XG-C50XE (serv.man29). Basic operation — Sharp Projector User Guide / Operation Manual

Model
XG-C50XE (serv.man29)
Pages
18
Size
1.4 MB
Type
PDF
Document
User Guide / Operation Manual
Brand
Device
Projector / Basic operation
File
xg-c50xe-sm29.pdf
Date

View Sharp XG-C50XE (serv.man29) User Guide / Operation Manual online

Basic Operation
Basic Operation
Image Projection
Keycode input box
-34
Lamp
replacement
indicator
Power
indicator
INPUT
button
',"\|
buttons
MENU
button
ENTER
button
Power (ON)
button
INPUT
buttons
'"\|
buttons
MENU button
ENTER
button
Power (OFF)
button
Basic Procedure
Connect the required external equipment to the pro-
jector before operating the following procedures.
Info
• The language preset at the factory is English.
If you want to change the on-screen display
to another language, reset the language ac-
cording to the procedure on page 
36
.
1
Plug the power cord into the
wall outlet.
• The power indicator illuminates red, and
the projector enters standby mode.
2
Press 
ON
 on the projector or on
the remote control.
• The power indicator illuminates green.
After the lamp replacement indicator il-
luminates, the projector is ready to start
operation.
Note
• The lamp replacement indicator il-
luminates, indicating the status of the
lamp.
Green: The lamp is ready.
Green blinking: The lamp is
warming up.
Red: The lamp should be replaced.
• If the power is turned off and immediately
switched on again, the lamp replacement
indicator may take time to illuminate.
• When controlling the projector using
RS-232C commands from a com-
puter, wait for at least 30 seconds
after the power has been turned on,
and then transmit the commands.
When “Anti-Theft” (see page 
75
) is set,
the keycode input box will appear.
• Enter the keycode.
Note
• When entering the keycode, press
the buttons previously set on the
projector or the remote control.
Info
• When “Anti-Theft” is set, enter the
keycode or the input display will not ap-
pear. Even when the signal is input, the
display will not appear. (see page 
75
.)
Power (ON)
button
Power (OFF)
button
Basic Operation
-35
3
Press 
 or 
 on
the remote control to select the
INPUT mode.
• After pressing   once on the projector,
use 
 to select the desired input mode.
Note
•When no signal is received, “NO
SIGNAL.”will be displayed. When a
signal that the projector is not pre-
set to receive is received, “NOT
REG.” will be displayed.
• When “Auto Search” is “ON”, the
INPUT modes with signals can be
selected. (see page 
64
.)
• The INPUT mode is not displayed
when “OSD display” is set to “Level
A” or “Level B”. (see page 
65
.)
About the INPUT modes
VOLUME
buttons
4
Press 
 or 
 on the remote
control to adjust the volume.
Note
• Pressing 
 will lower the volume.
Pressing 
 will raise the volume.
• On the projector, the volume can be
adjusted by pressing 
 or 
.
  , 
  on the projector operate
as cursor buttons (\, |) when the
menu screen is active.
"On-screen Display (Example)
Using RGB
Using
Component
INPUT 2 mode
Using
Component
INPUT 1 mode
INPUT 3 mode
   Using Video
INPUT 4 mode
   Using S-Video
Using RGB
➝➝
Used for projecting im-
ages from equipment that
sends RGB signals or
component  signals con-
nected to the RGB input
terminal.
Used for  projecting  im-
ages  from equipment
connected to the VIDEO
input terminal.
Used for projecting im-
ages from equipment
connected to the S-
VIDEO input terminal.
INPUT 1
INPUT 2
(RGB/
Component)
INPUT 3
(Video)
INPUT 4
(S-Video)
Image Projection
Power (ON)
button
5
Press 
  to temporarily turn
off the sound.
Note
• Pressing 
  again will turn the
sound back on.
6
Press 
, then press 
 again
while the confirmation message
is displayed, to turn off the pro-
jector.
Note
• If you accidentally pressed 
 and
do not want to turn off the power,
wait until the confirmation message
disappears.
Info
• Do not unplug the power cord dur-
ing projection or cooling fan opera-
tion. This can cause damage due
to the rise in internal temperature,
as the cooling fan also stops.
• When connected to equipment such
as an amplifier, be sure to turn off
the power to the equipment con-
nected first and then to the projec-
tor.
Selecting the On-screen
Display Language
• The on-screen display language of the
projector can be set to English, German,
Spanish, Dutch, French, Italian, Swedish,
Portuguese, Chinese, Korean or Japa-
nese.
1
Press 
.
• The menu will be displayed.
2
Press  \  or  |  to select “Lan-
guage”.
MUTE button
-36
Power (OFF)
button
ENTER button
MENU
button
'"\|
buttons
Basic Operation
-37
3
Press ' or " to select the de-
sired language, and then press
.
4
Press 
.
• The desired language will be set as
the on-screen display.

Download Sharp XG-C50XE (serv.man29) User Guide / Operation Manual

Here you can view online or download Sharp XG-C50XE (serv.man29) User Guide / Operation Manual in pdf. This User Guide / Operation Manual can help you recover, restore, fix, disassemble and repair Sharp XG-C50XE (serv.man29) Projector. Information contained in Sharp XG-C50XE (serv.man29) service manual (repair manual) typically includes:

  • Disassembly, troubleshooting, programming, maintenance, remote, adjustment, installation and setup instructions.
  • Schematics, wiring and block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Parts list (bill of materials).