DOWNLOAD Sharp XG-NV51XE (serv.man9) Service Manual ↓ Size: 20.7 KB | Pages: 6 in PDF or view online for FREE

Model
XG-NV51XE (serv.man9)
Pages
6
Size
20.7 KB
Type
PDF
Document
Service Manual
Brand
Device
Projector / Electrical adjustment
File
xg-nv51xe-sm9.pdf
Date

Sharp XG-NV51XE (serv.man9) Service Manual ▷ View online

25
XG-NV51XE/XM/XA
No.
Adjusting point
Adjusting conditions
Adjusting procedure
10
RGB counter-
voltage
adjustment
1. Feed the black-and-red
(25%) stripe signal (XGA).
2. Make the following choice:
Group : OUTPUT 3
Subject : RC (R)
»
Using the control switches or the remote controller
buttons, adjust the data in order to minimize the
flicker.
»
Make the same adjustment for BC (B) and GC (G).
»
See if the image is equally adjusted at the center
and both sides of the screen. If not, readjust the
setting to have the image equal at right and left.
11
RGB gradation
regeneration
adjustment
1. Feed the green-only SMPTE
pattern signal.(XGA)
Group : OUTPUT 1
Subject : G1-GAIN
»
Adjust the G-GAIN data until the gradation of the
portion 
1
 (95% and 100% white) shown below can
be slightly recognized.  Make sure also that the
gradation of the portion 
2
 (0% and 5% black) is
visible.
1
2
12
RGB white
balance
1. Feed the 32-step gray scale
signal (XGA).
Group : OUTPUT 1
Subject : R1-BLK (R)
B1-BLK (B)
»
Choose the subjects R1-BLK and B1-BLK and adjust
the black balance of the gradation.
13
Horizontal
center
1. Feed the NTSC mono-
scope pattern signal.
2. Group : VIDEO 2
Subject : N358-DLY
(6)
N443-DLY
(2)
PAL-DLY
(2)
SECAM-DLY (2)
Make sure the settings are
    as above.
3. Group : VIDEO 1
Subject : NTSC-H
»
Using the control switches or the remote controller
buttons, adjust the data to have the same overscan.
14
Video picture
adjustment
1. Feed the split colour bar
signal.
Group : VIDEO 1
Subject : PICTURE
2. Connect the oscilloscope
between pin (2) of P801
and GND.
»
Using the control switches or the remote controller
buttons, adjust the black-to-white (100%) level
difference to 2.0 ±0.02 Vp-p.
2.0Vp-p
26
XG-NV51XE/XM/XA
15
Video AGC
1. Feed the split colour bar
signal.
Group : VIDEO 1
Subject : AGC
2. Connect the oscilloscope
between pin (2) of P801
and GND.
»
Using the control switches or the remote controller
buttons, adjust the black-to-white (100%) level
difference to 1.50 ±0.02 Vp-p.
16
Video
brightness
adjustment
1. Feed the baseband (split
colour bar) signal. (The
ON-AIR signal is not ac-
cepted because of its too
much noise.)
Group : VIDEO 1
Subject : BRIGHT
2. Press the control switch or
the remote control’s mute
button (to set the gamma
correction to the process
setting).
»
Using the control switches or the remote controller
buttons, adjust the setting until the black signal
becomes bit-less and set to -2 point of value.
18
NTSC colour
saturation level
1. Feed the split colour bar
signal.
Group : VIDEO 1
Subject : N-COLOR
2. Connect the oscilloscope to
pin (1) of P801.
»
Using the control switches or the remote controller
buttons, adjust the difference between the 100% white
portion and the red portion to 0.10 ±0.02 Vp-p.
   (same as 100% white)
17
Tint
1. Feed the split colour bar
signal.
Group : VIDEO 1
Subject : TINT
2. Connect the oscilloscope to
pin (4) of P801.
»
Using the control switches or the remote controller
buttons, adjust the data to have the -(B-Y) wave-
form downhill straight.
1.50Vp-p
100% White Red
No.
Adjusting point
Adjusting conditions
Adjusting procedure
27
XG-NV51XE/XM/XA
100% White Red
100% White Red
No.
Adjusting point
Adjusting conditions
Adjusting procedure
19
PAL colour
saturation level
1. Feed the PAL colour bar
signal.
Group : VIDEO 1
Subject : P-COLOR
2. Connect the oscilloscope to
pin (1) of P801.
»
Using the control switches or the remote controller
buttons, adjust the difference between the 100%
white portion and the red portion to 0.20 ±0.02 Vp-p.
20
SECAM colour
saturation level
1. Feed the SECAM colour
bar signal.
Group : VIDEO 1
Subject : S-COLOR
2. Connect the oscilloscope to
pin (1) of P801.
»
Using the control switches or the remote controller
buttons, adjust the data to have a level difference of
0.25 ±0.02 Vp-p between the 100% white portion
and the red portion.
21
Video white
balance
1. Feed the NTSC mono-
scope pattern signal
Group : VIDEO 2
Subject : R1-GAIN
B1-GAIN
»
Using the control switches or the remote controller
buttons, adjust so that the entire screen looks
evenly colourless.
22
Colour
irregularity
correction
position
1. Feed the gray-only RGB
colour signal.
2. Find the colour irregularity
position on the screen.
3. Group
: NOKO
Subject : NOKO-RL
4. Group : NOKO
Subject : NOKO-LH
»
If the colour is irregular, adjust the NOKO-RL data.
Set it to R for the right-hand colour  irregularity and
to L for the left-hand one.
»
When there is no colour irregularity, turn off the saw-
tooth waveform correction on the NOKO-LH data.
23
Colour
irregularity
correction gain
(in case of
colourirregularity)
1. Feed the gray-only RGB
colour signal.
»
Adjust R4215 to minimize the right-hand and left-
hand colour irregularity.
28
XG-NV51XE/XM/XA
No.
Adjusting point
Adjusting conditions
Adjusting procedure
24
1. Receive the colour bar sig-
nal.
»
In the process mode and select L1. Check the col-
our and tint.
26
»
In the process mode nad select L3. Check the bass,
treble and balance.
25
1. Receive the monoscope
pattern signal.
»
In the process mode and select L2. Check the pic-
ture, brightness and sharpness.
27
RGB
performance
check
1. Receive the RGB signal.
»
In the process mode and select L4. Check the pic-
ture, brightness, red, blue, clock, phase, horizontal
position, and vertical position.
28
Off-timer
performance
check
»
In the process mode and select OFF. Make sure that
the off-timer starts with “5” (minutes), counts down
each minute in 1 second, and turns off the set at “0”.
29
Thermistor
performance
check
1. Heat the thermistor using a
dryer.
»
Make sure the “TEMP” is displayed.
31
IrDA
performance
check
»
Make sure the IrDA signal can be received.
30
Automatic
synchronization
1. Receive the PHASE check
pattern signal.
»
Call the VGA/S-VGA/XGA/SXGA mode and make
sure that the clock, phase, horizontal and vertical
positions can be automatically adjusted.
32
Keystone
correction
performance
check
»
Make sure the keystone correction functions well.
33
Factory settings
»
Make the following settings.
S4
“Factory setting 4”
Remote controller
setting
Process
adjustment
Page of 6
Display

Sharp XG-NV51XE (serv.man9) Service Manual ▷ Download

  • DOWNLOAD Sharp XG-NV51XE (serv.man9) Service Manual ↓ Size: 20.7 KB | Pages: 6 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sharp XG-NV51XE (serv.man9) in PDF for free, which will help you to disassemble, recover, fix and repair Sharp XG-NV51XE (serv.man9) Projector. Information contained in Sharp XG-NV51XE (serv.man9) Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.