Sharp XG-F210X (serv.man11) User Manual / Operation Manual ▷ View online
XR-30S/XR-30X/XG-F210X
1 – 13
Removing and Installing
the Lamp Unit
Do not touch the glass surface of the lamp
unit or the inside of the projector.
unit or the inside of the projector.
To avoid injury to yourself and damage to the
lamp, make sure you carefully follow the steps
below.
Do not loosen other screws except for the
lamp unit cover and lamp unit.
below.
Do not loosen other screws except for the
lamp unit cover and lamp unit.
Press STANDBY/ON on the projec-
tor or STANDBY on the remote
control to put the projector into
standby mode.
Wait until the cooling fan stops.
Warning!
Do not remove the lamp unit from the projec-
tor right after use. The lamp and parts around
the lamp will be very hot and may cause burns
or injury.
tor right after use. The lamp and parts around
the lamp will be very hot and may cause burns
or injury.
Disconnect the power cord.
Unplug the power cord from the AC
socket.
Leave the lamp until it has fully cooled
down (about 1 hour).
socket.
Leave the lamp until it has fully cooled
down (about 1 hour).
Remove the lamp unit cover.
Turn the projector over. Loosen the user
service screw (
service screw (
) that secures the lamp
unit cover. Remove the lamp unit cover
(
(
).
Lamp unit
AN-XR30LP
AN-XR30LP
Info
Optional
accessory
AC socket
User service screw
(for lamp unit cover)
(for lamp unit cover)
1
2
3
STANDBY/ON button
1
1
2
2
XR-30S/XR-30X/XG-F210X
1 – 14
Remove the lamp unit.
Loosen the securing screws from the
lamp unit. Hold the lamp unit and pull it
in the direction of the arrow. At this time,
keep the lamp unit horizontal and do not
tilt it.
lamp unit. Hold the lamp unit and pull it
in the direction of the arrow. At this time,
keep the lamp unit horizontal and do not
tilt it.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
Insert the new lamp unit.
Press the lamp unit firmly into the lamp
unit compartment. Fasten the securing
screws.
unit compartment. Fasten the securing
screws.
Replace the lamp unit cover.
Align the tab on the lamp unit cover
(
(
) and place it while pressing the tab
(
) to close it. Then tighten the user ser-
vice screw (
) to secure the lamp unit
cover.
4
5
6
Connect the power cord.
Plug the power cord into the AC socket
of the projector.
of the projector.
Reset the lamp timer.
While simultaneously holding down
MENU/HELP, ENTER and on the pro-
jector, press
jector, press
STANDBY/ON on the pro-
jector.
"LAMP 0000H" is displayed, indicating
that the lamp timer is reset.
"LAMP 0000H" is displayed, indicating
that the lamp timer is reset.
Make sure to reset the lamp timer only when
replacing the lamp. If you reset the lamp timer
and continue to use the same lamp, this may
cause the lamp to become damaged or ex-
plode.
replacing the lamp. If you reset the lamp timer
and continue to use the same lamp, this may
cause the lamp to become damaged or ex-
plode.
1
2
Info
AC socket
Securing screws
ENTER button
MENU/HELP
button
button
button
If the lamp unit and lamp unit cover are
not correctly installed, the power will not
turn on, even if the power cord is con-
nected to the projector.
not correctly installed, the power will not
turn on, even if the power cord is con-
nected to the projector.
Info
STANDBY/ON
button
button
XR-30S/XR-30X/XG-F210X
1 – 14
Remove the lamp unit.
Loosen the securing screws from the
lamp unit. Hold the lamp unit and pull it
in the direction of the arrow. At this time,
keep the lamp unit horizontal and do not
tilt it.
lamp unit. Hold the lamp unit and pull it
in the direction of the arrow. At this time,
keep the lamp unit horizontal and do not
tilt it.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
Insert the new lamp unit.
Press the lamp unit firmly into the lamp
unit compartment. Fasten the securing
screws.
unit compartment. Fasten the securing
screws.
Replace the lamp unit cover.
Align the tab on the lamp unit cover
(
(
) and place it while pressing the tab
(
) to close it. Then tighten the user ser-
vice screw (
) to secure the lamp unit
cover.
4
5
6
Connect the power cord.
Plug the power cord into the AC socket
of the projector.
of the projector.
Reset the lamp timer.
While simultaneously holding down
MENU/HELP, ENTER and on the pro-
jector, press
jector, press
STANDBY/ON on the pro-
jector.
"LAMP 0000H" is displayed, indicating
that the lamp timer is reset.
"LAMP 0000H" is displayed, indicating
that the lamp timer is reset.
Make sure to reset the lamp timer only when
replacing the lamp. If you reset the lamp timer
and continue to use the same lamp, this may
cause the lamp to become damaged or ex-
plode.
replacing the lamp. If you reset the lamp timer
and continue to use the same lamp, this may
cause the lamp to become damaged or ex-
plode.
1
2
Info
AC socket
Securing screws
ENTER button
MENU/HELP
button
button
button
If the lamp unit and lamp unit cover are
not correctly installed, the power will not
turn on, even if the power cord is con-
nected to the projector.
not correctly installed, the power will not
turn on, even if the power cord is con-
nected to the projector.
Info
STANDBY/ON
button
button
XR-30S/XR-30X/XG-F210X
1 – 14
Remove the lamp unit.
Loosen the securing screws from the
lamp unit. Hold the lamp unit and pull it
in the direction of the arrow. At this time,
keep the lamp unit horizontal and do not
tilt it.
lamp unit. Hold the lamp unit and pull it
in the direction of the arrow. At this time,
keep the lamp unit horizontal and do not
tilt it.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
Insert the new lamp unit.
Press the lamp unit firmly into the lamp
unit compartment. Fasten the securing
screws.
unit compartment. Fasten the securing
screws.
Replace the lamp unit cover.
Align the tab on the lamp unit cover
(
(
) and place it while pressing the tab
(
) to close it. Then tighten the user ser-
vice screw (
) to secure the lamp unit
cover.
4
5
6
Connect the power cord.
Plug the power cord into the AC socket
of the projector.
of the projector.
Reset the lamp timer.
While simultaneously holding down
MENU/HELP, ENTER and on the pro-
jector, press
jector, press
STANDBY/ON on the pro-
jector.
"LAMP 0000H" is displayed, indicating
that the lamp timer is reset.
"LAMP 0000H" is displayed, indicating
that the lamp timer is reset.
Make sure to reset the lamp timer only when
replacing the lamp. If you reset the lamp timer
and continue to use the same lamp, this may
cause the lamp to become damaged or ex-
plode.
replacing the lamp. If you reset the lamp timer
and continue to use the same lamp, this may
cause the lamp to become damaged or ex-
plode.
1
2
Info
AC socket
Securing screws
ENTER button
MENU/HELP
button
button
button
If the lamp unit and lamp unit cover are
not correctly installed, the power will not
turn on, even if the power cord is con-
nected to the projector.
not correctly installed, the power will not
turn on, even if the power cord is con-
nected to the projector.
Info
STANDBY/ON
button
button
