DOWNLOAD Sharp XG-C330X (serv.man2) Service Manual ↓ Size: 6.41 MB | Pages: 71 in PDF or view online for FREE

1

1

1

1

1 Setting a Password

Select “Password”, then press |

|

|

|

|.

• The screen for entering the password is displayed.

Press '

'

'

'

' or "

"

"

"

" to set the first digit in

“New Password” and then press |

|

|

|

|.

Note

• Once the password is set, you must enter the

password to change the “Options2” menu set-
tings.

Select “Password”, then press |

|

|

|

|.

• The screen for entering the password appears.

Enter the password in “Old Pass-
word”  using  '

'

'

'

',  "

"

"

"

",  |

|

|

|

|  and  \

\

\

\

\,  then

Enter the password in “New Pass-
word” using  '

'

'

'

', "

"

"

"

", |

|

|

|

| and \

\

\

\

\, then

Enter the same password again in
“Reconfirm” using '

'

'

'

', "

"

"

"

", |

|

|

|

| and \

\

\

\

\,

Note

• If you do not need the password protection for

the “Options2” menu settings anymore, press

ENTER without entering a new password in

steps 3 and 4.

• To cancel the password settings, press 

RE-

TURN.

Note

• If 

ENTER is held down for more than 5 seconds,

the operation buttons on the projector will be locked.
(See page 

• You cannot use the buttons on the remote control to

delete the password.

Options2
Password
Speaker
Audio Out
PRJ Mode
Fan Mode
Monitor Out
LAN/RS232C
RS-232C
DHCP Client
TCP/IP
MAC Address
Projector

All Reset

COMP.1

Disable
On
FAO
Front
Normal
Enable
Enable
9600 bps
On

08:00:1F:B1:B7:74
MYPROJECTOR

SEL./ADJ.
RETURN

ENTER
END

1
2
3
4
5
6
7
8
9
0
q

w

8

8

8

8

8 Selecting the Transmis-

Description

Transmission speed is slow.

Transmission speed is rapid.

Selectable items

9600 bps

38400 bps

115200 bps

Note

• Refer to the “SETUP MANUAL” contained on

the supplied CD-ROM for RS-232C Specifica-
tions and Command Settings.

• Refer to the computer’s operation manual for

instructions for setting the computer’s baud rate.

2

2

2

2

2 Speaker Setting

Selectable items

On

Off

Description

The audio signal is output from the internal
speaker.
The audio signal is not output from the
internal speaker.

3

3

3

3

3 Audio Output Type Setting

• When “Audio Out” has been set to “VAO”, first make

sure to lower the volume of the projector before
turning the power on or off and when switching the
input.

Description

Audio output that does not vary in
strength with the volume level of the
source projector.
Audio output that varies in strength with
the volume level of the source projector.

Selectable items
FAO
(Fixed Audio
Output)
VAO
(Variable
Audio Output)

4

4

4

4

4 Reversing/Inverting Pro-

Note

• This function is used for the reversed image and

5

5

5

5

5 Fan Mode Setting

Description

Suitable for normal environments.
Select this when using the projector at
altitudes of approximately 1,500 meters
(4,900 feet) or more.

Selectable items
Normal
High

When “Fan Mode” is set to “High”, the fan rotation
speeds up, and the fan noise becomes louder.

6

6

6

6

6 Monitor Output
7

7

7

7

7 LAN/RS232C

Description

The function is activated even if the
projector is in standby mode.
The function is switched off when the
projector is in standby mode.

Selectable items
Enable

Disable

Note

• When you want to control the projector using

the LAN/RS232C function, select “Enable”.

Description

Normal image (Projected from the front
of the screen)

Inverted image (Projected from the
front of the screen with an inverted
projector)

Reversed image (Projected from the
rear of the screen or with a mirror)

Reversed and inverted image (Pro-
jected with a mirror)

Selectable items

Front

Ceiling + Front

Rear

Ceiling + Rear

9

9

9

9

9 DHCP Client Setting

Select “On” for “DHCP Client”, then press 

ENTER

.

“Obtaining IP Address...” appears, then the menu
screen appears. Confirm the parameters of IP
Address, Subnet Mask and Gateway on the TCP/IP
screen.
If the DHCP server is not available, “Could not
obtain IP Address.” appears.
In this case, set the TCP/IP manually. (See the
item 0.)

Selectable items
On

Off

Description

Obtains configuration parameters for
TCP/IP network automatically.
Sets the TCP/IP manually.

0

0

0

0

0 TCP/IP Setting

Enter “IP Address” using '

'

'

'

', "

"

"

"

", |

|

|

|

|

and \, then press 

Enter “Subnet Mask” using '

'

'

'

', "

"

"

"

",

|

|

|

|

| and \, then press  ENTER.

Enter “Gateway” using '

'

'

'

', "

"

"

"

", |

|

|

|

| and

\, then press  ENTER.

Selectable items
IP Address

Subnet Mask

Gateway

Description

Factory default setting:
192.168.150.002
Enter an IP address appropriate for the
network.
Factory default setting:
255.255.255.000
Set the subnet mask to the same as
that of the computer and equipment on
the network.
Factory default setting:
000. 000. 000. 000
* When not in use, set to:
  “000. 000. 000. 000”.

Note

• Confirm the existing network’s segment (IP ad-

dress group) to avoid setting an IP address that
duplicates the IP addresses of other network
equipment or computers. If “192.168.150.002”
is not used in a network with an IP address of
“192.168.150.XXX”, you don’t have to change
the projector IP address.

• For details about each setting, consult your

network administrator.

q

q

q

q

q

w

w

w

w

w

Displayed items

MAC Address

Projector

Description

The MAC address of the projector is
displayed.
The projector name is displayed.

Note

• For information on how to change the projector

name, see “SETUP MANUAL” contained in the
supplied CD-ROM.

Note

The following items or menu cannot be initialized.
• “Fine Sync” menu

Resolution

• “Options1” menu

Lamp Timer (Life)
System Lock

• “Language” menu

Language

COMP.1

SEL./ADJ.
RETURN

ENTER
END

English
Deutsch
Español
Nederlands
Français
Italiano
Svenska
Português