTURE SETTING button
Attaching the Lens Cap
The lens cap can be attached to the
projector using commercially
available straps (for cellular phones
etc.), as shown in the figure.
The lens cap can be attached to the
projector using commercially
available straps (for cellular phones
etc.), as shown in the figure.
Projector (Side and Rear View)
Numbers in
refer to the main pages in this operation manual where the topic is explained.
Part Names
XV_Z201E_E_p04_12.p65
03.10.30, 12:16AM
8
Introduction
-9
Projector (Rear View)
Using the Terminal Cover
When the projector is used on a desktop, high mounted or ceiling mounted, attach the terminal cover (supplied)
to hide the connecting cables.
When the projector is used on a desktop, high mounted or ceiling mounted, attach the terminal cover (supplied)
to hide the connecting cables.
17
16
62
Intake ventilative hole
AC socket
Intake ventilative hole
62
18
INPUT 2/DIGITAL INPUT
terminal
INPUT 1 COMPONENT
terminals (RCA)
INPUT 4 VIDEO terminal (RCA)
20
DIGITAL INPUT
TYPE switch
TYPE switch
15
INPUT 3 S-VIDEO terminal
(4-pin Mini DIN)
23
RS-232C terminal
(9-pin D-sub)
(9-pin D-sub)
11
Remote control sensor
14
Attaching the Terminal
Cover
1 Align with the tabs on
Cover
1 Align with the tabs on
the projector and
then press the
terminal cover in the
direction of the arrow.
then press the
terminal cover in the
direction of the arrow.
2 Tighten the two
screws on the bottom
of the projector.
of the projector.
Removing the Terminal
Cover
1 Loosen the two screws
Cover
1 Loosen the two screws
on the bottom of the
projector.
projector.
2 Raise the terminal cover
and pull it out in the
direction of the arrow.
direction of the arrow.
2 Tighten the screws
1 Loosen the screws
1
2
XV_Z201E_E_p04_12.p65
03.10.30, 12:16AM
9
-10
Part Names
Remote Control (Front View)
Remote Control (Top View)
FREEZE button
32
31
50
52
39
39
38
39
31
31
31
31
35
47
35
STANDBY button
ENTER button
33
KEYSTONE button
UNDO button
INPUT 1 button
INPUT 2 button
INPUT 4 button
AUTO SYNC button
RESIZE button
PICTURE SETTING button
MENU button
30
ON button
ADJUSTMENT buttons
(ƒ/∂/ß/©)
(ƒ/∂/ß/©)
INPUT 3 button
DIGITAL INPUT button
RGB/COMP. button
Remote control signal transmitters
XV_Z201E_E_p04_12.p65
03.10.30, 12:16AM
10
Introduction
-11
Operating the Remote Control
■ The remote control can be used to control the projector
within the ranges shown in the illustration.
Note
• The signal from the remote control can be reflected off a screen
for easy operation. However, the effective distance of the signal
may differ due to the screen material.
may differ due to the screen material.
When using the remote control:
• Be sure not to drop, or expose to moisture or high temperature.
• The remote control may malfunction under a fluorescent lamp.
Under that circumstance, move the projector away from the fluo-
rescent lamp.
rescent lamp.
Available Range of the Remote Control
Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below.
Caution
• Insert the batteries making sure the polarities correctly match the and marks inside the battery compart-
ment.
• Batteries of different types have different properties, therefore do not mix batteries of different types.
• Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
• Remove the batteries from the remote control once they have run out, as leaving them can cause them to leak.
Battery fluid from leaked batteries is harmful to your skin, therefore be sure to first wipe them and then remove
them using a cloth.
them using a cloth.
• The batteries included with this projector may exhaust over a short period, depending on how they are kept.
Be sure to replace them as soon as possible with new batteries when they have run out.
• Remove the batteries from the remote control if you will not be using the remote control for a long time.
Inserting the Batteries
The batteries (two “AA” size) are included in
the package.
the package.
1
Pull down the tab on the cover
and remove the cover towards
the direction of the arrow.
and remove the cover towards
the direction of the arrow.
2
Insert the included batteries.
• Insert the batteries making sure the
polarities correctly match the
and
marks inside the battery compart-
ment.
3
Insert the lower tab of the
cover into the opening, and
lower the cover until it clicks
in place.
cover into the opening, and
lower the cover until it clicks
in place.
Remote control
Remote control
45˚
7 m
30˚
30˚
45˚
30˚
XV_Z201E_E_p04_12.p65
03.10.30, 12:16AM
11
Click on the first or last page to see other XV-Z201E (serv.man31) service manuals if exist.