Sharp XG-C50XE (serv.man35) Driver / Update ▷ View online
26
Multi
Scan Setting
This function allows the software to automatically identify and control all
the projectors connected to the PC without having to the ports and
models. To use this function, the COM ports and
the projectors connected to the PC without having to the ports and
models. To use this function, the COM ports and
IP address
to be scanned
with “Scan Setting” must be set beforehand.
For details and setting of “Scan Setting” see below.
For details and setting of “Scan Setting” see below.
1
Select “Scan Setting” from the “File” menu.
Set the projectors to be scanned here.
1
COM port enable/disable check box
The serial number is assigned when using multiple connections
which do not use IDs.
which do not use IDs.
2
Set the COM port
Transmission Speed
.
3
IP address input area
4
List of input IP addresses and enable/disable check box
5
Add button
When clicked after inputting the IP address, the address is added to
the list in 4.
When clicked after inputting the IP address, the address is added to
the list in 4.
6
Delete button
When clicked after selecting the IP address in 4, that address is
deleted.
When clicked after selecting the IP address in 4, that address is
deleted.
7
List of projectors whose IDs are redundant.
8
List of projectors whose IDs are missing.
9
Scan button
0
OK button
q
Cancel button
1
8
5
6
9
0
q
7
2
4
3
27
Adjusting and
Controlling
Multi
2
Set the port to which the projector is connected.
● In 1, check the check box of the COM port to which the projector
is connected.
● To use a LAN, input the IP address in 3, click the “Add” button,
then check the check box in 4.
LAN connections are possible only with models from the XG-V10
series with the optional extension board (AN-L10T) installed.
series with the optional extension board (AN-L10T) installed.
3
Click the “Scan” button.
The connected projectors are identified.
● If projectors with the same IDs are discovered through scanning,
the data for those projectors is displayed in the “Redundant” area.
If this happens, reassign suitable IDs to the projectors.
If this happens, reassign suitable IDs to the projectors.
● The results of scanning are compared with the pre-scanning All
Projector List and the data for projectors that could not be
confirmed as being connected is displayed in the “Missing” area.
confirmed as being connected is displayed in the “Missing” area.
4
Click “OK” if you wish to create an “All Projector List”
based on the results of scanning.
based on the results of scanning.
If you do not wish to create an “All Projector List”, click “Cancel”.
Deleting the set IP address
1
Select the IP address to be deleted in 4
4
4
4
4.
2
Click the “Delete” button.
28
Multi
Projector Setting
When “Multiple Projector Operation Mode (Use ID Number)” is selected
in “Operation Mode Setting”, it is possible to add projectors manually
without using the scan setting automatic identification function. In
addition, when “Multiple Projector Operation Mode (Don’t Use ID
Number)” or “Single Projector Operation Mode” is selected, make the
respective settings at “Projector Setting”.
in “Operation Mode Setting”, it is possible to add projectors manually
without using the scan setting automatic identification function. In
addition, when “Multiple Projector Operation Mode (Don’t Use ID
Number)” or “Single Projector Operation Mode” is selected, make the
respective settings at “Projector Setting”.
Multiple Projector Operation Mode
1
From the “File” menu, select “Projector Setting”.
1
Select the ID number.
2
Select the port.
3
Select the transmission speed.
4
Input the IP address.
5
Enable/disable check box
6
Select the projector model.
7
Backup function enable/disable check box
8
Backup projector selection pull-down menu
9
Apply button.
2
Select the ID number.
If selecting “Don’t use ID Number” in “Operation Mode Setting” (
page
25
), you don’t need to select the ID number here.
3
Select the port to which the projector is connected.
If using the RS-232C connection, select a COM port to be used from
“Port” pull-down menu.
If using the LAN connection, select “LAN”.
“Port” pull-down menu.
If using the LAN connection, select “LAN”.
LAN connections are possible only with models from the XG-V10
series with the optional extension board (AN-L10T) installed.
series with the optional extension board (AN-L10T) installed.
1
2
3
4
5
6
8
7
9
29
Adjusting and
Controlling
Multi
4
Set the Port Status.
If using the RS-232C connection, select the transmission speed
between the computer and the projector.
If using a LAN connection, input the projector’s IP address.
between the computer and the projector.
If using a LAN connection, input the projector’s IP address.
● Set the transmission speed here and confirm the transmission speed
on the projector to the same speed.
● For instructions on the projector’s transmission speed setting, refer
to the projector’s operation manual.
● The transmission speed of the PG-A10 Series and PG-A20X is fixed
at 9,600 bps.
5
Select the projector model and check the “Use Projector”
check box.
check box.
6
Set the backup projector.
If necessary, set the backup projector. See
page 56
for details.
7
Click the “Apply” button.
Click on the first or last page to see other XG-C50XE (serv.man35) service manuals if exist.