DOWNLOAD Sharp PG-A10X (serv.man30) Service Manual ↓ Size: 1.03 MB | Pages: 11 in PDF or view online for FREE

Model
PG-A10X (serv.man30)
Pages
11
Size
1.03 MB
Type
PDF
Document
User Manual / Operation Manual
Brand
Device
Projector / Connections and setup
File
pg-a10x-sm30.pdf
Date

Sharp PG-A10X (serv.man30) User Manual / Operation Manual ▷ View online

Connections and Setup
-19
Optional
cable
3RCA to 15-pin D-sub cable
Type: AN-C3CP
(9'10" (3.0 m))
To analog component output terminal
To audio output terminal
DVD player or
DTV
*
 decoder
Connecting to
Component Video Equip-
ment
Use a 3 RCA to 15-pin D-sub cable when con-
necting to the INPUT 1 terminal, component
video equipment such as DVD players and DTV
*
decoders.
*
DTV is the umbrella term used to describe the
new digital television system in the United
States.
1
Connect the projector to the
video equipment using the 3
RCA to 15-pin D-sub cable.
2
Connect the projector to the
video equipment using a ø3.5
mm minijack to RCA audio cable
(commercially available).
Note
• When connecting the projector to the
video equipment in this way, select
“Component” for “Signal Type” in the
“Picture” menu. See page 
37
.
• A  ø3.5 mm minijack to RCA audio cable
(commercially available) is required for au-
dio input.
1
3 RCA to 15-pin D-sub cable
(sold separately)
2
ø3.5 mm minijack to RCA audio cable
(commercially available)
-20
Connecting to a
Computer Using a DIN-D-
sub RS-232C Adaptor
and an RS-232C Serial
Control Cable
When the RS-232C terminal on the projector is
connected to a computer with a DIN-D-sub RS-
232C adaptor and an RS-232C serial control
cable (cross type, sold separately), the com-
puter can be used to control the projector and
check the status of the projector. See page 
61
for details.
1
Connect the supplied DIN-D-sub
RS-232C adaptor to an RS-232C
serial control cable (sold sepa-
rately).
2
Use the above cables to connect
the projector and the computer.
Note
• Do not connect or disconnect an RS-232C
serial control cable to or from the computer
while it is on. This may damage your com-
puter.
• The RS-232C function may not operate if
your computer terminal is not correctly set
up. Refer to the operation manual of the
computer for details.
• See page 
60
 for connection of an RS-232C
serial control cable.
Optional
cable
RS-232C serial control cable
Type: AN-C10RS (32'10" (10.0 m))
To RS-232C terminal
DIN-D-sub
RS-232C adaptor
Supplied
accessory
Computer
RS-232C serial
control cable
(sold separately)
DIN-D-sub
RS-232C
adaptor
Controlling the Projector Using a Computer
-20
Connecting the Projector to Other Devices
Connections and Setup
-21
Setup
Using the Adjustment
Feet
The height of the projector can be adjusted us-
ing the adjustment feet at the front and rear of
the projector when the surface the projector is
placed on is uneven or when the screen is
slanted.
The projection of the image can be made higher
by adjusting the projector when it is in a lower
place than the screen.
1
While pressing the foot releases
on both sides, lift the projector
to adjust its height and then re-
move your fingers from the foot
releases.
2
Rotate the adjustment feet at the
front of the projector for fine
adjustment.
• You can adjust the projection by using
the rear adjustment foot on the bottom
of the projector when the projector is po-
sitioned at the higher place than the
screen.
Note
• When returning the projector to its original
position, hold the projector firmly, press the
foot releases and then gently lower it.
• The projector is adjustable up to approxi-
mately 12 degrees at the front and 3 de-
grees at the back from the standard posi-
tion.
Info
• Do not press the foot releases when the ad-
justment feet are extended without firmly
holding the projector.
• Do not hold the lens when lifting or lower-
ing the projector.
• When lowering the projector, be careful not
to get your fingers caught in the area be-
tween the adjustment foot and the projec-
tor.
Rear adjustment foot 
(on the bottom)
Front adjustment feet
Foot release
(on the other side of 
the projector as well)
-22
Adjusting the Lens
The image is focused and adjusted to the de-
sired size using the focus ring or zoom knob
on the projector.
1
Adjust the focus by rotating the
focus ring.
2
Adjust zooming by moving the
zoom knob.
-22
Setup
Zoom
 in
Zoo
m o
ut
Zoom knob
Focus ring
Focus ring
Zoom knob
Page of 11
Display

Click on the first or last page to see other PG-A10X (serv.man30) service manuals if exist.