DOWNLOAD Sharp XG-C40XE (serv.man18) Service Manual ↓ Size: 2.5 MB | Pages: 20 in PDF or view online for FREE

Model
XG-C40XE (serv.man18)
Pages
20
Size
2.5 MB
Type
PDF
Document
User Manual / Operation Manual
Brand
Device
Projector / Part 2
File
xg-c40xe-sm18.pdf
Date

Sharp XG-C40XE (serv.man18) User Manual / Operation Manual ▷ View online

Operation
21
Setting up the Screen
Using the Adjustment Foot
You can adjust the height of the image by raising the
projector with the foot release.
1 Press the foot release and lift the projector to the
desired angle. (Adjustable up to approximately
5° from the standard position.)
2 Remove your hand from the foot release. Once
the adjustment foot has locked in position, release
the projector.
3 If the screen is at an angle, the adjuster can be
used to adjust the angle of the image. (Adjustable
up to approximately 1° from the original position.)
1
3
Foot release
Returning the projector to its original position
While holding the projector, press the foot release and slowly lower the projector to its original position.
• When an adjustment is made, the image may become distorted (keystoned), depending on the relative positions of the projector and the
screen.
CAUTION
• Do not press the foot release when the adjustment foot is extended without firmly holding the projector.
• Do not hold the lens when lifting or lowering the projector.
• When lowering the projector, be careful not to get your fingers caught in the area between the adjustment foot and the
projector.
• Optimal image quality can be achieved when the projector is positioned perpendicular to the screen with all feet flat and level.
Reversed Image Setup
Projection using a mirror
• When the distance between the projector and screen
is not sufficient for normal rear projection, you can
use a mirror to reflect the image onto the screen.
• Place a mirror (normal flat type) in front of the lens.
• Project the normal image onto the mirror.
• The image reflected from the mirror is projected onto
the translucent screen.
Rear projection
• Place a translucent screen between the projector and
the audience.
• Use the projector’s menu system to reverse the
projected image. (See page 44 for use of this
function.)
CAUTION
• When using a mirror, be sure to carefully position both the projector and the mirror so the light does not shine into the eyes of
the audience.
Ceiling-mount Setup
• It is recommended that you use the optional Sharp ceiling-
mount bracket for this installation.
• Before mounting the projector, contact your nearest Sharp
Authorised LCD Projector Dealer or Service Centre to obtain
the recommended ceiling-mount bracket (sold separately).
(AN-C30T ceiling-mount bracket, AN-TK201/202 extension
tube for AN-C30T.)
• When the projector is in the inverted position, use the upper
edge of the screen as the base line.
• Use the projector’s menu system to select the appropriate
projection mode. (See page 44 for use of this function.)
XG-C40XE/CD (E)-c
01.8.1, 5:52 PM
21
Operation
22
Setting up the Screen
Projector
Digital Image Adjustments
Digital Keystone Correction
Remote control
When the image is distorted due to the projection angle,
the Digital Keystone Correction function allows you to
correct it.
2
3
1, 4a
4b
2
2
2
2
Test Pattern
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1
Press  KEYSTONE to select mode. Each time
KEYSTONE is pressed, the screen changes as
shown on the left.
2
Press ENTER to display test pattern.
3
Press 
/ƒ/ß/©
 to make adjustments.
4
a. Press  KEYSTONE until normal screen
appears.
b. To reset the KEYSTONE setting, press UNDO.
Digital Shift
or
Press ∂.
Press ƒ.
Pressing ƒ
ƒ
ƒ
ƒ
ƒ
in Step 2
Pressing 
in Step 2
Digital Keystone Correction
• Straight lines and the edges of the displayed image may
appear jagged, when adjusting the KEYSTONE setting.
Digital Shift
When a WIDE or NORMAL (WIDE) image is projected,
this function can be used to shift the image up or down.
(Slide the MOUSE/ADJUSTMENT switch
on the remote control to the ADJ. position.)
MOUSE
ADJ.
1
Press KEYSTONE to select “DIGITAL SHIFT” as
shown on the near left.
2
Press ENTER to display test pattern.
3
Press 
/ƒ/ß/©
 to make adjustments.
4
a. Press  KEYSTONE until normal screen
appears.
b. To reset the DIGITAL SHIFT setting, press
UNDO.
• This function only works with WIDE and NORMAL (WIDE)
picture display modes during video or DTV input. (See page
38 for details.) The DIGITAL SHIFT screen is not displayed
when projecting images other than WIDE or NORMAL
(WIDE).
On-screen Display
(Example:
16:9 WIDE image)
On-screen Display
(Example:
4:3 NORMAL image)
XG-C40XE/CD (E)-c
01.8.1, 5:52 PM
22
Operation
23
MOUSE
ADJ.
MOUSE/ADJUSTMENT switch
(Remote control)
MOUSE
ADJ.
Using the Wireless Mouse
Remote control
Using the Remote Control as a 
Wireless Mouse
Remote Control/Mouse Receiver Positioning
The remote control has the following three functions:
• Projector control
• Wireless mouse
• Laser pointer
• The remote control can be used to control the projector within the ranges shown below.
• The remote mouse receiver can be used with the remote control to control the mouse functions of a connected
computer within the ranges shown below.
• The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the
signal may differ due to the screen material.
Wireless mouse
Laser pointer
Projector control
Operating the Wireless Mouse from the Remote Control
Controlling the Projector
Remote control
Remote control
4 m
30˚
30˚
120˚
Remote
mouse
receiver
30˚
45˚
7 m
30˚
30˚
45˚
XG-C40XE/CD (E)-c
01.8.1, 5:52 PM
23
Operation
24
Operating the Wireless Mouse from the Remote Control
Use as a Wireless Mouse
Be sure the supplied remote mouse receiver is
connected to your computer.
(Slide the MOUSE/ADJUSTMENT switch on
the remote control to the MOUSE position.)
• The wireless mouse may not operate correctly if your
computer serial port is not correctly set up. Refer to the
computer’s operation manual for details of setting up/
installing the mouse driver.
• For one-button mouse systems, use either the LEFT-CLICK
or RIGHT-CLICK button.
Using the remote control in a dark room
Press  BACKLIGHT, and the buttons will lilluminate.
Green lights refer to mouse operations, and red lights
to projector adjustments.
Position of MOUSE/ADJUSTMENT switch
MOUSE 
LASER POINTER (GREEN)
BLACK SCREEN (GREEN)
RIGHT-CLICK (GREEN)
MOUSE (NOT LIT)
ON (NOT LIT)
ADJ. 
MENU (RED)
KEYSTONE (RED)
ENTER (RED)
ADJUSTMENT (NOT LIT)
Button name
LASER POINTER/MENU
BLACK SCREEN/KEYSTONE
RIGHT-CLICK/ENTER
MOUSE/ADJUSTMENT
LEFT-CLICK
POWER ON/OFF
VOLUME 
Ⳮ/ⳮ
MUTE
INPUT
UNDO
FREEZE
AUTO SYNC
ENLARGE
RESIZE
TOOLS
GAMMA
Use as a Laser Pointer
(Slide the MOUSE/ADJUSTMENT switch on
the remote control to the MOUSE position.)
Press  LASER POINTER (
) to activate the laser
pointer. When the button is released, the light
automatically goes off.
• For safety, the laser pointer automatically goes off after 1
minute of continuous use. To turn it on, release LASER
POINTER
 (
) and press again.
MOUSE
ADJ.
Effective buttons in MOUSE mode
Remote control
(Front view)
Remote control
(Rear view)
LASER POINTER
BLACK SCREEN
MOUSE
RIGHT-CLICK
BACKLIGHT
LEFT-CLICK
MOUSE
ADJ.
ON (RED)
XG-C40XE/CD (E)-c
01.8.1, 5:52 PM
24
Page of 20
Display

Sharp XG-C40XE (serv.man18) User Manual / Operation Manual ▷ Download

  • DOWNLOAD Sharp XG-C40XE (serv.man18) Service Manual ↓ Size: 2.5 MB | Pages: 20 in PDF or view online for FREE
  • Here you can View online or download the User Manual / Operation Manual for the Sharp XG-C40XE (serv.man18) in PDF for free, which will help you to disassemble, recover, fix and repair Sharp XG-C40XE (serv.man18) Projector. Information contained in Sharp XG-C40XE (serv.man18) User Manual / Operation Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.