DOWNLOAD Sharp XG-V10XE (serv.man8) Service Manual ↓ Size: 1.22 MB | Pages: 19 in PDF or view online for FREE

In the interests of user-safety (Required by safety regulations in some countries) the set should be restored
to its original condition and only parts identical to those specified should be used.

Im lnteresse der Benutzersicherheit (erforderliche Sicherheitsregeln in einigen Ländern) muß das Gerät in seinen
Originalzustand  gebracht werden.  Außerdem dürfen für die spezifizierten Bauteile nur identische Teile verwendet
werden.

S11N8XG-V10XE

• SPECIFICATIONS ............................................. 3

• NOTE TO SERVICE PERSONNEL ................... 4

• OPERATION MANUAL ...................................... 6

• REMOVING OF MAJOR PARTS ..................... 14

• RESETTING THE TOTAL LAMP TIMER ......... 19

• THE OPTICAL UNIT OUTLINE ........................ 20

• CONVERGENCE AND

 FOCUS ADJUSTMENT .................................. 21

• ELECTRICAL ADJUSTMENT .......................... 27

• ADJUSTING THE PC INTERFACE ................. 35

• TROUBLE SHOOTING TABLE ........................ 39

• CHASSIS LAYOUT ......................................... 118

• BLOCK DIAGRAM ......................................... 120

Page

Page

• OVERALL WIRING DIAGRAM ...................... 122

• DESCRIPTION OF SCHEMATIC DIAGRAM . 124

• WAVEFORMS ................................................ 125

• SCHEMATIC DIAGRAM ................................ 126

• PRINTED WIRING BOARD ASSEMBLIES ... 184

• PARTS LIST

Ë

ELECTRICAL PARTS ............................... 197

Ë

CABINET AND MECHANICAL PARTS .... 231

Ë

ACCESSORIES PARTS ........................... 236

Ë

PACKING PARTS ..................................... 236

• PACKING OF THE SET ................................. 237

• TECHNISCHE DATEN ..................................... 60

• HINWEISE FÜR DAS

WARTUNGSPERSONAL ................................. 61

• BEDIENUNGSANLEITUNG ............................. 63

• ENTFERNEN DER HAUPTTEILE ................... 71

• RÜCKSTELLEN DES LAMPEN-BETRIEBS-

ZEITZÄHLERS ................................................. 76

• ÜBERSICHT DER OPTIKEINHEIT .................. 77

• EINSTELLUNG VON KONVERGENZ UND

BRENNPUNKT ................................................ 78

• ELEKTRISCHE EINSTELLUNG ...................... 84

• EINSTELLUNG DER PC-PLATINE .................. 92

• FEHLERSUCHTABELLE ................................. 96

• CHASSIS-ANORDNUNG ............................... 118

Seite

Seite

• BLOCKSCHALTBILD ..................................... 120

• GESAMTSCHALTPLAN ................................. 122

• BESCHREIBUNG DES SCHEMATISCHEN

SCHALTPLANS ............................................. 124

• WELLENFORMEN ......................................... 125

• SCHEMATISCHER SCHALTPLAN ................ 126

• LEITERPLATTENEINHEITEN ....................... 184

• ERSATZTEILLISTE

Ë

ELEKTRISCHE BAUTEILE ...................... 197

Ë

CEHÄUSE UND MECHANISCHE

BAUTEILE ................................................ 231

Ë

ZUBEHÖRTEILE ...................................... 236

Ë

VERPACKUNGSTEILE ............................ 236

• VERPACKEN DES GERÄTS ......................... 237

Product type

LCD Projector

Model

XG-V10XE

Video system

PAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSC 4.43
DTV 480i/480P/720P/1080i

Display method

LCD panel x 3, RGB optical shutter method

LCD panel

Panel size:46 mm (1.8" ) (27.6 [H] x 36.9 [W] mm))
Display method:Translucent TN liquid crystal panel
Drive method:TFT (Thin Film Transistor)Active Matrix panel
No.of dots:786,432 dots (1,024 [H] x 768 [V])

Projection lamp

200 W UHP lamp x 2

Contrast ratio

400:1

Video input signal

BNC Connector:VIDEO (INPUT 4, 5), composite video,1.0 Vp-p,sync negative, 75 

Ω

 terminated

RCA Connector:AUDIO (INPUT 4,5),0.5 Vrms more than 22 k

Ω

 (stereo)

S-video input signal

4-pin Mini DIN connector (INPUT 4,5)
Y (luminance signal):1.0 Vp-p,sync negative, 75 

Ω

 terminated

C (chrominance signal):Burst 0.286 Vp-p, 75 

Ω

 terminated

Component input signal

BNC Connector (INPUT 2, 4, 5)
Y:1.0 Vp-p,sync negative,75 

Ω

 terminated

P

B

:0.7 Vp-p,75 

Ω

 terminated

P

R

:0.7 Vp-p,75 

Ω

 terminated

Horizontal resolution

620 TV lines (S-video input),650 TV lines (DTV 720P input,STRETCH mode)

RGB input signal

15-PIN MINI D-SUB CONNECTOR (INPUT 1), 5 BNC CONNECTOR (INPUT 2):

RGB separate/composite sync/sync on green type analog input:0 –0.7 Vp-p, positive,
75  terminated

DVI CONNECTOR (29-PIN) (INPUT 3), RGB (DIGITAL),250 –1,000 mV, 50 

Ω

H

ORIZONTAL SYNC.SIGNAL:

TTL level (positive/negative) or composite sync (Apple only)

V

ERTICAL SYNC.SIGNAL:

Same as above

Pixel clock

12 –230 MHz

Vertical frequency

43 –200 Hz

Horizontal frequency

15 –126 kHz

Computer control signal

9-pin D-sub connector (RS-232C Input Port/Output Port)

Speaker system

5 x 8 cm (1 

31

⁄

32

" x 3  

5

⁄

32

" ) oval 2, 3 W + 3 W (stereo)

Rated voltage

AC 110 –120/220 –240 V

Input current

6.2 A/3.1 A

Rated frequency

50/60 Hz

Power consumption

575 W

Power dissipation

<2,100 BTU/hour

Operating temperature

+ 5 

°

C to + 40 

°

C

Storage temperature

– 20 

°

C to + 60 

°

C

Cabinet

Plastic

I/R carrier frequency

38 kHz

Laser pointer of remote control

Wave length:650 nm /Max.output:1 mW /Class II Laser Product

Dimensions (approx.)

444.2 x 196.2 x 621.3 mm (W x H x D) (main body only)
530.1 x 221.9 x 643.2 mm (W x H x D) (including standard lens, terminal cover, adjustment feet
and projecting parts)

Weight (approx.)

18.9 kg (main body only)

Supplied accessories

Remote control, Two AA size batteries, Power cord (1.8 m), RGB cable (3 m), PS/2 mouse control
cable (1 m), USB mouse control cable (1 m), Remote mouse receiver, Extra air filter, Terminal
cover, CD-ROM, LCD projector operation manual, LCD projector quick references, Sharp Advanced
Presentation Software operation manual

Replacement parts

Lamp unit (Lamp/cage module)(BQC-XGV10WU/1),Remote control (RRMCG1565CESA), AA size
batteries,Power cord,RGB cable (QCNW-5304CEZZ),PS/2 mouse control cable (QCNW-
5113CEZZ),USB mouse control cable (QCNW-5680CEZZ),Remote mouse receiver
(RUNTK0673CEZZ),Air filter (PFILD0110CEZZ),Terminal cover (CCOVA1789CE01),CD-ROM
(UDSKA0038CEN1),LCD projector operation manual (TINS- 7277CEZZ),LCD projector quick ref-
erences (TINS-7278CEZZ,TINS-7279CEZZ,TINS- 7280CEZZ),Sharp Advanced Presentation
Software operation manual (TINS-7281CEZZ)

This SHARP projector uses LCD (Liquid Crystal Display)
panels.These very sophisticated panels contain 786,432 pixels ( x
RGB) TFTs (Thin Film Transistors). As with any hig technology elec-
tronic equipment such as large screen TVs,video systems and video
cameras,there are certain acceptable tolerances that the equipment
must conform to.

This unit has some inactive TFTs within acceptable tolerances which
may result in illuminated or inactive dots on the picture screen.This
will not affect the picture quality or the life expectancy of the unit.

Specifications are subject to change without notice.

12345678901234567890123456789012123456789012345

12345678901234567890123456789012123456789012345

12345678901234567890123456789012123456789012345

1234567890123456789012345678901212345678901234

1234567890123456789012345678901212345678901234

1234567890123456789012345678901212345678901234

1

2

Lamp

Reflector

Since small amounts of UV-radiation are emitted from
an opening between the exhaust fans, it is recom-
mended to place the cap of the optional lens on the
opening during servicing to avoid eye and skin ex-

posure (Fig. 1).

Note: Please obtain a lens cap before servicing a

model XG-V10XE that is received without
one.

DANGER !  –– Never turn the power on without the
lamp to avoid electric-shock or damage of the
devices since the stabilizer generates high voltages
at its start.

Since the lamp reaches a very high temperature
during units operation replacement of the lamp
should be done at least one hour after the power
has been turned off.  (to allow the lamp to cool off.)
Installing the new lamp, make sure not to touch the
lamp (bulb) replace the lamp by holding its reflector

2

.

[Use original replacement only.]

LENS CAP

1. Be sure to wear sun-glasses when servicing the

projector with the lamp
turned “on” and the top
enclosure removed.

2. Do not operate the lamp outside of the lamp housing.

3. Do not operate for more than 2 hours with the

enclosure removed.

1. Be sure to disconnect the AC plug when replacing

the lamp.

2. Allow one hour for the unit to cool down before

servicing.

3. Replace only with same type lamp. Type

CLMPF0064DE01/02 or BQC-XGV10WU/1 rated
100V/200W.

4. The lamp emits small amounts of UV-Radiation,  avoid

direct-eye contact.

5. The medium pressure lamp involves a risk of

explosion. Be sure to follow installation instructions
described below and handle the lamp with care.

12345678901234567890123456789012123456789012345

12345678901234567890123456789012123456789012345

12345678901234567890123456789012123456789012345

12345678901234567890123456789012123456789012345