Sharp MX-RB12 (serv.man3) Service Manual ▷ View online
MX-RB12 MAINTENANCE 5 – 2
2. Each unit removal
A. Interface unit
1) Pull out the interface unit, and remove four screws.
Note: When the upper guide unit is removed, an adjustment is
required to install it again.
required to install it again.
2) Remove the rear cabinet and interface transport fan motor 2.
3)
Remove the bracket and the band.
When installing, fit the bracket with the adjustment reference.
No.
Name
1
Interface unit
1
1
4
3
3
1
2
1
5
4
4
3
3
1
2
Adjustment
reference
d0.5
reference
d0.5
MX-RB12 MAINTENANCE 5 – 3
3. Disassembly and assembly in each unit
A. Rollers
1) Remove the interface unit.
2) Open the upper guide unit, and clean the rollers.
2) Open the upper guide unit, and clean the rollers.
B. Sensors
1)
Remove the interface unit.
2)
Remove the left paper exit cabinet, and check the paper inter-
face cover open/close sensor.
face cover open/close sensor.
3)
Remove the cover bottom at the back surface, and check the
interface transport unit inlet port sensor.
interface transport unit inlet port sensor.
No.
Name
1
Paper exit roller (Idle)
2
Paper exit front roller (Idle)
3
Interface roller (Idle)
4
Inlet port rear roller (Idle)
5
Inlet port roller (Idle)
6
Paper exit roller (Drive)
7
Paper exit front roller (Drive)
8
Interface roller (Drive)
9
Inlet port rear roller (Drive)
10
Inlet port roller (Drive)
2
3
4
1
6
7
8
9
10
5
No.
Name
1
Paper interface transport unit insertion sensor
2
Interface transport unit inlet port sensor
3
Interface transport unit outlet port sensor
2
3
1
2
1
1
1
1
1
1
2
MX-RB12 MAINTENANCE 5 – 4
4) Remove the Mylar, and check the interface transport unit outlet
port sensor.
C. Motors, fans, and solenoids
1) Remove the interface unit.
2) Remove the front cabinet, and check the interface reverse
2) Remove the front cabinet, and check the interface reverse
path solenoid.
3) Remove the rear cabinet, and check the transport motor 2.
4)
Remove the cover bottom at the back surface, and check the
interface fan and the interface transport motor 1.
interface fan and the interface transport motor 1.
NOTE: When the interface reverse path solenoid is removed, an
adjustment is required when installing it again.
When installing, fit it with the adjustment reference.
Press the solenoid with your hand, and perform the following
adjustment.
adjustment.
No.
Name
1
Interface fan
2
Interface transport motor 1
3
Interface transport motor 2
4
Interface reverse path solenoid
1
1
2
3
2
1
4
1
1
1
1
1
2
1
2
1
1
1
2
Adjustment
reference
d0.5
17r1mm
MX-RB12 ELECTRICAL SECTION 6 – 1
MX-RB12
Service Manual
[6] ELECTRICAL SECTION
1. Block diagram
㪤㪸㫀㫅㩷㪚㫆㫅㫋㫉㫆㫃
㩷
㪙㫆㪸㫉㪻
㪚
㪥
㪊㪇㪈
㪩㪜
㪣㪘
㪰㪶㪂㪉㪋㪭
㪝㪘
㪥㪶㪂㪉㪋㪭
㪞㪥㪛㪉
㪂㪌㪭
㪩㪜㪣㪘㪰㩷㪦㪧㪜㪥㩷㪪㪜㪥㪪㪦㪩㩷㩿㪧㪛㪦㪪㪀
㪪
㪜
㪥㪪㪦㪩㩷㪪㪠㪞㪥㪘㪣
㪪㪜㪥㪪㪦㪩㩷㪪㪠
㪞㪥㪘
㪣
㪪㪜㪥㪪㪦㪩㩷㪪㪠
㪞㪥㪘
㪣
㪂㪌㪭㪈
㪂㪌㪭㪈
㪂㪌㪭㪈
*1'
㪞㪥㪛
㪈
㪂㪌㪭㪈
㪞㪥㪛㪈
㪩㪜㪣㪘㪰㩷㪧㪘㪪㪪㩷㪪㪜㪥㪪㪦㪩㩷㩿㪧㪛㪧㪧㪛㪉㪀
㪩㪜㪣㪘㪰㩷㪜㪥㪫㪩㪘㪥㪚㪜㩷㪪㪜㪥㪪㪦㪩㩷㩿㪧㪛㪧㪧㪛㪈㪀
㪩㪜㪣㪘㪰㩷㪠㪥㪣㪜㪫㩷㪤㪦㪫㪦㪩㩷㩿㪧㪛㪧㪫㪤㪀
㪤㪦
㪫
㪦
㪩
㪶㪘
㪤㪦
㪫
㪦
㪩
㪶㪁
㪘
㪤㪦
㪫
㪦
㪩㪶
㪙
㪤㪦
㪫
㪦
㪩㪶
㪁㪙
㪞㪥㪛
㪈
㪠㪚㪧㪪㪇㪅
㪌
㪇㪅㪌㪘
㪝㪘㪥㩷
㪘㪩㪘
㪩
㪤
㪩㪜㪣㪘㪰㩷㪝㪘㪥㩷㩿㪧㪛㪚㪝㪀
㪪㪦㪣㪜㪥㪦
㪠㪛㩷㪚
㪦
㪥
㪫
㪩
㪦㪣
㪩㪜㪣㪘㪰㩷㪝㪣㪘㪧㩷㪪㪦㪣㪜㪥㪦㪠㪛㩷㩿㪧㪛㪧㪞㪪㪀
㪚
㪥
㪊㪇㪉
㪚
㪥
㪊㪇㪊
㪚㪥
㪊㪇㪋
㪛㪩㪘㪮
㪜
㪩
㩷㪚
㪦
㪥
㪥㪜㪚㪫㪦㪩
㪧㪚㪙㪄㪩㪜㪣㪘㪰㪈
㪩㪜㪣㪘㪰㩷㪜㪯㪠㪫㩷㪤㪦㪫㪦㪩㩷㩿㪧㪙㪤㪈㪇㪉㪀
㪤㪦㪫㪦㪩㪶㪘
㪤㪦
㪫㪦
㪩㪶㪁㪘
㪤㪦㪫㪦㪩㪶
㪙
㪤㪦
㪫㪦㪩㪶
㪁㪙
㪚㪥㪊㪇㪈㪙
Click on the first or last page to see other MX-RB12 (serv.man3) service manuals if exist.