Sharp XG-C430X Service Manual ▷ View online
XG-C330X/C430X
4 – 8
2. Cautions for 3D color shading correction/adjustment
The following measurement and adjustment must be performed under the same conditions using the following:
• Dark room (Block out stray light.)
• Diffuse reflection (mat type) screen
The setting of the projector must be performed under the following conditions:
• Power save disabled (to keep the lamp stable during measurement)
• Auto search canceled (to fix to INPUT1)
• RGB mode of the input terminal COMPUTER1 (component mode canceled - just to be sure)
1. System setting (“Setting -” System setting””)
Condition setting for C330/C430
9
Sample-hold pulse
delay amount adjust-
ment
delay amount adjust-
ment
1) Input the black signal of XGA mode.
2) Select the following.
2) Select the following.
Group: OUTPUT3
Adjustment item: ENBR-DLY
G: ENBG-DLY
B: ENBB-DLY
Adjustment item: ENBR-DLY
G: ENBG-DLY
B: ENBB-DLY
1) Check the blur and ghost of characters of OUTPUT3.
2) Raise the ENBR-DLY value until pre-ghost appears on the left of
2) Raise the ENBR-DLY value until pre-ghost appears on the left of
characters of OSD.
3) When the value is reduced by 1 to 2 points, pre-ghost disappears.
Set to the value reduced by 3 from the value where pre-ghost dis-
appears.
(Set to 16 in the following case: When the ENBR-DLY value is 20,
pre-ghost appears; when it is 19, pre-ghost disappears.)
appears.
(Set to 16 in the following case: When the ENBR-DLY value is 20,
pre-ghost appears; when it is 19, pre-ghost disappears.)
4) Adjust green and blue in the same way.
NOTE: EPSON panels may vary by 1 to 2 points from lot to lot. To
improve the ghost quality, perform this adjustment.
10
RGB counter voltage
adjustment
adjustment
1) Input the counter voltage adjustment
signal. (XGA)
2) Select the following.
Group: OUTPUT1
Adjustment item: R-COM
G-COM
B-COM
R-COM2
G-COM2
B-COM2
Adjustment item: R-COM
G-COM
B-COM
R-COM2
G-COM2
B-COM2
1) Adjust flicker using the operation SW or button on the remote con-
trol so that it becomes minimum.
2) When flicker appears on the screen unevenly, adjust the center
area considering the whole balance.
11
RGB white balance
adjustment
adjustment
1) Input the RGB 50% gray signal.
(XGA60Hz)
2) Select the following.
Group: OUTPUT1
Adjustment item: R1-BLK (R)
B1-BLK (B)
Adjustment item: R1-BLK (R)
B1-BLK (B)
1) 1. Adjust R1-BLK and B1-BLK so that the following chromaticity
values are obtained in the middle of the screen using CL200.
x = 294
x = 294
± 5, y = 327 ± 5
12
sRGB white balance
adjustment
adjustment
1) Input the RGB 50% gray signal.
2) Select the following.
2) Select the following.
Group: OUTPUT1
Adjustment item: S-G1-BLK
S-B1-BLK
Adjustment item: S-G1-BLK
S-B1-BLK
1) Adjust S-G1-BLK and S-B1-BLK so that the following chromaticity
values are obtained in the middle of the screen using CL200.
x = 322
x = 322
± 5, y = 341 ± 5
13
Auto keystone initial-
ization
ization
1) Select the following.
Group: LINE
Adjustment item: Calibration
Adjustment item: Calibration
1) With the set placed on a level surface, press the ENTER key and
check that K-Sensor value is 0
± 3 (125 - 3).
Check that keystone is caused by tilting the unit.
14
Model name writing
1) Write the model name with RS232C
command.
1) C430: MF_10000 (default)
C330: MF_10001
15
Tracking check
1) Input the RGB 10-step gray scale sig-
nal (inversion on top and bottom).
2) Select the following.
Group: OUTPUT3
Adjustment item: GAMMA
Adjustment item: GAMMA
1) Check the lower gradation tracking.
When it is improper, optimize the GAMMA value.
1: Default (normal)
2: Red and blue down
3: Red and blue up
1: Default (normal)
2: Red and blue down
3: Red and blue up
NOTE: When changing the GAMMA value, readjust the white bal-
ance.
16
Auto color shading
correction
correction
1) Perform the auto color shading correc-
tion using the color shading correction
system (ccdc).
system (ccdc).
1) Check that remarkable color shading is not found on the screen.
System option
Simultaneous writing of 3D correction value:
Simultaneous writing of 3D correction value:
No (not checked)
Char transmission interval:
0 ms
Binary interval:
2 ms
Creation of correction value by linear correction factor:
No (not checked)
Number of image captures (during adjustment or measurement): Twice
No.
Adjustment Item
Adjustment Conditions
Adjustment Procedures
XG-C330X/C430X
4 – 9
2. Teaching
Basically, teaching should be measured only once from model to model. However, if the optical characteristics of the set are changed significantly,
it is necessary to reset the conditions according to changes and to perform remeasurement.
it is necessary to reset the conditions according to changes and to perform remeasurement.
Measurement method of correction factor
1) Determine the standard set of C330/C430. Each one unit (n units)
2) Switch the set to the RGB mode of the input terminal COMPUTER1.
3) Execute teaching of the standard set under the following conditions.
Condition setting for C330/C430
3. Color shading correction (adjustment)
Condition setting for C330/C430
Correction method
Select the model name created in the section (2) and perform color shading correction/adjustment.
If the set has significantly different optical characteristics from the standard or shows color shading or line dropouts, execute teaching and adjust it
using the correction factor.
using the correction factor.
3. ELECTROCAL ADJUSTMENT (2)
Number of image captures (during teaching):
4 times
Model name:
Enter the model name newly.
Resolution:
1024 x S768
Binary interval:
2 ms
Correction value, X direction:
33
Correction value, Y direction:
25
Number of correction bits:
8
Adjustment value, minimum:
-32
Adjustment value, center:
0
Adjustment value, maximum:
32
Number of teachings:
5
Teaching interval:
32
Brightness variation direction by adjustment value: Brightness UP by increasing the adjustment value (checked)
Adjustment point:
Adjustment point:
3D (checked)
TG system (selected)
Tone 0 (checked)
Tone 1 (checked)
Other tones are not checked.
TG system (selected)
Tone 0 (checked)
Tone 1 (checked)
Other tones are not checked.
Adjustment point (Test pattern display level)
Tone 0:
Tone 0:
44%
Tone 1:
64%
Adjustment color:
Adjustment with RGB (checked)
Correction setting
Tone 7:
Tone 7:
Default
Tone 6:
Default
Tone 5:
Default
Tone 4:
Default
Tone 3:
Default
Tone 2:
Default
Tone 1:
Correction by correction factor
Tone 0:
Correction by correction factor
No.
Adjustment Item
Adjustment Conditions
Adjustment Procedures
17
DTV bright/contrast
adjustment
adjustment
1) Select the following.
Group: DTV
Adjustment item: Contrast
Bright
Adjustment item: Contrast
Bright
1) Check the fixed values.
Contrast: 10
Bright: 40
Bright: 40
18
DTV tint adjustmen
1) Select the following.
Group: DTV
Adjustment item: Tint
Adjustment item: Tint
1) Check the fixed value.
Tint: 5
19
TV color saturation
adjustment
adjustment
1) Select the following.
Group: DTV
Adjustment item: Color
Adjustment item: Color
1) Check the fixed value.
Color: 12
System option
XG-C330X/C430X
4 – 10
20
DVD bright/contrast
adjustment
adjustment
1) 1. Select the following.
Group: DVD
Adjustment item: Contrast
Bright
Adjustment item: Contrast
Bright
1) Check the fixed values.
Contrast: 9
Bright: 40
Bright: 40
21
DVD tint adjustment
1) Select the following.
Group: DVD
Adjustment item: Tint
Adjustment item: Tint
1) Check the fixed value.
Tint: 5
22
DVD color saturation
adjustment
adjustment
1) Select the following.
Group: DVD
Adjustment item: Color
Adjustment item: Color
1) Check the fixed value.
Color: 12
23
Video bright/contrast
adjustment
adjustment
1) Select the following.
Group: VIDEO
Adjustment item: Contrast
Bright
Adjustment item: Contrast
Bright
1) Check the fixed values.
Contrast: 8
Bright: 40
Bright: 40
24
Video tint adjustment
1) Select the following.
Group: VIDEO
Adjustment item: N-Tint
P-Tint
S-Tint
Adjustment item: N-Tint
P-Tint
S-Tint
1) Check the fixed values.
N-Tint: 5
P-Tint: 5
S-Tint: 5
P-Tint: 5
S-Tint: 5
25
Video color saturation
adjustment
adjustment
1) Select the following.
Group: VIDEO
Adjustment item: N-Color
P- Color
S- Color
Adjustment item: N-Color
P- Color
S- Color
1) Check the fixed values.
N-Color: 6
P- Color: 6
S- Color: 6
P- Color: 6
S- Color: 6
26
RGB tone reproduction
adjustment
adjustment
1) Input the SMPTE pattern.
2) Group: OUTPUT1
2) Group: OUTPUT1
Adjustment item: G1-BLK
1) Check that white 100% and 95% tones are visible.
2) If visibility of the white tones is different, fine adjust G1-BLK.
2) If visibility of the white tones is different, fine adjust G1-BLK.
27
White balance check
RGB input, sRGB input, component input,
video input, S-video input
video input, S-video input
1) Check that there is no disturbance in the white balance using a
monitor.
28
Vertical stripe level
check
check
1) Receive the RGB gray scale signal.
1) It must be better than the vertical stripe boundary sample.
29
Checking of off-timer
performance
performance
1) Select OFF in the process mode.
Make sure that the off-timer starts with 5-minute display, counts
down 1minute for 1second, and turns off when 0minute is dis-
played.
down 1minute for 1second, and turns off when 0minute is dis-
played.
30
Checking of ther-
mistor performance
mistor performance
1) Heat the thermistor with a hair dryer.
1) Make sure the temperature is displayed.
31
Automatic sync opera-
tion
tion
1) Receive the phase checking pattern
signal.
1) Make sure that Clock, Phase, H-POS and V-POS can be automat-
ically adjusted in the VGA/S-VGA/XGA mode.
32
Monitor out check
1) Input the video and audio signals to the
COMPUTER1 and COMPUTER2 ter-
minals.
minals.
2) Connect another monitor to the monitor
out terminal.
3) Connect a speaker with a built-in ampli-
fier to the audio out terminal.
1) Check that image selected with the projector is displayed on
another monitor connected to monitor out terminal and sound is
heard from the speaker connected to the audio out terminal.
heard from the speaker connected to the audio out terminal.
33
RS232C operation
check
check
1) Connect the unit and a PC with the
RS232C cable.
1) Send a command from the PC, and check it functions correctly.
34
USB operation check
1) Connect to a PC with an USB cable.
1) Check that forward/reverse operation is enabled on the PC screen
using the remote control.
35
LAN operation check
1) Connect to a PC with a LAN cable.
1) Check that communication is possible.
36
Remote control check
1) Check the wired remote operation.
2) Check the remote control operation.
2) Check the remote control operation.
1) Check that the wired remote control terminal is activated.
2) Check the remote control operation.
2) Check the remote control operation.
No.
Adjustment Item
Adjustment Conditions
Adjustment Procedures
XG-C330X/C430X
4 – 11
4. Adjustment mode process menu
Adjustment mode process menu
37
Model name check
1) Send “TNAM 1” and “MNRD 1”h with
RS232C command.
1) Check that the appropriate model name is displayed correctly.
38
Delivery settings
1) Make the following settings.
Group
Sub Group
Subject
Adjust DTV image
DTV
Contrast
Tint
Color
Sharpness
Bright
B-DRIVE
R-DRIVE
Tint
Color
Sharpness
Bright
B-DRIVE
R-DRIVE
Adjust DVD image
DVD
Contrast
Tint
Color
Sharpness
Bright
B-DRIVE
R-DRIVE
Tint
Color
Sharpness
Bright
B-DRIVE
R-DRIVE
Adjust Video image
VIDEO
Contrast
N-Tint
P-Tint
S-Tint
N-Color
P-Color
S-Color
Sharpness
Bright
B-DRIVE
R-DRIVE
N-Tint
P-Tint
S-Tint
N-Color
P-Color
S-Color
Sharpness
Bright
B-DRIVE
R-DRIVE
Adjust PC image
AD
R-Bright
G-Bright
B-Bright
R-Contrast
G-Contrast
B-Contrast
G-Bright
B-Bright
R-Contrast
G-Contrast
B-Contrast
Adjust PC image
AD2
R-Bright2
G-Bright2
B-Bright2
R-Contrast2
G-Contrast2
G-Bright2
B-Bright2
R-Contrast2
G-Contrast2
No.
Adjustment Item
Adjustment Conditions
Adjustment Procedures
Destination
Process
Remote control
adjustment
adjustment
USA
SS4
Factory setting at 4
Others
SS3
Factory setting at 3
Click on the first or last page to see other XG-C430X service manuals if exist.