Sharp PG-A10S (serv.man23) User Manual / Operation Manual ▷ View online
Printed in Japan
TINS-B386WJZZ
04P06-JWM
TINS-B386WJZZ
04P06-JWM
Power OFF button
INSTALLATION MANUAL
CAUTION:
••••• Potential hazard of glass particles if lamp ruptures. Please have a Sharp Authorized Projector Dealer or
Service Center* replace lamp if rupture occurs.
••••• Do not remove the lamp unit directly after operation of the projector. The lamp may be extremely hot. Wait at
least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool before
removing the lamp unit.
removing the lamp unit.
■ It is recommended that the lamp be replaced when the remaining lamp life becomes 5% or less, or when you notice a signifi-
cant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display.
■ For lamp replacement, please consult your nearest Sharp Authorized Projector Dealer or Service Center*.
IMPORTANT NOTE TO U.S. CUSTOMERS:
The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this
projector under warranty, including lamp replacement, must be obtained through a Sharp Authorized Projector
Dealer or Service Center*. For the name of the nearest Sharp Authorized Projector Dealer or Service Center*,
please call toll-free: 1-888-GO-SHARP (1-888-467-4277).
The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this
projector under warranty, including lamp replacement, must be obtained through a Sharp Authorized Projector
Dealer or Service Center*. For the name of the nearest Sharp Authorized Projector Dealer or Service Center*,
please call toll-free: 1-888-GO-SHARP (1-888-467-4277).
Hg LAMP CONTAINS MERCURY For State Lamp Disposal Information
www.lamprecycle.org or 1-800-BE-SHARP
www.lamprecycle.org or 1-800-BE-SHARP
U.S.A. ONLY
* Confirm the name of the Dealer or Service Center referring to your projector operation manual.
4
Remove the lamp unit.
• Loosen the securing screws from the lamp unit.
Hold the lamp unit by the handle and pull it in
the direction of the arrow. At this time, keep the
lamp unit horizontal and do not tilt it.
the direction of the arrow. At this time, keep the
lamp unit horizontal and do not tilt it.
5
Insert the new lamp unit.
• Press the lamp unit firmly into the lamp unit
compartment. Fasten the securing screws.
6
Replace the filter/lamp unit cover.
• Align the tab on the filter/lamp unit cover (1)
and place it while pressing the tab (2) to close
it. Then tighten the user service screw (3) to
secure the filter/lamp unit cover.
it. Then tighten the user service screw (3) to
secure the filter/lamp unit cover.
Info
• If the lamp unit and filter/lamp unit cover are not
correctly installed, the power will not turn on, even
if the power cord is connected to the projector.
if the power cord is connected to the projector.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
1
Connect the power cord.
• Plug the power cord into the AC socket of the
projector.
2
Reset the lamp timer.
• While simultaneously holding down
and
on the projector, press
and
on the projector.
• “LAMP 0000H” is displayed, indicating that the
lamp timer is reset.
Info
• Make sure to reset the lamp timer only when re-
placing the lamp. If you reset the lamp timer and
continue to use the same lamp, this may cause the
lamp to become damaged or explode.
continue to use the same lamp, this may cause the
lamp to become damaged or explode.
AC socket
1
2
3
User
service
screw
service
screw
Tab
Securing screws
Handle
1
3
2
User service screw
AC socket
Power ON button
Volume
button
button
AUTO SYNC
button
button
Removing and Installing the
Lamp Unit
Lamp Unit
Info
• Be sure to remove the lamp unit using the handle.
Be sure not to touch the glass surface of the lamp
unit or the inside of the projector.
unit or the inside of the projector.
• To avoid injury to yourself and damage to the lamp,
be sure to carefully follow the steps below.
• Do not loosen other screws except for the filter/lamp
unit cover and lamp unit.
1
Press
on the projector to turn
off the power.
• Wait until the cooling fan stops.
Warning!
• Do not remove the lamp unit from the projector
right after use. The lamp will be very hot and
may cause burn or injury.
may cause burn or injury.
2
Disconnect the power cord.
• Unplug the power cord from the AC socket.
• Leave the lamp until it has fully cooled down
(about 1 hour).
3
Remove the filter/lamp unit cover.
• Turn the projector over. Loosen the user ser-
vice screw (1) that secures the filter/lamp unit
cover. Pressing the tab (2), remove the filter/
lamp unit cover (3).
cover. Pressing the tab (2), remove the filter/
lamp unit cover (3).
• Change the air filter whenever you install the
lamp unit (Please refer to the operation manual.).
LAMP UNIT (LAMP/CAGE MODULE) FOR PROJECTOR
Model
AN-A10LP
(BQC-PGA10X//1)
AN-A10LP_Lamp_E_B&W.p65
04.5.17, 5:32 PM
1
Für Anweisungen in Ihrer Sprache siehe Benutzerhandbuch im PDF-For-
mat auf der mit dem Projektor mitgelieferten CD-ROM.
Sie können das PDF-Benutzerhandbuch auch aus dem Internet
herunterladen (http://sharp-world.com/products/index.html).
mat auf der mit dem Projektor mitgelieferten CD-ROM.
Sie können das PDF-Benutzerhandbuch auch aus dem Internet
herunterladen (http://sharp-world.com/products/index.html).
DEUTSCH
Pour des instructions dans votre langue, reportez-vous au mode d’emploi
PDF contenu dans le CD-ROM fourni avec le projecteur.
Vous pouvez également télécharger le mode d’emploi PDF d’Internet
(http://sharp-world.com/products/index.html).
PDF contenu dans le CD-ROM fourni avec le projecteur.
Vous pouvez également télécharger le mode d’emploi PDF d’Internet
(http://sharp-world.com/products/index.html).
FRANÇAIS
Para recibir instrucciones en su idioma, consulte el manual de manejo
PDF que se encuentra en el CD-ROM suministrado con el proyector.
También puede descargar el manual de manejo PDF de Internet
(http://sharp-world.com/products/index.html).
PDF que se encuentra en el CD-ROM suministrado con el proyector.
También puede descargar el manual de manejo PDF de Internet
(http://sharp-world.com/products/index.html).
ESPAÑOL
Per ricevere istruzioni nella propria lingua, fare riferimento al manuale
d’uso in formato PDF incluso nel CD-ROM fornito con il proiettore.
È possibile, inoltre, scaricare lo stesso manuale d’uso da Internet dal sito
http://sharp-world.com/products/index.html .
d’uso in formato PDF incluso nel CD-ROM fornito con il proiettore.
È possibile, inoltre, scaricare lo stesso manuale d’uso da Internet dal sito
http://sharp-world.com/products/index.html .
ITALIANO
Voor aanwijzingen in uw taal verwijzen wij u naar de PDF-
gebruiksaanwijzing op de CD-ROM die bij de projector wordt geleverd.
U kunt de PDF-gebruiksaanwijzing ook vanaf internet downloaden
(http://sharp-world.com/products/index.html).
gebruiksaanwijzing op de CD-ROM die bij de projector wordt geleverd.
U kunt de PDF-gebruiksaanwijzing ook vanaf internet downloaden
(http://sharp-world.com/products/index.html).
NEDERLANDS
Vi hänvisar till de PDF-filer som återfinns på den medföljande CD-ROM-
skivan för en bruksanvisning på önskat språk.
En bruksanvisning av formatet PDF kan också nerladdas från Internet
(http://sharp-world.com/products/index.html).
skivan för en bruksanvisning på önskat språk.
En bruksanvisning av formatet PDF kan också nerladdas från Internet
(http://sharp-world.com/products/index.html).
SVENSKA
Para instruções no seu idioma, consulte o manual de operação em PDF
contido no CD-ROM fornecido com o projetor.
Pode-se também baixar o manual de operação em PDF pela internet
(http://sharp-world.com/products/index.html).
contido no CD-ROM fornecido com o projetor.
Pode-se também baixar o manual de operação em PDF pela internet
(http://sharp-world.com/products/index.html).
PORTUGUÊS
LampManualXR1S
04.4.23, 2:29 PM
4-5
Display