DOWNLOAD Sharp MX-SP10 Service Manual ↓ Size: 2.76 MB | Pages: 27 in PDF or view online for FREE

MX-RP13/SP10/CS10  UNPACKING AND INSTALLATION  2 - 2

4)

Remove the rear cabinet cover.

Remove the screw and then remove the rear cabinet cover.

5)

Cut out a part of the rear cabinet cover.

Cut out the cut-out portion of the rear cabinet cover with diago-
nal cutters or the like. (Be careful about the orientation of the
diagonal cutters so that the cross section is flat.)

6)

Place the SPF on the copier.

Gently place the SPF on the document glass as shown in the
illustration. At this time, be careful not to damage the original
scanning section and the OC mat.

7)

Connect the SPF with the copier using the relay harness.

<1> Connect the connector.

<2> Fit the harness to the copier using the supplied screw

(M3 

× 8).

<3> Fit the grounding terminal to the copier using the supplied

screw (M3 

× 6).

8)

Attach the rear cabinet.

Fit the four pawls located at the lower part of the rear cabinet
into the copier and secure the cabinet with the three screws.

OC mat

Original scanning

section

Side view

Pawl

★ Pawl

MX-RP13/SP10/CS10  UNPACKING AND INSTALLATION  2 - 3

：'11/Mar/14

9)

Attach the rear cabinet cover.

Fit the harness of the SPF into the cut-out portion of the rear
cabinet cover and secure the cover with the screw.

At this time, check that the three pawls of the rear cabinet
cover are fitted into the rear cabinet.

10) Attach the SPF to the copier.

Attach the SPF by inserting the hinge guide sections of the
SPF into the hinge guides L and R.

11) Insert the power plug into the outlet and turn the main switch of

the copier to the “ON” position.

12) Perform SIM setting.

[MX-SP10]

Execute simulation [2] of [26] and enter [1].

[MX-RP13]

Execute simulation [2] of [26] and enter [2].

13) Carry out automatic adjustment of SPF scanning position.

Use a white sheet and execute simulation [53]-[08] to carry out
automatic adjustment of SPF scanning position.

For details, see the service manual.

14) Adjust the floating detection level of SPF.

Close the SPF and use simulation code [41]-[06] to adjust the
floating detection level of SPF.

For details, see the service manual.

15) Check the copy ratio, and then check the center deviation and

leading edge image void.

Place an original on the document glass and make a copy. 

Then, place an original in the document feeder original tray and
make a copy.

If the center of the copy output from the document glass or the
document feeder is displaced, perform the centering adjust-
ment referring to the service manual of the MX-B200/B201D.

1)

Remove the DV cartridge and the drum cartridge from the
copier.

Open the tray, the side door, and the front cabinet, and then
remove the DV cartridge and the drum cartridge.

Note: Be sure to carry out the operation in the order of (1), (2),

(3), (4), (5), and (6) as illustrated below.

"ON"

•

Screws (M4

× 16): 4 pcs.

MX-RP13/SP10/CS10  UNPACKING AND INSTALLATION  2 - 4

2)

Place the copier on it's right side.

Close the front cover, side cover, and bypass tray, and then
place the copier on it's right side cover as shown in the illustra-
tion.

3)

Remove the OP gear cover and rubber feet from the bottom of
the copier.

Remove the screw and remove the OP gear cover.

Then, take off and remove the rubber feet.

4)

Install the second cassette unit to the copier.

If the second cassette unit is aligned to the copier, it can be
positioned automatically.

Secure the copier to prevent it from falling over and secure the
second cassette unit with four screws (M4 x 16).

5)

Remove the rear cover and connect the connector.

Remove the screw and remove the rear cover of the additional
cassette.

Then, connect the connector of the second cassette unit to that
of the copier.

6)

Attach the rear cover.

Attach the rear cover to its original position and secure it with
the screw (M4 x 12).

7)

Return the copier to the normal orientation.

Carefully lower the machine when returning the copier to it's
original orientation.

Rubber foot

OP gear cover

Rubber foot

MX-RP13/SP10/CS10  UNPACKING AND INSTALLATION  2 - 5

：'11/Mar/14

8)

Insert the drum cartridge and the DV cartridge into the copier.

Open the tray, the side door, and the front cabinet, insert the
drum cartridge and the DV cartridge, and then close the front
cabinet, the side door, and the tray.

Note: When closing, be sure to carry out the operation in the

order of (1), (2), (3), (4), and (5) as illustrated below.

9)

Remove the paper tray lock for packing.

Remove the tray lock by rotating the lock counter-clockwise
and store the lock in the specified position as illustrated below.

10) Set the paper tray length guide.

Squeeze the lever of the paper tray length guide to slide the
guide to the position for the paper size to be used.

11) Load paper into the paper tray.

When loading paper, do not exceed the maximum height line.

12) Insert the power plug into the outlet and turn the main switch to

the “ON” position. Then, perform the following procedure.

13) Perform SIM setting.

Execute simulation [3] of [26] and enter [1].

14) Check the center displacement.

Place an original on the document glass and make a copy
using the tray in the copier.

Then, make a copy using the tray in the installed optional
paper feed unit.

If the center of the copy output from the document glass or the
document feeder is displaced from tray 2, perform the center-
ing adjustment referring to the service manual of the MX-B200/
B201D.