DOWNLOAD Sharp PG-B10S Service Manual ↓ Size: 979.35 KB | Pages: 49 in PDF or view online for FREE

Model
PG-B10S
Pages
49
Size
979.35 KB
Type
PDF
Document
Handy Guide
Brand
Device
Projector / Version 1.5
File
pg-b10s.pdf
Date

Sharp PG-B10S Handy Guide ▷ View online

Warranty Procedure
Version 1.5
Issue 04/2006
7
SHARP ELECTRONICS (UK) LTD
PROJECTOR TECHNICAL SUPPORT
TECHNICAL SERVICES GROUP
Geographical Areas Covered
UK; Republic of Ireland
Warranty Service Arrangements
3-years standard
The approved service company will collect the product from the end-user, repair & return to the
end-user under warranty.
Lamp Warranty Service Arrangements
90-days standard
The end-user returns the faulty lamp and lamp warranty claim form (Provided with the
projector) to the approved service company who will inspect and replace under warranty.
Approved Service Companies:
Sharpserv
County Estate
Nunn Brook Rd
Huthwaite
Notts
NG17 2HU
Tel: 0870 738 00 00
Fax: 0870 738 09 09
E-mail: 
Internet: 
www.sharpserv.co.uk
Maintenance Indicators
Version 1.5
Issue 04/2006
8
SHARP ELECTRONICS (UK) LTD
PROJECTOR TECHNICAL SUPPORT
TECHNICAL SERVICES GROUP
• 
The warning lights on the projector indicate problems inside the projector.
• 
If a problem occurs, either the temperature warning indicator or the lamp replacement
indicator will illuminate red, and the power will turn off. After the power has been turned
off, follow the procedures given below.
 
About the temperature warning
indicator
About the lamp replacement
indicator
If the temperature inside the projector increases, due
to blockage of the air vents, or the setting location,
“TEMP ” will blink in the lower left corner of the
picture. If the temperature keeps on rising, the lamp
will turn off and the temperature warning indicator
will blink, the cooling fan will run for further 90
seconds, then the power will be shut off. After
“TEMP” appears, be sure to perform the following
measures.
• 
The lamp life becomes 0%, when used for
approximately 4,000 hours with “Eco Mode” or
when used for approximately 2,000 hours with
“Standard Mode”.
• 
When the remaining lamp life becomes 5% or
less, “Lamp Warning Icon” will be displayed on
the screen in yellow. When the percentage
becomes 0%, “Lamp Warning Icon” will change
to “Lamp Warning Icon” (red), the lamp will
automatically turn off and then the projector as
well. At this time, the lamp replacement indicator
will illuminate in red.
• 
If you try to turn on the projector a fourth time
without replacing the lamp, the projector will not
turn on.
Maintenance Indicators
Version 1.5
Issue 04/2006
9
SHARP ELECTRONICS (UK) LTD
PROJECTOR TECHNICAL SUPPORT
TECHNICAL SERVICES GROUP
Maintenance indicator
Normal
Abnormal
Condition
Problem
Possible Solution
• 
Blocked air intake
• 
Relocate the
projector to an
area with proper
ventilation.
Temperature
warning
indicator
Off
Red on/
Power off
The internal
temperature is
abnormally high.
• 
Cooling fan breakdown
• 
Internal circuit failure
• 
Clogged air intake
• 
Take the projector
to your nearest
Sharp Authorised
Projector Dealer or
Service Centre
Red blinks/
Red on
Time to change the
lamp
• 
Remaining lamp life
becomes 5% or under.
Lamp
replacement
indicator
Green on
• 
Green
blinks
when
the
lamp is
active.
Red on/
Power off
The lamp does not
illuminate.
• 
Burnt-out lamp
• 
Lamp circuit failure
• 
Carefully replace
the lamp. Take the
projector to your
nearest
• 
Sharp Authorised
Projector Dealer or
Service Centre for
repair.
• 
Please exercise
care
Power
indicator
Green on/
Red on
Red blinks
The power indicator
blinks in red when
the projector is on.
• 
The filter cover, lamp unit
cover or lens cover is
open.
• 
Securely install the
covers.
• 
If the power
indicator blinks
even when the
filter cover is
securely installed,
contact your
nearest Sharp
Authorised
Projector Dealer or
Service Centre for
advice.
Important Information
• 
If the temperature warning indicator illuminates, and the power turns off, follow the above possible
solutions and then wait until the projector has cooled down completely before plugging in the power
cord and turning the power back on. (At least 5 minutes.)
• 
If the power is turned off and then turned on again, as during a brief test, the lamp replacement
indicator may be triggered, preventing the power from going on. Should this occur, take the power
cord out of the wall outlet and plug it back in again.
• 
If you want to clean the air vents during projector operation, be sure to first press “OFF”  on the
projector or “OFF” on the remote control and after the power has turned off and the cooling fan has
stopped, then clean the vents.
• 
Do not unplug the power cord after the power has been turned off and while the cooling fan is
running. The cooling fan runs for about 90 seconds.
Lamp Replacement Procedure
Version 1.5
Issue 04/2006
10
SHARP ELECTRONICS (UK) LTD
PROJECTOR TECHNICAL SUPPORT
TECHNICAL SERVICES GROUP
Lamp
• 
It is recommended that the lamp (sold separately) be replaced when the remaining lamp life
becomes 5% or less, or when you notice a significant deterioration in the picture and colour quality.
The lamp life (percentage) can be checked with the on-screen display. 
• 
For lamp replacement, please consult your nearest Sharp Authorised Projector Dealer or Service
Centre.
Caution Concerning the Lamp
• 
This projector utilises a pressurised mercury lamp. A loud sound may indicate lamp failure. Lamp
failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface
scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure
largely varies depending on the individual lamp and/or the condition and the frequency of use. It is
important to note that failure can often result in the bulb cracking.
• 
When the lamp replacement indicator and on-screen display icon are illuminated or flash, it is
recommended that the lamp be replaced with a new one immediately, even if the lamp appears to
be operating normally.
• 
Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the
lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes
mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In
case of exposure to the gas, consult with a doctor as soon as possible.
• 
Should the lamp break, there is also a possibility that glass particles may spread inside of the
projector. In such a case, it is recommended you contact your nearest Sharp Authorised Projector
Dealer or Service Centre to remove the damaged lamp and assure safe operation.
Replacing the Lamp
*Caution*
• 
Do not remove the lamp unit immediately after operation of the projector. The lamp will be
hot and touching it can lead to burn or injury.
• 
Wait at least one hour after the power cord is disconnected to allow the surface of the
lamp unit to fully cool before removing the lamp unit.
• 
If the new lamp does not light after replacement, take your projector to the nearest Sharp
Authorised Projector Dealer or Service Centre for repair. Purchase a replacement lamp
unit of type BQC-PGB10S//1 from your nearest Sharp Authorised Projector Dealer or
Service Centre. Then carefully change the lamp by following the instructions described in
this section. If you wish, you may have the lamp replaced at your nearest Sharp
Authorised Projector Dealer or Service Centre.
Part Number
Description
Price Rank
PFILDA010WJZZ
Air Filter
AD
BQC-PGB10S//1
Lamp Module
CF
Page of 49
Display

Click on the first or last page to see other PG-B10S service manuals if exist.