DOWNLOAD Sharp XV-Z2000E (serv.man14) Service Manual ↓ Size: 95.2 KB | Pages: 7 in PDF or view online for FREE

Model
XV-Z2000E (serv.man14)
Pages
7
Size
95.2 KB
Type
PDF
Document
Service Manual
Brand
Device
Projector / XV-Z2000 p27-33 electrical adjustmenrs
File
xv-z2000e-sm14.pdf
Date

Sharp XV-Z2000E (serv.man14) Service Manual ▷ View online

30
XV-Z2000
DT-400
13
DVD White
balance
(Auto
adjustment)
1. Feed the component 75%
gray scale signal.
2. Group: PIXEL
Subject:R-GAIN (R)
             B-GAIN (B)
             Input 5 Color
             difference input
1. Adjust the white balance by controlling R-GAIN and
B-GAIN.
(Adjust x=298 and y=319.)
1. Make the following settings.
Destination
Process adjustment Remote controller setting
Europe
SS3
Factory setting 3
North America
SS4
Factory setting 4
15
Factory setting
14
DLP voltage
adjustment
1. Read the DLP-listed volt-
age rank.
2. Make the switch setting
corresponding to the read-
out rank.
(on the Formatter PWB)
1. Make this adjustment when the DLP chip has been
replaced or the combination of DLP chip and
Formatter PWB has been changed.
1.  Ranking: D  E
No.
Adjusting point
Adjusting conditions
Adjusting procedure
30
31
XV-Z2000
DT-400
*1272-6bbc
CHXXXX
LLLLL
YYYYYYY
L LLL LM
TI Intemal Numbering
TI Intemal Numbering
2-Dimensional Matrix Code
(DMD Part Number and
Serial Number)
Part 1 of Serial Number
(7 characters)
Part 2 of Serial Number
(6 or 7 characters)
DMD Part Number
The last alphabet letter indicates the
Bin voltage setting (D. E).
1
* Precautions in setting up the DMD (Digital Micromirror Device) unit
Before connecting the formatter PWB to the optical engine, take the following steps. Look at the voltage rank marking
that is on the DMD itself. Referring to this marking, set the DIP switches on the formatter PWB. And connect this PWB
to the optical engine. Wrong settings will adversely affect the system performance.
Set the formatter PWB switches according to the Bin voltage shown on the back face of the DMD.
2
Based on Bin voltage, switch is set up as follows.
D:
E:
32
XV-Z2000
DT-400
Calling and quitting the process mode with the control keys on this model.
Although it is possible for the process OUT to exit using the process menu, the IN/OUT toggle command is also
available considering the existing specification.
1. Calling and quitting
With the menu not displayed, press the "
'
", "
'
", "
"
", "
"
", "
|
", "
\
" and "ENTER" keys on main unit.
2. Others
Press the S2002 process key (toggle) on the main PWB to call and quit the process menu.
Note: When adjusting in the process mode, set a signal with a vertical frequency of 60 Hz or no signal. (May not be
properly adjusted with other signals.)
»
 Adjustment mode process menu
Adjustment mode process menu 1
* Adjust only the shaded items below.
Adjustment Process Menu
First layer
DTV
VERSION
DVD
SS
VIDEO
TEMP
AD
OPTION
DLP
PATTERN
VIDEO1
LAMP
PIXEL
LINE
Pedestal
EXIT
second layer
Initial Value
DTV
Contrast
5
Tint
8
Color
4
Sharpness
1
Bright
55
R-Bright
20
G-Bright
20
B-Bright
20
R-Contrast
120
G-Contrast
120
B-Contrast
120
EXIT
DVD
Contrast
5
Tint
4
Color
5
Sharpness
1
CTi-Level
1
LTi-Level
0
CB-Offset
7
CR-Offset
7
Bright
55
B-DRIVE
41
R-DRIVE
41
EXIT
VIDEO
Contrast
5
N-Tint
7
P-Tint
4
S-Tint
4
N-Color
7
P-Color
4
S-Color
7
Sharpness
2
CTi-Level
1
LTi-Level
0
CB-Offset
7
CR-Offset
7
Bright
55
B-DRIVE
41
R-DRIVE
41
EXIT
33
XV-Z2000
DT-400
Adjustment mode process menu 2
second layer
Initial Value
VERSION
Build
Boot Code
Config
RomCode
GUI
DLP
EXIT
SS
SS2
SS3 EU
SS4 US
SS5 JPN
SS6 CHIN
EXIT
TEMP
Temp1
Parameter of sensor1
Temp2
Parameter of sensor2
Temp3
Temp4
EXIT
OPTION
PW365 Gamma Standard VIDEO
DLP Gamma
8
EXIT
PATTERN
Cross Hatch
Color bar
EXIT
LAMP
Current Time
Current time of use
History1
One Earlier
History2
Two Earlier
History3
Three Earlier
History4
Four Earlier
TOTAL TIME
Total operating hours
EXIT
LINE
OFF
LED CHECK
EXIT
second layer
Initial Value
AD
R-Bright
40
G-Bright
40
B-Bright
40
R-Contrast
120
G-Contrast
120
B-Contrast
120
EXIT
DLP
Index Delay
325
R-Bright
128
G-Bright
128
B-Bright
128
R-Contrast
100
G-Contrast
100
B-Contrast
100
EXIT
VIDEO1
N-Contrast
14
P-Contrast
14
S-Contrast
15
Color
17
NT3.58Delay
0
NT4.43Delay
1
PAL Delay
5
SECAM Delay 0
Shapness2
1
EXIT
PIXEL
R-GAIN
128
G-GAIN
128
B-GAIN
128
EXIT
Pedestal
R-Bright
-10
G-Bright
-10
B-Bright
-10
R-Contrast
+10
G-Contrast
+10
B-Contrast
+10
EXIT
Page of 7
Display

Sharp XV-Z2000E (serv.man14) Service Manual ▷ Download

  • DOWNLOAD Sharp XV-Z2000E (serv.man14) Service Manual ↓ Size: 95.2 KB | Pages: 7 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sharp XV-Z2000E (serv.man14) in PDF for free, which will help you to disassemble, recover, fix and repair Sharp XV-Z2000E (serv.man14) Projector. Information contained in Sharp XV-Z2000E (serv.man14) Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.