Sharp XG-NV51XE (serv.man9) Service Manual ▷ View online
28
XG-NV51XE/XM/XA
No.
Adjusting point
Adjusting conditions
Adjusting procedure
24
1. Receive the colour bar sig-
nal.
»
In the process mode and select L1. Check the col-
our and tint.
our and tint.
26
»
In the process mode nad select L3. Check the bass,
treble and balance.
treble and balance.
25
1. Receive the monoscope
pattern signal.
»
In the process mode and select L2. Check the pic-
ture, brightness and sharpness.
ture, brightness and sharpness.
27
RGB
performance
check
performance
check
1. Receive the RGB signal.
»
In the process mode and select L4. Check the pic-
ture, brightness, red, blue, clock, phase, horizontal
position, and vertical position.
ture, brightness, red, blue, clock, phase, horizontal
position, and vertical position.
28
Off-timer
performance
check
performance
check
»
In the process mode and select OFF. Make sure that
the off-timer starts with “5” (minutes), counts down
each minute in 1 second, and turns off the set at “0”.
the off-timer starts with “5” (minutes), counts down
each minute in 1 second, and turns off the set at “0”.
29
Thermistor
performance
check
performance
check
1. Heat the thermistor using a
dryer.
»
Make sure the “TEMP” is displayed.
31
IrDA
performance
check
performance
check
»
Make sure the IrDA signal can be received.
30
Automatic
synchronization
synchronization
1. Receive the PHASE check
pattern signal.
»
Call the VGA/S-VGA/XGA/SXGA mode and make
sure that the clock, phase, horizontal and vertical
positions can be automatically adjusted.
sure that the clock, phase, horizontal and vertical
positions can be automatically adjusted.
32
Keystone
correction
performance
check
correction
performance
check
»
Make sure the keystone correction functions well.
33
Factory settings
»
Make the following settings.
S4
“Factory setting 4”
Remote controller
setting
setting
Process
adjustment
adjustment
28
XG-NV51XE/XM/XA
No.
Adjusting point
Adjusting conditions
Adjusting procedure
24
1. Receive the colour bar sig-
nal.
»
In the process mode and select L1. Check the col-
our and tint.
our and tint.
26
»
In the process mode nad select L3. Check the bass,
treble and balance.
treble and balance.
25
1. Receive the monoscope
pattern signal.
»
In the process mode and select L2. Check the pic-
ture, brightness and sharpness.
ture, brightness and sharpness.
27
RGB
performance
check
performance
check
1. Receive the RGB signal.
»
In the process mode and select L4. Check the pic-
ture, brightness, red, blue, clock, phase, horizontal
position, and vertical position.
ture, brightness, red, blue, clock, phase, horizontal
position, and vertical position.
28
Off-timer
performance
check
performance
check
»
In the process mode and select OFF. Make sure that
the off-timer starts with “5” (minutes), counts down
each minute in 1 second, and turns off the set at “0”.
the off-timer starts with “5” (minutes), counts down
each minute in 1 second, and turns off the set at “0”.
29
Thermistor
performance
check
performance
check
1. Heat the thermistor using a
dryer.
»
Make sure the “TEMP” is displayed.
31
IrDA
performance
check
performance
check
»
Make sure the IrDA signal can be received.
30
Automatic
synchronization
synchronization
1. Receive the PHASE check
pattern signal.
»
Call the VGA/S-VGA/XGA/SXGA mode and make
sure that the clock, phase, horizontal and vertical
positions can be automatically adjusted.
sure that the clock, phase, horizontal and vertical
positions can be automatically adjusted.
32
Keystone
correction
performance
check
correction
performance
check
»
Make sure the keystone correction functions well.
33
Factory settings
»
Make the following settings.
S4
“Factory setting 4”
Remote controller
setting
setting
Process
adjustment
adjustment
28
XG-NV51XE/XM/XA
No.
Adjusting point
Adjusting conditions
Adjusting procedure
24
1. Receive the colour bar sig-
nal.
»
In the process mode and select L1. Check the col-
our and tint.
our and tint.
26
»
In the process mode nad select L3. Check the bass,
treble and balance.
treble and balance.
25
1. Receive the monoscope
pattern signal.
»
In the process mode and select L2. Check the pic-
ture, brightness and sharpness.
ture, brightness and sharpness.
27
RGB
performance
check
performance
check
1. Receive the RGB signal.
»
In the process mode and select L4. Check the pic-
ture, brightness, red, blue, clock, phase, horizontal
position, and vertical position.
ture, brightness, red, blue, clock, phase, horizontal
position, and vertical position.
28
Off-timer
performance
check
performance
check
»
In the process mode and select OFF. Make sure that
the off-timer starts with “5” (minutes), counts down
each minute in 1 second, and turns off the set at “0”.
the off-timer starts with “5” (minutes), counts down
each minute in 1 second, and turns off the set at “0”.
29
Thermistor
performance
check
performance
check
1. Heat the thermistor using a
dryer.
»
Make sure the “TEMP” is displayed.
31
IrDA
performance
check
performance
check
»
Make sure the IrDA signal can be received.
30
Automatic
synchronization
synchronization
1. Receive the PHASE check
pattern signal.
»
Call the VGA/S-VGA/XGA/SXGA mode and make
sure that the clock, phase, horizontal and vertical
positions can be automatically adjusted.
sure that the clock, phase, horizontal and vertical
positions can be automatically adjusted.
32
Keystone
correction
performance
check
correction
performance
check
»
Make sure the keystone correction functions well.
33
Factory settings
»
Make the following settings.
S4
“Factory setting 4”
Remote controller
setting
setting
Process
adjustment
adjustment
28
XG-NV51XE/XM/XA
No.
Adjusting point
Adjusting conditions
Adjusting procedure
24
1. Receive the colour bar sig-
nal.
»
In the process mode and select L1. Check the col-
our and tint.
our and tint.
26
»
In the process mode nad select L3. Check the bass,
treble and balance.
treble and balance.
25
1. Receive the monoscope
pattern signal.
»
In the process mode and select L2. Check the pic-
ture, brightness and sharpness.
ture, brightness and sharpness.
27
RGB
performance
check
performance
check
1. Receive the RGB signal.
»
In the process mode and select L4. Check the pic-
ture, brightness, red, blue, clock, phase, horizontal
position, and vertical position.
ture, brightness, red, blue, clock, phase, horizontal
position, and vertical position.
28
Off-timer
performance
check
performance
check
»
In the process mode and select OFF. Make sure that
the off-timer starts with “5” (minutes), counts down
each minute in 1 second, and turns off the set at “0”.
the off-timer starts with “5” (minutes), counts down
each minute in 1 second, and turns off the set at “0”.
29
Thermistor
performance
check
performance
check
1. Heat the thermistor using a
dryer.
»
Make sure the “TEMP” is displayed.
31
IrDA
performance
check
performance
check
»
Make sure the IrDA signal can be received.
30
Automatic
synchronization
synchronization
1. Receive the PHASE check
pattern signal.
»
Call the VGA/S-VGA/XGA/SXGA mode and make
sure that the clock, phase, horizontal and vertical
positions can be automatically adjusted.
sure that the clock, phase, horizontal and vertical
positions can be automatically adjusted.
32
Keystone
correction
performance
check
correction
performance
check
»
Make sure the keystone correction functions well.
33
Factory settings
»
Make the following settings.
S4
“Factory setting 4”
Remote controller
setting
setting
Process
adjustment
adjustment
Display