Sharp PG-A10XA (serv.man2) Service Manual ▷ View online
29
PG-A10X-A
Process menu1
Adjustment Process Menu
First layer
DTV
Pedestal
DVD
VERSION
VIDEO
SS
AD
TEMP
OUTPUT1
PATTERN
OUTPUT2
LAMP
OUTPUT3
LINE
VIDEO1
EXIT
second layer
Initial Value
DTV
Contrast
2
Tint
5
Color
8
Sharpness
1
CTI-Level
1
LTI-Level
0
CB-Offset
7
CR-Offset
7
Bright
12
B-DRIVE
41
R-DRIVE
41
EXIT
DVD
Contrast
1
Tint
5
Color
5
Sharpness
3
CTI-Level
1
LTI-Level
0
CB-Offset
7
CR-Offset
7
Bright
13
B-DRIVE
41
R-DRIVE
41
EXIT
VIDEO
Contrast
0
N-Tint
5
P-Tint
5
S-Tint
5
N-Color
5
P-Color
5
S-Color
5
Sharpness
3
CTI-Level
1
LTI-Level
0
CB-Offset
7
VIDEO
CR-Offset
7
Bright
13
B-DRIVE
41
R-DRIVE
41
EXIT
AD
R-Bright
63
G-Bright
63
B-Bright
63
R-Contrast
172
G-Contrast
172
B-Contrast
172
EXIT
OUTPUT1
R1-BLK
200
R1-GAIN
166
G1-BLK
200
G1-GAIN
166
B1-BLK
200
B1-GAIN
166
S-R1-BLK
200
S-R1-GAIN
166
S-G1-BLK
200
S-G1-GAIN
166
S-B1-BLK
200
S-B1-GAIN
166
EXIT
OUTPUT2
PSIG-H
90
PSIG-L
16
VCENTER
34
VS-ON
0
VS-POS
0
VS-DAT
0
VS-GDAT1
64
VS-GDAT2
128
VS-GDAT3
192
EXIT
OUTPUT3
RC
90
GC
90
BC
90
GCK-PHASE
8
CC
0
OPT-MECH
0
DFT-SET
1
R-HPC-DAT
321
G-HPC-DAT
321
B-HPC-DAT
321
EXIT
VIDEO1
N-Contrast
14
P-Contrast
14
S-Contrast
15
Color
17
NT3.58 Delay
1
NT4.43 Delay
1
PAL Delay
1
SECAM Delay
3
EXIT
30
PG-A10X-A
Process menu2
Pedestal
R-Bright
-10
G-Bright
-10
B-Bright
-10
R-Contrast
+10
G-Contrast
+10
B-Contrast
+10
EXIT
VERSION
Build
Boot Code
Config
Rom Code
GUI
EXIT
Boot Code
Config
Rom Code
GUI
EXIT
SS
SS2
SS3 EU
SS4 US
SS5 JPN
SS6 CHIN
EXIT
SS3 EU
SS4 US
SS5 JPN
SS6 CHIN
EXIT
TEMP
Temp1
Parameter of sensor 1
Temp2
Parameter of sensor 2
Temp3
No Use
Temp4
No Use
EXIT
PATTERN
Cross Hatch
Color Bar
EXIT
Color Bar
EXIT
LAMP
Current Time
Current time of use
History1
One earlier
History2
Two earlier
History3
Three earlie
History4
Four earlier
TOTAL TIME
Total operating hours
EXIT
LINE
OFF
LED CHECK
Calibration
LED CHECK
Calibration
0
K-Sensor
EXIT
EXIT
31
PG-A10X-A
TROUBLE SHOOTING TABLE
YES
YES
NO
Checking the basic
performance
Is the POWER LED on or
flickering in red or green?
flickering in red or green?
Go to "Checking the
power unit"
power unit"
Go to "Checking the lamp
light-up"
light-up"
NO
Is the set turned on by the
set’s or remote controller’s
power key?
set’s or remote controller’s
power key?
Go to "Checking the
microcomputer
peripherals".
microcomputer
peripherals".
NO
Go to "Checking the RGB
sync".
sync".
Go to "Checking the RGB
signal"
signal"
Go to "Checking the
video system".
video system".
End
NO
Is the cooling fan
running? Is the lamp on?
running? Is the lamp on?
Is the user menu
displayed?
displayed?
YES
YES
32
PG-A10X-A
YES
YES
YES
YES
NO
Checking the power unit
Are the connectors CN701,
CN702 and CN751
inserted completely?
CN702 and CN751
inserted completely?
Insert the connectors
CN701, CN702 and
CN751 tightly?
CN701, CN702 and
CN751 tightly?
Replace the bimetal
NO
Replace F701.
NO
Check Q702 for damage.
Replace as required.
Replace as required.
NO
Is the bimetal switch off?
Is there AC voltage (110-
240V) applied across
C701?
240V) applied across
C701?
Disconnect the CN751
connector. Is there 6V
output at pins (3) and (4)?
connector. Is there 6V
output at pins (3) and (4)?
Check the MAIN PWB for
short-circuit.
short-circuit.
Click on the first or last page to see other PG-A10XA (serv.man2) service manuals if exist.