Sharp PG-M25XE (serv.man30) User Manual / Operation Manual ▷ View online
Basic Operation
Basic Operation
Image Projection
▼Projector indicators
LAMP REPLACEMENT indicator
POWER indicator
POWER button
INPUT
button
button
INPUT button
POWER button
▼Keycode input box
-34
Volume
buttons
buttons
Volume button
Basic Procedure
Connect the required external equipment to the pro-
jector before operating the following procedures.
Details are found in the projector operation manual.
jector before operating the following procedures.
Details are found in the projector operation manual.
Info
• The language preset at the factory is English.
If you want to change the on-screen display
to another language, reset the language ac-
cording to the procedure on
to another language, reset the language ac-
cording to the procedure on
page 37
.
1
Plug the power cord into the wall outlet.
• The POWER indicator illuminates up in red,
and the projector enters standby mode.
2
Press
on the projector or
on the GyroRemote.
• The POWER indicator illuminates in
green. After the LAMP REPLACEMENT
indicator illuminates, the projector is
ready to start operation.
indicator illuminates, the projector is
ready to start operation.
Note
• The LAMP REPLACEMENT indica-
tor illuminates, indicating the status
of the lamp.
of the lamp.
Green: The lamp is ready.
Green blinking: The lamp is
Green blinking: The lamp is
warming up.
Red blinking: The lamp should
be replaced soon.
Red: The lamp should be
replaced immediately.
• If the power is turned off and imme-
diately switched on again, the LAMP
REPLACEMENT indicator may take
time to illuminate.
REPLACEMENT indicator may take
time to illuminate.
3
When “Anti-Theft” (see
page 102
) is
set, the keycode input box will appear.
• Enter the keycode.
Note
• When entering the keycode, press
the buttons previously set on the
projector or the GyroRemote.
projector or the GyroRemote.
Info
• When “Anti-Theft” is set, enter the
keycode or the input display will not ap-
pear. Even when the signal is input, the
display will not appear. (See
pear. Even when the signal is input, the
display will not appear. (See
page 102
.)
Basic Operation
-35
"On-screen Display (Example)
Using
Analog RGB
Analog RGB
Using
Component
Component
INPUT 2 Mode
INPUT 3 Mode
4
Press
and select the input
mode.
• Each press switches in the following
order:
→ INPUT 1 → INPUT 2 → INPUT 3 → INPUT 4
• You can also use the
on the
GyroRemote.
Note
• When no signal is received, “NO SIG-
NAL” will be displayed. When a signal
that the projector is not preset to
receive is input, “NOT REG.” will be
displayed.
that the projector is not preset to
receive is input, “NOT REG.” will be
displayed.
• When Auto Search is ON, the input
modes with signals can be selected
(See
(See
page 90
.)
• When a PC card is inserted, the input
will automatically change to INPUT 4.
• You can select the input mode directly
by using the Button Assign function
on the GyroRemote (See
on the GyroRemote (See
page 41
.)
About the INPUT Modes
Used for projecting images
from equipment that sends
RGB signals or Component
signals connected to the DVI-
DIGITAL/ANALOG input port.
Used for projecting images
from equipment connected to
the S-VIDEO input terminal.
Used for projecting images
from equipment connected to
the VIDEO input terminal.
When projecting from a wire-
less LAN PC card or a
memory card.
from equipment that sends
RGB signals or Component
signals connected to the DVI-
DIGITAL/ANALOG input port.
Used for projecting images
from equipment connected to
the S-VIDEO input terminal.
Used for projecting images
from equipment connected to
the VIDEO input terminal.
When projecting from a wire-
less LAN PC card or a
memory card.
INPUT 1
(RGB/
Component)
(RGB/
Component)
INPUT 2
(S-Video)
(S-Video)
INPUT 3
(Video)
(Video)
INPUT 4
(PC Card)
(PC Card)
INPUT 1 Mode
5
Press
or
on the projector
to adjust the volume.
Note
• Pressing “+” will raise the volume.
Pressing “–” will lower the volume.
• On the GyroRemote, the volume can
be adjusted by pressing
.
• When a PC card is installed,
,
on the projector or
on the
GyroRemote operate as cursor
buttons (\, |) when the OSD menu
is active.
buttons (\, |) when the OSD menu
is active.
Using
DVI digital
DVI digital
Using S-Video
Using Video
INPUT 4 Mode
Memory card installed
• Transmission will be stopped if the input
is switched when a wireless LAN PC
card is installed in INPUT 4 and the
projector is connected to a computer.
card is installed in INPUT 4 and the
projector is connected to a computer.
Image Projection (cont.)
6
Press
on the projector to
temporarily turn off the picture
and sound.
and sound.
Note
• Pressing
again will turn the pic-
ture and the sound back on.
• When using the GyroRemote, you
can select AV MUTE using the
Button Assign function (see
Button Assign function (see
page 41
.)
• If you want to temporarily mute the
sound using the GyroRemote,
select MUTE using the Button
Assign function (see
select MUTE using the Button
Assign function (see
page 41
.)
7
Press
on the projector or
on the GyroRemote .
When the confirmation screen
is displayed, press
is displayed, press
or
once again.
Note
• If you accidentally pressed
or
and do not want to turn off
the power, wait until the confirma-
tion message disappears.
tion message disappears.
Info
• Do not unplug the power cord dur-
ing projection or cooling fan opera-
tion. This can cause damage due to
the rise in internal temperature, as
the cooling fan also stops.
tion. This can cause damage due to
the rise in internal temperature, as
the cooling fan also stops.
• When connected to equipment such
as an amplifier, be sure to turn off
the power to the equipment con-
nected first and then to the projector.
the power to the equipment con-
nected first and then to the projector.
-36
POWER button
MENU
button
button
Volume
buttons
buttons
AV MUTE
button
button