DOWNLOAD Sharp XG-NV21SE (serv.man4) Service Manual ↓ Size: 147.96 KB | Pages: 29 in PDF or view online for FREE

1. Make the following choice:

Group : OUTPUT 1
Subject : R1-BLK

R1-GAIN

For green, choose the sub-
jects G1-BLK and G1-
GAIN.
For blue, choose the sub-
j e c t s   B 1 - B L K   a n d   B 1 -
GAIN.

2. Connect the oscilloscope to

pin (4)(TP1101) of SC1101
for red.
Pin (4)(TP1201) of

SC1201 for green

Pin (4)(TP1301) of

SC1301 for blue

»

Choose the subject R1-BLK and adjust the black
peak level to 2.7 ±0.1V DC using the control
switches or the remote controller buttons.

»

Next, choose the subject R1-GAIN and adjust the
signal amplitude to 2.9 ±0.1 Vp-p.

»

Make the same adjustment for green and blue.

1. Make the following choice:

Group : OUTPUT 2
Subject : R2-BLK(R)

R2-GAIN

For green, choose the sub-
jects G2-BLK and G2-
GAIN.
For blue, choose the sub-
j e c t s   B 2 - B L K   a n d   B 2 -
GAIN.

2. Connect the oscilloscope to

pin (6)(TP1102) of SC1101
for red.
Pin (6)(TP1202) of

SC1201 for green

Pin (6)(TP1302) of

SC1301 for blue

»

Choose the subject R2-BLK and adjust the black
peak level to 2.7 ±0.1V DC using the control
switches or the remote controller buttons.

»

Next, choose the subject R2-GAIN and adjust the
signal amplitude to 2.9 ±0.1 Vp-p.

»

Make the same adjustment for green and blue.

»

Feed the SVGA gradation pattern single-colour sig-
nal and make sure that there is no difference in
brightness between adjacent vertical lines. If there
is a difference, make fine adjustment by choosing
the following subjects.

R2-GAIN for red
G2-GAIN for green
B2-GAIN for blue.

1. Feed the XGA mode 75-Hz

black signal.

2. Make the following choice:

Group : OUTPUT 3
Subject : SH-PHASE
(Have the standard level at
8.)
F i x   t h e   R - ,   G -   a n d   B -
PHASE settings all to 4.

»

Using the control switches or the remote controller
buttons, make sure that the “OUTPUT 3” charac-
ters are not blurry and there is no ghost image. If
such blur or ghost occurs, finely adjust the setting
in the range of 7~9.

2.9Vp-p

2.7V DC

2.9Vp-p

2.7V DC

1. Feed the black-and-red

(25%) stripe signal (SVGA)
to RGB1.

2. Make the following choice:

Group : OUTPUT 3
Subject : RC (R)

3. Change to the outer RG1 at

the shoot of the operating
switches or the remote con-
troller buttons.

»

Using the control switches or the remote controller
buttons, adjust the data in order to minimize the flicker.

»

Make the same adjustment for BC (B) and GC (G).

»

See if the image is equally adjusted at the center
and both sides of the screen. If not, readjust the
setting to have the image equal at right and left.

1. Feed the 32-step gray scale

signal (SVGA).
Group : OUTPUT 1
Subject : R1-BLK

R1-GAIN (R)
B1-BLK
B1-GAIN (B)

»

Choose the subjects R1-BLK and B1-BLK and adjust
the black balance of the gradation. Choose the
subjects R1-GAIN and B1-GAIN and adjust the gray-
to-while balance.

1. Feed the split colour bar

signal.
Group : VIDEO 1
Subject : PICTURE

2. Connect the oscilloscope

between pin (2) of P801
and GND.

»

Using the control switches or the remote controller
buttons, adjust the black-to-white (100%) level
difference to 2.2 ±0.02 Vp-p.

2.2 Vp-p

1. Feed the NTSC mono-

scope pattern signal.

2. Group : VIDEO 2

Subject : N358-DLY

N443-DLY
PAL-DLY
SECAM-DLY

Make sure all the settings
are zero (0).

3. Group : VIDEO 1

Subject : NTSC-H

»

Using the control switches or the remote controller
buttons, adjust the data to have the same overscan.

1. Feed the split colour bar

signal.
Group : VIDEO 1
Subject : AGC

2. Connect the oscilloscope

between pin (2) of P801
and GND.

»

Using the control switches or the remote controller
buttons, adjust the black-to-white (100%) level
difference to 1.65 ±0.02 Vp-p.

1. Feed the baseband (split

colour bar) signal. (The
ON-AIR signal is not ac-
cepted because of its too
much noise.)
Group : VIDEO 1
Subject : BRIGHT

2. Press the control switch or

the remote control’s mute
button (to set the gamma
correction to the process
setting).

»

Using the control switches or the remote controller
buttons, adjust the setting until the black signal
becomes bit-less.

1. Feed the split colour bar

signal.
Group : VIDEO 1
Subject : N-COLOR

2. Connect the oscilloscope to

pin (1) of P801.

»

Using the control switches or the remote controller
buttons, adjust the difference between the 100%
white portion and the red portion to 0.1 ±0.02 Vp-p.

1.65 Vp-p

1. Feed the split colour bar

signal.
Group : VIDEO 1
Subject : TINT

2. Connect the oscilloscope to

pin (5) of P801.

»

Using the control switches or the remote controller
buttons, adjust the data to have the -(B-Y) waveform
downhill straight.

100% White Red

0.1Vp-p

1. Feed the NTSC mono-

scope pattern signal.
Group : VIDEO 2
Subject : R1-GAIN

B1-GAIN

»

Using the control switches or the remote controller
buttons, adjust the data so that the white balance be
just the best white balance.
If the black side is not properly adjusted, first
readjust the black side by making the following
choice:

Group : OUTPUT 1
Subject : R1-BLK

B1-BLK

Then, make the following choice:

Group : VIDEO 2
Subject : R1-GAIN

B1-GAIN

Readjust the related data.
Since the subjects R1-BLK and B1-BLK are com-
mon for the RGB input and VIDEO input, feed the
RGB signal again to adjust the white balance.

1. Feed the SECAM colour

bar signal.
Group : VIDEO 1
Subject : S-COLOR

2. Connect the oscilloscope to

pin (1) of P801.

»

Using the control switches or the remote controller
buttons, adjust the data to have a level difference of
0.48 ±0.02 Vp-p between the 100% white portion and
the red portion.

1. Receive the colour bar sig-

nal.

»

In the process mode and select L1. Check the colour
and tint.

1. Receive the monoscope

pattern signal.

»

In the process mode and select L2. Check the pic-
ture, brightness and sharpness.

1. Feed the PAL colour bar

signal.
Group : VIDEO 1
Subject : P-COLOR

2. Connect the oscilloscope to

pin (1) of P801.

»

Using the control switches or the remote controller
buttons, adjust the difference between the 100%
white portion and the red portion to 0.48±0.02 Vp-p.

100% White Red

0.48Vp-p

100% White Red

0.48Vp-p