Sharp MX-RB15 Service Manual / Specification ▷ View online
MX-RB15 MAINTENANCE 5 - 1
[5] MAINTENANCE
No.
Maintenance part
When
calling
Every
300K
Remarks
1
Transport roller 1
2
Upper decurler roller
Replace at 1,000K or when wrinkles are made on paper.
3
Upper decurler shaft roller
4
Lower decurler roller
Replace at 1,000K or when wrinkles are made on paper.
5
Lower decurler shaft roller
6
Transport roller 2
7
Belts
---
8
Sensors
---
Transport paper guides
: Check (Clean, replace, or adjust according to necessity.)
: Clean : Replace : Adjust : Lubricate
7
8
1
7
4
2
3
6
5
MX-RB15 DISASSEMBLY AND ASSEMBLY 6 - 1
[6] DISASSEMBLY AND ASSEMBLY
1. Each unit disassembly
A. Upper decurler unit
1)
Open the front door.
Remove the resin E-ring, and slide down the pin.
Remove the front door.
Remove the resin E-ring, and slide down the pin.
Remove the front door.
2)
Remove the screw, and remove the front cabinet.
3)
Remove the screw, and remove the magnet.
4)
Remove the screw, and remove the rear cabinet.
NOTE: When installing the rear cabinet, pass the harness
NOTE: When installing the rear cabinet, pass the harness
through the hole in the rear cabinet.
5)
Disconnect the connecter. Remove the harness from the
clamp, and remove the snap band.
clamp, and remove the snap band.
No.
Unit name
1
Upper decurler unit
2
Decurler unit control PWB
2
1
3
1
2
1
2
1
1
1
2
1
1
1
1
1
2
1
2
3
MX-RB15 DISASSEMBLY AND ASSEMBLY 6 - 2
6)
Disengage the spring from the screw to release the spring
pressure.
NOTE: The spring pressure is very high. Be careful of the
pressure.
NOTE: The spring pressure is very high. Be careful of the
pressure when removing and attaching the spring.
7)
Remove the resin C-ring, and remove the gear, the parallel
pin, and the belt.
NOTE: When the gear is removed, the parallel pin may drop
pin, and the belt.
NOTE: When the gear is removed, the parallel pin may drop
easily. Be careful not to lose it.
8)
Remove the screw, the positioning pin, and the spring.
Remove the upper decurler unit.
Remove the upper decurler unit.
B. Decurler unit control PWB
1)
Remove the screw, and remove the rear cabinet.
NOTE: When installing the rear cabinet, pass the harness
NOTE: When installing the rear cabinet, pass the harness
through the hole in the rear cabinet.
2)
Remove the screw, and remove the plate.
3)
Disconnect the connector from the decurler unit control PWB.
Remove the screw and the supporter, and remove the decurler
unit control PWB.
Remove the screw and the supporter, and remove the decurler
unit control PWB.
1
2
3
4
4
1
2
1
3
2
1
1
1
1
2
1
1
2
2
1
1
3
1
3
2
1
1
1
1
1
MX-RB15 DISASSEMBLY AND ASSEMBLY 6 - 3
2. Maintenance
A. Upper decurler roller, Upper decurler shaft
roller, Lower decurler roller, Lower decurler
shaft roller, Transport roller 1, Transport roller
2
shaft roller, Transport roller 1, Transport roller
2
1)
Open the front door, and open the upper decurler unit. Clean
the rollers.
the rollers.
B. Upper decurler roller
1)
Open the front door.
Remove the resin E-ring, and slide down the pin.
Remove the front door.
Remove the resin E-ring, and slide down the pin.
Remove the front door.
2)
Remove the screw, and remove the front cabinet.
3)
Remove the screw, and remove the front cabinet lower.
4)
Remove the E-ring, and remove the bearing.
Slide the upper decurler roller to rear frame side, and remove
the bearing from the frame.
Remove the upper decurler roller.
Slide the upper decurler roller to rear frame side, and remove
the bearing from the frame.
Remove the upper decurler roller.
NOTE: Keep the mylar sheet position on the right side of the
roller when attach the upper decurler roller.
NOTE: Set the pressure adjustment lever to the position “1”
when attach the upper decurler roller.
C. Lower decurler roller
1)
Open the front door.
Remove the resin E-ring, and slide down the pin.
Remove the front door.
Remove the resin E-ring, and slide down the pin.
Remove the front door.
3
1
2
1
2
1
1
1
2
1
4
1
2
3
3
1
2
Click on the first or last page to see other MX-RB15 service manuals if exist.