DOWNLOAD Sharp PG-MB60X (serv.man6) Service Manual ↓ Size: 65.51 KB | Pages: 4 in PDF or view online for FREE

Model
PG-MB60X (serv.man6)
Pages
4 Few pages! See other manuals at the bottom of the first or last page.
Size
65.51 KB
Type
PDF
Document
Service Manual
Brand
Device
Projector / p6-10 Notice to Service Personel
File
pg-mb60x-sm6.pdf
Date

Sharp PG-MB60X (serv.man6) Service Manual ▷ View online

6
PG-MB60X
NOTE POUR LE PERSONNEL
D’ENTRETIEN
 PRECAUTION POUR LES RADIATIONS UV
La source de lumière, la lampe UHP, dans le projecteur
LCD émet de petites quantités de radiation UV.
EVITEZ TOUTE EXPOSITION DIRECTE DES
YEUX ET DE LA PEAU.
Pour votre sécurité, nous vous prions de respecter
les points suivants:
1. Toujours porter des lunettes de soleil lors d’un entretien
du projecteur
avec la lampe allumée
et le haut du coffret retiré.
2. Ne pas faire fonctionner la lampe à l’extérieur du boîtier
de lampe.
3. Ne pas faire fonctionner plus de 2 heures avec le coffret
retiré.
Précautions pour les radiations UV
et la lampe moyenne pression
1. Toujours débrancher la fiche AC lors du remplacement
de la lampe.
2. Laisser l’unité refroidir pendant une heure avant de
procéder à l’entretien.
3. Ne remplacer qu’avec une lampe du même type.  Type
AN-MB
6
0LP, caractéristique 275W.
4. La lampe émet de petites quantités de radiation UV-
éviter tout contact direct avec les yeux.
5. La lampe moyenne pression implique un risque
d’explosion. Toujours suivre les instr uctions
d’installation décrites ci-dessous et manipuler la lampe
avec soin.
NOTE TO  SERVICE
PERSONNEL
 UV-RADIATION PRECAUTION
The light source,  UHP lamp,  in the LCD projector
emits small amounts of UV-Radiation.
AVOID DIRECT EYE AND SKIN EXPOSURE.
To ensure safety please adhere to the following:
1. Be sure to wear sun-glasses when servicing the
projector with the lamp
turned “on” and the top
enclosure removed.
2. Do not operate the lamp outside of the lamp housing.
3. Do not operate for more than 2 hours with the enclosure
removed.
UV-Radiation and Medium Pressure
Lamp Precautions
1. Be sure to disconnect the AC plug when replacing the
lamp.
2. Allow one hour for the unit to cool down before
servicing.
3. Replace only with same type lamp. Type AN-MB
6
0LP
rated 275W.
4. The lamp emits small amounts of UV-Radiation,  avoid
direct-eye contact.
5. The medium pressure lamp involves a risk of explosion.
Be sure to follow installation instructions described
below and handle the lamp with care.
123456789012345678901234567890121234567890123456
123456789012345678901234567890121234567890123456
123456789012345678901234567890121234567890123456
123456789012345678901234567890121234567890123456
123456789012345678901234567890121234567890123456
123456789012345678901234567890121234567890123456
123456789012345678901234567890121234567890123456
123456789012345678901234567890121234567890123456
7
PG-MB60X
Remplacement de la lampe
Remarque:
Comme la lampe devient très chaude pendant le
fonctionnement de l’unité, son remplacement ne doit
être effectué au moins une heure après avoir coupé
l’alimentation (pour permettre à la lampe de refroidir).
En installant la nouvelle lampe, s’assurer de ne pas
toucher la lampe (ampoule).  Remplacer la lampe en
tenant son réflecteur  
2
.
[N’utiliser qu’un remplacement d’origine.]
123456789012345678901234567890121234567890123456
123456789012345678901234567890121234567890123456
123456789012345678901234567890121234567890123456
123456789012345678901234567890121234567890123456
123456789012345678901234567890121234567890123456
123456789012345678901234567890121234567890123456
1
2
Lamp
Reflector
Comme de petites quantités de radiation UV sont
émises par une ouverture entre les ventilateurs as-
pirants, il est recommandé de placer le capuchon de
l’optique optionnelle sur l’ouverture pendant l’entretien
pour éviter une exposition des yeux et la peau.
Since small amounts of UV-radiation are emitted
from an opening between the exhaust fans, it is rec-
ommended to place the cap of the optional lens on
the opening during servicing to avoid eye and skin
exposure.
DANGER !  –– Never turn the power on without the
lamp to avoid electric-shock or damage of the devices
since the stabilizer generates high voltages at its start.
UV-RADIATION PRECAUTION (Continued)
Lamp Replacement
Note:
Since the lamp reaches a very high temperature during
units operation replacement of the lamp should be
done at least one hour after the power has been turned
off.  (to allow the lamp to cool off.)
Installing the new lamp, make sure not to touch the
lamp (bulb) replace the lamp by holding its reflector
2
.
[Use original replacement only.]
DANGER !  –– Ne jamais mettre sous tension sans la
lampe pour éviter un choc électrique ou des
dommages des appareils car le stabilisateur génère
de hautes tensions à sa mise en route.
123456789012345678901234567890121234567890123456
123456789012345678901234567890121234567890123456
123456789012345678901234567890121234567890123456
123456789012345678901234567890121234567890123456
123456789012345678901234567890121234567890123456
123456789012345678901234567890121234567890123456
1
2
PRECAUTION POUR LES RADIATIONS UV (Suite)
Lampe
Reflecteur
8
PG-MB60X
WARNING:
High brightness light source,  do not stare into the beam of light,  or view directly.  Be especially
careful that children do not stare directly in to the beam of light.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,  DO NOT EXPOSE THIS UNIT TO
MOISTURE OR WET LOCATIONS.
CAUTION:   TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE CABINET.
NO USER-SERVICEABLE PARTS  EXCEPT LAMP UNIT.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lighting flash with arrowhead within a
triangle is intended to tell the user that
parts inside the product are risk of electric
shock to persons.
The exclamation point within a triangle is
intended to tell the user that important
operating and servicing instructions are in
the manual with the projector.
CAUTION
AVERTISSEMENT:
Source lumineuse de grande intensité.  Ne pas fixer le faisceau lumineux ou le regarder
directement.  Veiller particulièrement à éviter que les enfants ne fixent directement le
faisceau lumineux.
AVERTISSEMENT:
AFIN D’EVITER TOUT RISQUE D’INCENDIE OU D’ELECTROCUTION,  NE PAS PLACER
CET APPAREIL DANS UN ENDROIT HUMIDE OU MOUILLE.
L’éclair terminé d’une flèche à l’intérieur
d’un triangle indique à l’utilisateur que les
pi‘eces se trouvant dans l’appareil sont
susceptibles de provoquer une décharge
électrique.
Le point d’exclamation à l’intérieur d’un
triangle indique à l’utilisateur que les
instructions de fonctionnement et
d’entretien sont détaillées dans les
documents fournis avec le projecteur.
RISQUE
D’ÉLECTROCUTION. NE
PASR ETIRER LES VIS Á
 L’EXCEPTION DE LA VIS DE
REPARATION UTILISATEUR
SPECIFIEES
ATTENTION
ATTENTION:  POUR EVITER TOUT RISQUE
D’ELECTROCUTION,  NE PAS RETIRER LE CAPOT.
AUCUNE DES PIECES INTERIEURES N’EST REPARABLE
PAR L’UTILISATEUR, A L’EXCEPTION DE L’UNITE DE
LAMPE.  POUR TOUTE REPARATION,  S’ADRESSER A UN
TECHNICIEN D’ENTRETIEN QUALIFIE.
RISK OF ELECTRIC SHOCK.
DO NOT REMOVE SCREWS
EXCEPT SPECIFIED USER
SERVICE SCREW.
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
CAUTION
(POWER Unit)
6.3A 250V
For continued
protection against a
risk of fire,  replace
only with same type
6.3A, AC250V fuse.
(F701)
PRECAUTION
(Unité de PUTSSANCE)
Pour une protection
continue contre un
risques d’incendie,  ne
remplacer qu’avec un
fusible 6.3A,AC250V
 du même type.
(F701)
6.3A 250V
10
PG-MB60X
Precautions for using lead-free solder
1 Employing lead-free solder
"PWBs" of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the
PWBs and service manuals. The alphabetical character following LF shows the type of lead-free solder.
Example:
2 Using lead-free wire solder
When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional
lead wire solder may cause damage or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40°C, we recommend you
to use a dedicated soldering bit, if you are not familiar with how to obtain lead-free wire solder or soldering bit,
contact our service station or service branch in your area.
3 Soldering
As the melting point of lead-free solder (Sn-Ag-Cu) is about 220°C which is higher than the conventional lead solder
by 40°C, and as it has poor solder wettability, you may be apt to keep the soldering bit in contact with the PWB for
extended period of time. However, since the land may be peeled off or the maximum heat-resistance temperature of
parts may be exceeded, remove the bit from the PWB as soon as you confirm the steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on
and off the power of the bit as required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after
every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
Be careful when replacing parts with polarity indication on the PWB silk.
L
F a
Indicates lead-free solder of tin, silver and copper.
Part No.
Description
Code
ZHNDAi123250E
J
φ
0.3mm
250g(1roll)
BL
ZHNDAi126500E
J
φ
0.6mm
500g(1roll)
BK
ZHNDAi12801KE
J
φ
1.0mm
1kg(1roll)
BM
Lead-free wire solder for servicing
Display

Sharp PG-MB60X (serv.man6) Service Manual ▷ Download

  • DOWNLOAD Sharp PG-MB60X (serv.man6) Service Manual ↓ Size: 65.51 KB | Pages: 4 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sharp PG-MB60X (serv.man6) in PDF for free, which will help you to disassemble, recover, fix and repair Sharp PG-MB60X (serv.man6) Projector. Information contained in Sharp PG-MB60X (serv.man6) Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.