Sharp XG-C50XE (serv.man30) User Manual / Operation Manual ▷ View online
Easy to Use Functions
-57
Displaying Dual Pictures (
Pict in Pict
)
Picture in Picture function allows you to display two pictures on the same screen. You can
display the image input from INPUT 3 or 4 as an inset picture overlapping the main picture
from INPUT 1 or 2.
display the image input from INPUT 3 or 4 as an inset picture overlapping the main picture
from INPUT 1 or 2.
Displaying the Inset Picture
1
Press
.
2
Press
or
on the remote
control or
on the projector
to switch the image in the in-
set picture .
set picture .
3
Press '
'
'
'
', "
"
"
"
", \
\
\
\
\ and |
|
|
|
| to set the
position of the inset picture.
• Press
to stop the frame from mov-
ing or to make the frame disappear.
4
Press
to move the inset pic-
ture.
• The inset picture will be moved to the
inset picture frame.
Note
• The inset picture can only be displayed
with composite video (NTSC/PAL/
SECAM) or S-Video signal.
SECAM) or S-Video signal.
• The Freeze function works only with the
inset picture, when the Pict in Pict mode
is in operation.
is in operation.
When the signal entered into INPUT 1 or 2
is as follows, Pict in Pict does not work:
is as follows, Pict in Pict does not work:
• With a resolution that exceeds SXGA.
• When the input signal is 480
I
, 480P,
540P, 580
I,
580P, 720P, 1035
I
or 1080
I
.
• When the input signal has changed to
the Interlace mode using RGB signals.
• When the picture display mode is set to
“DOT BY DOT”.
• When no signals are sent to INPUT 1 or
2, or when the resolution or refresh rate
(vertical frequency) is changed.
(vertical frequency) is changed.
'
,
"
,
\
,
|
buttons
PinP button
INPUT 3/4 buttons
UNDO button
ENTER button
58
Black Screen Function
-58
BLACK SCREEN
button
button
" Projected Image
This function can be used to display a black screen.
Blacking out the Pro-
jected Image
jected Image
1
Press
.
• The screen turns black and “BLACK
SCREEN” is displayed on the screen.
2
To return to the original
projected image, press
again.
projected image, press
again.
Easy to Use Functions
-59
Displaying the Break Timer
"On-screen Display
Displaying and Setting
the Break Timer
the Break Timer
1
Press
. The break timer
starts to count down from 5
minutes.
minutes.
2
When “
” is displayed, press
'
'
'
'
' , "
"
"
"
" , \
\
\
\
\ or |
|
|
|
| to set the break
timer.
• You can set anywhere between 1 and
60 minutes (in 1 minute units).
• The break timer starts to count down
as soon as ' , " , \ or | is pressed.
3
Press
to cancel the break
timer.
Note
• Auto Power Off will be temporarily dis-
abled during the break timer.
When no input signal is detected for more
than 15 minutes, the projector will auto-
matically shut off if the break timer has
elapsed.
When no input signal is detected for more
than 15 minutes, the projector will auto-
matically shut off if the break timer has
elapsed.
• The break timer will be displayed on the
startup image. To change the screen dis-
played during the break timer, change the
setting of “Startup Image” (see page
played during the break timer, change the
setting of “Startup Image” (see page
68
).
BREAK TIMER
button
button
This function can be used to show the remaining time for break during meeting.
'
,
"
,
\
,
|
buttons
-60
Color Management System (C. M. S.)
Selecting the Color
Reproduction Mode
Reproduction Mode
Select “Color Selected” in the “C.M.S.”
menu on the menu screen.
➝ For operating the menu screen, see
pages
menu on the menu screen.
➝ For operating the menu screen, see
pages
42 to 45
.
Note
• For additional information about sRGB
function, visit “http://www.srgb.com/”.
• “sRGB” cannot be selected for “Color Se-
lected” on the C.M.S. menu when “Com-
ponent” is selected for “Signal Type” on
the “Picture” menu.
ponent” is selected for “Signal Type” on
the “Picture” menu.
• When “sRGB” is selected;
• The gamma correction cannot be set.
• “Red”, “Blue” or “CLR Temp” in “Picture”
cannot be adjusted.
• If “Standard” or “sRGB” is selected for
“Color Selected”, other items (e.g., Target)
cannot be adjusted.
cannot be adjusted.
Info
• When “
sRGB
” is selected, the projected
image may become dark; however, this
does not indicate a malfunction.
does not indicate a malfunction.
Selecting the Target
Color
Color
Select “Target” in the “C.M.S.” menu on
the menu screen.
➝ For operating the menu screen, see
pages
the menu screen.
➝ For operating the menu screen, see
pages
42 to 45
.
This function allows you individually adjust the display characteristics of six colors (R: Red,
Y: Yellow, G: Green, C: Cyan, B: Blue, M: Magenta) .
Y: Yellow, G: Green, C: Cyan, B: Blue, M: Magenta) .
Red
Cyan
Yellow
Blue
Green
Magenta
-60
Description
Sharp default setting
“Lightness”, “Chroma” and “Hue” can
be adjusted for each of the six colors.
The mode changes to sRGB
“Lightness”, “Chroma” and “Hue” can
be adjusted for each of the six colors.
The mode changes to sRGB
Selected item
Standard
Custom 1-3
Custom 1-3
sRGB
Click on the first or last page to see other XG-C50XE (serv.man30) service manuals if exist.