Sharp XV-Z10E (serv.man29) Service Manual / Technical Bulletin ▷ View online
PJR 2005 06 02
Date of Issue: 24
th
June 2005
Classification:
White
PROJECTOR TECHNICAL BULLETIN
Page 1 of 4
Sharp Electronics (UK) Limited
Reference - LP-006
Revision - 1
White – Carry out as required
Yellow – Carry out as required and whenever the unit comes in for service
Red – Carry out on all units
MODEL
XVZ10E
SYMPTOM Lamp may not light, even if ignition is tried several times.
CAUSE
Software.
ACTION
Upgrade the software to REL111 as described below.
1. Connect the projector and the PC via a RS232 cross connection cable.
2. Turn the projector on.
3. Enter the factory mode (with the menu not displayed, press, up, up, down, down,
2. Turn the projector on.
3. Enter the factory mode (with the menu not displayed, press, up, up, down, down,
right, left and enter buttons in sequence). If you have the service remote control,
this can be used to enter the service mode
this can be used to enter the service mode
4. The menu shown below will now appear.
5. Select VERSON and press the enter button. Note down the version number.
6. Exit this screen and select and note the following data:
6. Exit this screen and select and note the following data:
7. Turn the projector off and disconnect the mains lead.
PJR 2005 06 02
Date of Issue: 24
th
June 2005
Classification:
White
PROJECTOR TECHNICAL BULLETIN
Page 2 of 4
Sharp Electronics (UK) Limited
Reference - LP-006
Revision - 1
White – Carry out as required
Yellow – Carry out as required and whenever the unit comes in for service
Red – Carry out on all units
Rewriting the software:
1. Unzip the file Z10-V111.zip (this can be found on the Sharp Technical Web under
this model) to a suitable directory on your computers hard drive.
2. Double click on the "FlashUpgrader.exe" file. The window shown below will
appear.
3. Click on the choose button.
4. Select folder Z10-111. Then select file pwSDK.inf
4. Select folder Z10-111. Then select file pwSDK.inf
5. Make sure that Continueous Flash mode and Notify on Completion are unchecked.
6. Make sure that Reset Target After Download is checked.
7. Make sure that Flash is selected in Modes.
6. Make sure that Reset Target After Download is checked.
7. Make sure that Flash is selected in Modes.
8. Click on the Flash button.
PJR 2005 06 02
Date of Issue: 24
th
June 2005
Classification:
White
PROJECTOR TECHNICAL BULLETIN
Page 3 of 4
Sharp Electronics (UK) Limited
Reference - LP-006
Revision - 1
White – Carry out as required
Yellow – Carry out as required and whenever the unit comes in for service
Red – Carry out on all units
9. Connect the mains lead to the projector and turn it on - software re-writing will start
automatically.
10. When writing is complete the window below will appear.
11. Click close.
Setting up after rewritting
After rewriting the software, it will be necessary to reset the language, eco mode etc.
1. Connect the projector and the PC via a RS232 cross connection cable.
2. Turn the projector on.
3. Enter the factory mode (with the menu not displayed, press, up, up, down, down,
2. Turn the projector on.
3. Enter the factory mode (with the menu not displayed, press, up, up, down, down,
right, left and enter buttons in sequence).
4. Reset data as noted down previously.
5. Select VERSION and press the enter key.
6. Check that the factory data has updated:
5. Select VERSION and press the enter key.
6. Check that the factory data has updated:
PJR 2005 06 02
Date of Issue: 24
th
June 2005
Classification:
White
PROJECTOR TECHNICAL BULLETIN
Page 4 of 4
Sharp Electronics (UK) Limited
Reference - LP-006
Revision - 1
White – Carry out as required
Yellow – Carry out as required and whenever the unit comes in for service
Red – Carry out on all units
7. Exit this screen and select SS.
8. Select SS2 and press enter.
8. Select SS2 and press enter.
9. Check that the data noted down at the start of this procedure is the same.
10. Goto SS again and select SS
3 EU and press enter.
11. Exit menu.
12. Set-up is now complete.
12. Set-up is now complete.
Display
