DOWNLOAD Sharp XG-V10XE (serv.man29) Service Manual ↓ Size: 637.71 KB | Pages: 6 in PDF or view online for FREE

Model
XG-V10XE (serv.man29)
Pages
6
Size
637.71 KB
Type
PDF
Document
User Manual / Operation Manual
Brand
Device
Projector / - Useful Features Network Functions
File
xg-v10xe-sm29.pdf
Date

Sharp XG-V10XE (serv.man29) User Manual / Operation Manual ▷ View online

69
Maintenance &
Tr
oubleshooting
TEMP
LAMP2
LAMP1 POWER
2
1
Lamp/Maintenance Indicators
Problem
• Blocked air intake.
• Clogged air filter.
• Cooling fan breakdown.
• Internal circuit failure.
• Burnt-out lamp.
• Lamp circuit failure.
• Lamp has been used for
over 900 hours.
• The filter cover is open.
• The lens cover* is not
securely installed.
Maintenance Indicator
The internal
temperature is
abnormally high.
TEMPERATURE
WARNING indicator
LAMP REPLACE-
MENT indicator
POWER indicator
The lamp does not
light up.
The lamp requires
replacement.
The POWER
indicator flashes in
red when the
projector is on.
Condition
Possible Solution
• Relocate the projector to an area with
proper ventilation.
• Replace the filter.
(See page 73.)
• Take the projector to your nearest Sharp
Authorised LCD Projector Dealer or Service
Centre for repair.
• Carefully replace the lamp. (See pages 71
and 72.)
• Take the projector to your nearest Sharp
Authorised LCD Projector Dealer or Service
Centre for repair.
• Securely install the filter cover.
• Securely install the lens cover.
Maintenance Indicators
• The warning lights on the projector indicate problems
inside the projector.
• There are three warning lights: a TEMPERATURE
WARNING indicator that warns you when the projector
is too hot, and two LAMP REPLACEMENT indicators
that warn you when to change a lamp.
• If a problem occurs, either the TEMPERATURE
WARNING indicator or the LAMP REPLACEMENT
indicators will light up red. After turning off the power,
follow the procedures given below.
LAMP 2
REPLACEMENT
indicator
TEMPERATURE
WARNING
indicator
LAMP 1
REPLACEMENT
indicator
POWER
indicator
* The lens cover is as shown below.
Lens cover
• If the TEMPERATURE WARNING indicator lights up, follow the above possible solutions and then wait until the projector has
cooled down completely before turning the power back on. (At least 5 minutes.)
• If the power is turned off and then turned on again, as during a brief rest, the LAMP REPLACEMENT indicators may be
triggered, preventing the power from going on. Should this occur, take the power cord out of the wall outlet and put it back
in again.
70
Maintenance &
Tr
oubleshooting
Confirming the Lamp Usage Time
Lamp Maintenance
Lamp
The lamp in this projector operates for approximately 1,000 cumulative hours, depending on the usage environ-
ment. (As the usage environment can vary significantly, the projector lamp may not operate for 1,000 hours.) It is
recommended that the lamp be replaced after approximately 900 cumulative hours of use or when you notice a
significant deterioration of the picture and colour quality. The lamp usage time can be checked with the On-screen
Display.
CAUTION
• Intense light hazard. Do not attempt to look into the aperture and lens while the projector is operating.
This function allows you to check the accumulated lamp
usage time.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1 Press MENU.
2 Press ß/© to select “Options (2)”.
3 Press  ∂/ƒ to select “Lamp Timer”. The lamp
usage time will be displayed.
4 To exit from the GUI, press MENU.
• It is recommended that the lamp be replaced after
approximately 900 cumulative hours of use. See pages 71
and 72 for lamp replacement.
1.2.3
4.5.6
14
23
Projector
MOUSE
ADJ.
Remote Control
(GUI) On-screen Display
Problem
• Lamp has been used for over 900
hours.
• Lamp has been used for over 1,000
hours.
Possible Solution
• Purchase a replacement lamp unit
(lamp/cage module) of the current
type BQC-XGV10WU/1 from your
nearest Sharp Authorised LCD
Projector Dealer or Service Centre.
• Replace the lamp. (See pages 71
and 72.) If you wish, you may have
the lamp replaced at your nearest
Sharp Authorised LCD Projector
Dealer or Service Centre.
Condition
The LAMP REPLACEMENT
indicator lights up red, and “LAMP”
and “ ” will flash in yellow in the
lower-left corner of the picture.
A significant deterioration of the
picture and colour quality occurs.
The power will automatically turn
off and the projector will enter
standby mode.
“LAMP” and “ ” will flash in red in
the lower-left corner of the picture,
and the power will turn off.
71
Maintenance &
Tr
oubleshooting
This function can be used to set the lamp mode.
The mode can be set to double the effective lamp usage
time.
Description of Lamp Mode
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
1 Press MENU.
2 Press ß/© to select “Options (2)”.
3 Press ∂/ƒ to select “Lamp Mode”, and then
press ©.
4 Press ∂/ƒ to select the desired Lamp Mode.
5 Press ENTER to save the setting.
6 To exit from the GUI, press MENU.
• In “Equal Use” mode, when the projector is used for more than
24 hrs. continuously, it switches in shift of 100 hrs.
Setting the 
Lamp Mode
1.2.3
4.5.6
16
5
234
Remote Control
Projector
(GUI) On-screen Display
Selected item
Both Lamps
Lamp 1 Only
Lamp 2 Only
Equal Use
Description
Both lamps are used for greater brightness.
Lamp 1 is used.
When lamp 1 burns out, automatically
switches to lamp 2.
Lamp 2 is used.
When lamp 2 burns out, automatically
switches to lamp 1.
Both lamps are used alternatingly.
Switches after every 100 hrs. of use.
Replacing the Lamp
It is recommended that the lamp be replaced after approximately 900 cumulative hours of use or when you notice
a significant deterioration of the picture and colour quality. Carefully change the lamp by following the steps on the
next page.
If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorised LCD Projector
Dealer or Service Centre for repair. Purchase a replacement lamp unit (lamp/cage module) of the current type
BQC-XGV10WU/1 from your nearest Sharp Authorised LCD Projector Dealer or Service Centre. Then carefully
change the lamp by following the instructions on the next page. If you wish, you may have the lamp replaced at
your nearest Sharp Authorised LCD Projector Dealer or Service Centre.
CAUTION
• Potential hazard of glass particles if lamp ruptures. In case of lamp rupture, contact your nearest
Sharp Authorised LCD Projector Dealer or Service Centre for a replacement.
• Do not remove the lamp cage directly after operation of the projector. The lamp may be extremely
hot. Wait at least one hour after the power cord is disconnected to allow the surface of the lamp cage
to fully cool before removing the lamp cage.
MOUSE
ADJ.
72
Maintenance &
Tr
oubleshooting
Replacing the Lamp
• Be sure to remove the lamp cage by the handle. Be sure not to touch the glass surface of the lamp cage
or the inside of the projector.
• To avoid injury to yourself and damage to the lamp, be sure to carefully follow the steps below.
• Replace the lamp more safely by unplugging the power cord after turning off the main power.
Removing and installing the lamp unit
CAUTION
4
6
Remove the lamp
cage.
5
Attach the lamp cage cover
and turn on the main power.
1
3
Turn off the power.
2
Turn off the main
power.
Turn off the MAIN POWER
switch. (Unplug the power cord.)
Remove the lamp cage
cover.
Press POWER ON on projector. LAMP
REPLACEMENT indicator flashes red.
Then press ENTER to reset lamp timer.
Press POWER ON, and then
press ENTER on the projector.
Remove the securing screws
from the lamp cage. Hold the
lamp cage by the handle and
pull it horizontally towards you.
Loosen the user service screw
that secures the lamp cage
cover on the back of the
projector. Then slide the cover in
the direction of the arrow (to the
open mark).
Press POWER OFF. Wait until
the cooling fan stops.
Slide the lamp cage cover in the
direction of the arrow (to the
close mark) on the back of the
projector. Then turn on the MAIN
POWER switch.
7
Turn off the main power again and
remove the lamp cage cover.
Insert the new lamp
cage.
Press the lamp cage firmly into
the lamp cage compartment.
Fasten the securing screws.
Turn off the main power switch
and slide the lamp cage cover
in the direction of the arrow (to
the open mark) on the back of
the projector.
Slide the lamp cage cover in the
direction of the arrow (to the
close mark) on the back of the
projector. Then tighten the user
service screw.
8
or
Securing screws
Securing screw
Lamp 1
High angle view
Lamp 2
Attach the lamp cage
cover.
9
• You need to reset lamp timer every time when replacing the lamp and confirm it to be reset on “Lamp Timer” menu.
ENTER
ON
Page of 6
Display

Sharp XG-V10XE (serv.man29) User Manual / Operation Manual ▷ Download

  • DOWNLOAD Sharp XG-V10XE (serv.man29) Service Manual ↓ Size: 637.71 KB | Pages: 6 in PDF or view online for FREE
  • Here you can View online or download the User Manual / Operation Manual for the Sharp XG-V10XE (serv.man29) in PDF for free, which will help you to disassemble, recover, fix and repair Sharp XG-V10XE (serv.man29) Projector. Information contained in Sharp XG-V10XE (serv.man29) User Manual / Operation Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.