DOWNLOAD Sharp XG-C40XE (serv.man3) Service Manual ↓ Size: 6.34 MB | Pages: 33 in PDF or view online for FREE

1. Connect the oscilloscope to

TP1102 for red.

    TP1202 for green.
    TP1302 for blue.

2. Make the following choice:

Group : OUTPUT 2
Subject : PSIG-H

PSIG-L

3. Using the horizontal 10-step

signal, make sure no vertical
stripes appear every 12 dots.
(If any white or black vertical
stripes appear, finely adjust
the PSIG-L setting.)

»

Adjust the PSIG waveform as shown below.

»

Make sure that the (G) and (B) waveforms are similar
to that of (R).

Adjust the PSIG-H setting.

Adjust the PSIG-L setting.

3.7V   0.1V

2.3V   0.1V

GND

(With XGA signal input)

1. Feed the XGA-mode 75-Hz

black signal.

2. Select the following group

and subjects.
Group  : OUTPUT3
Subject: SH-PHASE,

     GCK-PHASE

»

Make sure that the SH-PHASE and GCK-PHASE
settings are 11 and 6, respectively.

1. Feed the black-and-red

(25%) stripe signal (XGA).

2. Make the following choice:

Group : OUTPUT 3
Subject : RC (R)

»

Using the control switches or the remote controller
buttons, adjust the data in order to minimize the
flicker.

»

Make the same adjustment for BC (B), GC (G).

»

See if the image is equally adjusted at the center
and both sides of the screen. If not, readjust the
setting to have the image equal at right and left.

1. Feed the green-only SMPTE

pattern signal (XGA).
Group : OUTPUT 1
Subject : G1-BLK

»

Adjust the G-BLK data until the gradation of the
portion 

1

 (95% and 100% white) shown below

can be slightly recognized.  Make sure also that the
gradation of the portion 

2

 (0% and 5% black) is

visible.

1. Feed the 32-step gray scale

signal (XGA).
Group : OUTPUT 1
Subject : R1-BLK (R)

B1-BLK (B)

»

Choose the subjects R1-BLK and B1-BLK and
adjust the black balance of the gradation.

1

2

1. Feed the NTSC monoscope

pattern signal.

2. Group : VIDEO 2

Subject : N358-DLY     (4)

N443-DLY     (0)
PAL-DLY       (3)
SECAM-DLY (0)

Make sure the settings are

    as above.
3. Group : VIDEO 1

Subject : NTSC-H

»

Using the control switches or the remote controller
buttons, adjust the data to have the same overscan
in Reft and Right.

2.0Vp-p

1. Feed the split colour bar sig-

nal.
Group : VIDEO 1
Subject : PICTURE

2. Connect the oscilloscope

between pin (2) of P801 and
GND.

»

Using the control switches or the remote controller
buttons, adjust the black-to-white (100%) level
difference to 2.0 

±

0.06 Vp-p.

1. Feed the split colour bar

signal.
Group : VIDEO 1
Subject : TINT

2. Connect the oscilloscope to

pin (4) of P801.

»

Using the control switches or the remote controller
buttons, adjust the data to have the -(B-Y) wave-
form downhill straight.

»

After adjusting, adjust the
value of TINT up 3 point.

1. Feed the split colour bar signal.

Group : VIDEO 1
Subject : AGC

»

Using the control switches or the remote controller
buttons, adjust the setting until the white signal
becomes bit-less.

1. Feed the baseband (split

colour bar) signal. (The ON-
AIR signal is not accepted
because of its too much
noise.)
Group : VIDEO 2
Subject : VROS/VGOS/VBOS

2. Press the control switch or

the remote control’s mute
button (to set the gamma
correction to the process
setting).

»

Using the control switches or the remote controller
buttons, adjust the setting until the black signal
becomes bit-less.

100% White Red

1. Feed the split colour bar sig-

nal.
Group : VIDEO 1
Subject : N-COLOR

2. Connect the oscilloscope to

pin (1) of P801.

»

Using the control switches or the remote controller
buttons, adjust the difference between the 100%
white portion and the red portion to 0.00 

±

0.05 Vp-p.

   (same as 100% white)

100% White Red

100% White Red

1. Feed the PAL colour bar sig-

nal.
Group : VIDEO 1
Subject : P-COLOR

2. Connect the oscilloscope to

pin (1) of P801.

»

Using the control switches or the remote controller
buttons, adjust the difference between the 100%
white portion and the red portion to 0.2 

±

0.05 Vp-p.

1. Feed the SECAM colour bar

signal.
Group : VIDEO 1
Subject : S-COLOR

2. Connect the oscilloscope to

pin (1) of P801.

»

Using the control switches or the remote controller
buttons, adjust the data to have a level difference
of 0.2 

±

0.05 Vp-p between the 100% white portion

and the red portion.

1. Feed the NTSC 10-step sig-

nal.

2. Select the following group

and subject.
Group  :  VIDEO2
Subject: R1-GAIN

B1-GAIN

3. Connect the oscilloscope to

TP1101 (R) and TP1201 (G).

4. For the blue colour, connect

the oscilloscope to TP1301
(B) and TP1201 (G).

»

Select R1-GAIN and adjust the setting so that the
R and G signals have the same amplitude.

»

For the blue colour, adjust the setting the same
way.

1. Feed the NTSC monoscope

pattern signal
Group : VIDEO 2
Subject : R1-BLK

B1-BLK

»

Using the control switches or the remote controller
buttons, adjust so that the entire screen looks
evenly colourless.

1. Feed the monoscope pattern

signal.

2. Group  : DTV

Subject: CR-OFFSET

CB-OFFSET

»

Using the control switches or the remote controller
buttons, adjust so that the entire screen looks
evenly colourless.

1. Group  :  VIDEO1

Subject: SET UP B

SET UP C

»

Make sure the settings are 11 for SET UP B and 2
for SET UP C.

1. Using the colour errugularity

correction system (ccdc),
apply automatic colour
correction.

»

Make sure there is no noticeable colour irregularity
left on the screen.

1. Receive the colour bar sig-

nal.

»

In the process mode and select L1. Check the col-
our and tint.

1. Receive the monoscope pat-

tern signal.

»

In the process mode and select L2. Check the pic-
ture, brightness and sharpness.

»

In the process mode nad select L3. Check the bass,
treble.

1. Receive the RGB signal.

»

In the process mode and select L4. Check the pic-
ture, brightness, red, blue, clock, phase, horizontal
position, and vertical position.

»

In the process mode and select OFF. Make sure that
the off-timer starts with “5” (minutes), counts down each
minute in 1 second, and turns off the set at “0”.

1. Heat the thermistor using a

dryer.

»

Make sure the “TEMP” is displayed.

1. Receive the PHASE check

pattern signal.

»

Call the VGA/SVGA/XGA/SXGA mode and make
sure that the clock, phase, horizontal and vertical
positions can be automatically adjusted.

»

Make sure the keystone correction functions well.

»

Make the following settings.

S3

“Factory setting 3”(XG-C40XE1)

S4

“Factory setting 4”(XG-C40XU1)

Process
adjustment

Remote controller setting