DOWNLOAD Sharp XV-Z2000E (serv.man16) Service Manual ↓ Size: 127 KB | Pages: 2 in PDF or view online for FREE

Model
XV-Z2000E (serv.man16)
Pages
2 Few pages! See other manuals at the bottom of the first or last page.
Size
127 KB
Type
PDF
Document
Service Manual
Brand
Device
Projector / XV-Z2000 p23-24 Resetting the lamp timer
File
xv-z2000e-sm16.pdf
Date

Sharp XV-Z2000E (serv.man16) Service Manual ▷ View online

23
XV-Z2000
DT-400
RESETTING THE TOTAL LAMP TIMER
Resetting the total lamp timer
When replacing the lamp, reset the total lamp timer in the procedure below.
The warning lights (ON/STANDBY button, lamp indicator and temperature warning indicator) on the projector
indicate problems inside the projector.
If a problem occurs, either the temperature warning indicator or the lamp indicator will illuminate red, and the
projector will enter the standby mode. After the projector has entered the standby mode, follow the procedures
given below.
Lamp
It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes 5% or less,
or when you notice a significant deterioration in the picture and color quality. The lamp life (percentage) can be
checked with the on-screen display.
Purchase a replacement lamp of type AN-K2LP from your place of purchase, nearest Sharp Projector Dealer or
Service Center.
Power indicator
Lamp indicator
Temperature warning indicator
Maintenance Indicators
About the temperature warning indicator
If the temperature inside the projector increases, due to blockage of the air vents, or the setting location,
” will illuminate in the lower left corner of the picture. If the temperature keeps on rising, the lamp will
turn off and the temperature warning indicator will blink, the cooling fan will run for a further 90 seconds, and
then the projector will enter the standby mode. After “
” appears, ensure to perform the measures
described on operation manual.
Info
Make sure to reset the lamp timer only
when replacing the lamp. If you reset the
lamp timer and continue to use the same
lamp, this may cause the lamp to become
damaged or explode.
1
Connect the power cord.
Plug the power cord into the AC socket
of the projector.
2
Reset the lamp timer.
Press
,
,
,
\
\
\
\
\
,
and
|
|
|
|
|
on the
projector in order, and then press 
on
the projector.
“LAMP 0000H” is displayed on the lower
left of the screen, indicating that the lamp
timer is reset.
AC socket
\
/
|
 buttons
ON button
ENTER button
UNDO button
INPUT button
24
XV-Z2000
DT-400
Maintenance indicator
Problem
Cause
Possible solution
Temperature
warning
indicator
Normal
Abnormal
Off
Red on
(Standby)
The internal
temperature is
abnormally high.
Abnormal
 Blocked air intake
Relocate the projector to an area
with proper ventilation
Cooling fan break-
down
Internal circuit failure
Clogged air intake
Take the projector to your nearest
Sharp Authorized Projector Dealer
or Service Center for repair.
Clean the exhaust and intake
vents.
Lamp
indicator
Red on
(Standby)
The lamp does
not illuminate.
Burnt-out lamp
Lamp circuit failure
Carefully replace the lamp.
Take the projector to your nearest
Sharp Authorized Projector Dealer
or Service Centerfor repair.
Please exercise care when
replacing the lamp.
Red on
Time to change
the lamp.
Remaining lamp life
becomes 5% or less.
Green on
Green blinks
when the lamp
is warming up
or shutting
down.
Info
If the temperature warning indicator illuminates and the projector enters the standby mode, check whether
any of the ventilation holes are blocked and then try turning the power back on. Wait until the projector has
cooled down completely before plugging in the power cord and turning the power back on.
(At least 10 minutes.)
If the power is turned off for a brief moment due to power outage or some other cause while using the
projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red
and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power
cord in the AC outlet and then turn the power on again.
Do not unplug the power cord after the projector has entered the standby mode and while the cooling fan
is running. The cooling fan runs for about 90 seconds.
The lamp does
not illuminate.
The lamp is shut
down abnormally.
Disconnect the power cord from
the AC outlet, and then connect it
again.
Display

Sharp XV-Z2000E (serv.man16) Service Manual ▷ Download

  • DOWNLOAD Sharp XV-Z2000E (serv.man16) Service Manual ↓ Size: 127 KB | Pages: 2 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sharp XV-Z2000E (serv.man16) in PDF for free, which will help you to disassemble, recover, fix and repair Sharp XV-Z2000E (serv.man16) Projector. Information contained in Sharp XV-Z2000E (serv.man16) Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.