Sharp MX-RB15 (serv.man3) Service Manual ▷ View online
MX-7040N MX-RB15 (CURL CORRECTION UNIT) 16 – 1
MX-7040N
Service Manual
[16] MX-RB15 (CURL CORRECTION UNIT)
1. Unpacking
A. Decurler unit removal
NOTE: When moving the unit, use manpower of two or more per-
sons.
B. Fixing tape and protection material removal
1)
Remove fixing tape and fixing bracket from the decurler unit.
C. Packed items check
D. Cushion attachment
No.
Name
Qua
ntity
Rear
MX-
CF11
+
MX-
FD10
MX-
CF11
+
MX-
RB13
MX-
FD10
MX-
FN21
MX-
FN22
1
Screw
(M3 x 6 RS tight)
(M3 x 6 RS tight)
10
10
10
4
4
6
2
Screw
(M4 x 8 RS tight)
(M4 x 8 RS tight)
2
---
---
2
2
2
3
Screw
(M4 x 7 Round tup)
(M4 x 7 Round tup)
2
2
2
2
2
2
4
Screw
(M4 x 12 Bind)
(M4 x 12 Bind)
4
4
4
4
4
4
5
M4 step screw
2
2
2
2
2
2
6
Connection plate F
1
1
1
1
1
1
7
Connection plate R
1
1
1
1
1
1
8
Earth bracket
1
1
---
1
1
1
9
Shunt cable
connection plate
connection plate
1
---
---
1
1
1
10
Rear upper cover
1
1
1
1
1
1
11
Paper guide A
1
---
1
1
1
1
12
Paper guide B
1
1
---
---
---
---
13
Paper guide C
1
1
1
---
---
---
14
Protection sheet
1
1
1
---
---
1
15
Top surface
cushion
cushion
1
1
1
1
1
1
1
2
3
4
5
6
7
8
9
10
14
15
13
11
12
Cushion attachment
position
position
Reference of cushion on.
(Rear screw hole tiered edge)
(Rear screw hole tiered edge)
Reference of cushion on.
(Upper cabinet lower edge)
(Upper cabinet lower edge)
MX-7040N MX-RB15 (CURL CORRECTION UNIT) 16 – 2
2. Installation
NOTE: Installation must be executed in the sequence of the com-
plex machine body, the paper feed option, and the paper
exit option.
exit option.
NOTE: Before installation, be sure to turn both the operation and
main power switches off and disconnect the power plug
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.
from the power outlet. Make double sure that the data lamp
on the operation panel does not light up or blink when per-
forming installation.
NOTE: To prevent against falling during installation, extend the
stand rail.
A. Connection plates F/R attachment
1)
Attach the connection plates F/R (Packed items No.6, 7) and
fix them with the screws (Packed items No.4).
fix them with the screws (Packed items No.4).
B. Shunt cable connection plate installation
(Back of the decurler unit)
1)
Fix the shunt cable connection plate (Packed items No.9) with
the screws (Packed items No.2).
the screws (Packed items No.2).
C. Rear upper cover installation
1)
Attach the rear upper cover (Packed items No.10) and fix it
with the screw (Packed items No.3).
with the screw (Packed items No.3).
D. Earth bracket installation
1)
Fix the earth bracket (Packed items No.8) with the screws
(Packed items No.1).
(Packed items No.1).
NOTE: Use the outside screw holes for fixing.
E. Install to main unit
1)
Return the stand rail to the original position.
2)
Connect the unit to the machine.
Insert the pin in the machine side into the hole in the R side of
the unit.
Insert the pin in the machine side into the hole in the R side of
the unit.
MX-7040N MX-RB15 (CURL CORRECTION UNIT) 16 – 3
F. Height and tilt adjustment
NOTE: When the adjuster bolt is turned counterclockwise, the
height is decreased. When turned clockwise, the height is
increased.
increased.
NOTE: For the height and tilt adjustment, use the three adjuster
bolts under the unit.
Turn the adjustment nuts of the casters with a wrench in the arrow
direction to adjust the height. (When turning the adjustment nut one
rotation, the height of the curl correction unit is changed by about
1.75mm.)
• To increase the curl correction unit height, turn the nut in the
direction to adjust the height. (When turning the adjustment nut one
rotation, the height of the curl correction unit is changed by about
1.75mm.)
• To increase the curl correction unit height, turn the nut in the
direction [A].
• To decrease the curl correction unit height, turn the nut in the
direction [B].
NOTE: Use the wrench attached to the finisher.
1)
Use adjuster bolt (1) to adjust the height so that the center of
the hole for the unit fixing screw in the F side is aligned with
the center marking-off line.
the hole for the unit fixing screw in the F side is aligned with
the center marking-off line.
2)
Use adjuster bolt (2) to adjust the height so that the center of
the hole for the unit fixing screw in the R side is aligned with
the center marking-off line.
the hole for the unit fixing screw in the R side is aligned with
the center marking-off line.
3)
Use adjuster bolt (3) so that the clearance between the
machine and the unit becomes uniform.
machine and the unit becomes uniform.
G. Fixing to the machine
1)
Fix the unit to the machine with the step screws (Packed
items).
items).
H. Connection of connector to the main unit
1)
Connect the three connectors of the unit to the machine, and
fix with the screws.
fix with the screws.
Ԙ
Ԛ
ԙ
Display