Sharp MX-PNX6 Service Manual ▷ View online
MX-FN11 OPERATIONAL DESCRIPTION 4 – 17
8. Power supply system
A. Power supply route in finisher
The finisher controller PCB is supplied with two power supply sys-
tems, 13 VDC and 24 VDC, when the host machine is turned on.
The 24 VDC power supply system is intended for drive of the
motors and solenoids. As for the 13 VDC power supply system,
after the power is converted to 5 VDC by the regulator IC (IC28) on
the finisher controller PCB, it is used for drive of the sensors. After
it is converted to 3.3 VDC by the regulator IC(IC7) on the finisher
controller PCB, it is used for drive of the IC in the PCB. Power from
the power supply systems is supplied to the saddle stitcher control-
ler PCB from the finisher controller PCB.
The power is also supplied from the finisher controller PCB to the
saddle stitch controller PCB. In addition, it is also supplied to the
punch controller PCB when the optional punch module is mounted.
Some of the 24 VDC power used to drive motors is cut off when the
front/cover close detector switch (FFDD) is open. Figure shown
below is a block diagram showing the power supply system.
tems, 13 VDC and 24 VDC, when the host machine is turned on.
The 24 VDC power supply system is intended for drive of the
motors and solenoids. As for the 13 VDC power supply system,
after the power is converted to 5 VDC by the regulator IC (IC28) on
the finisher controller PCB, it is used for drive of the sensors. After
it is converted to 3.3 VDC by the regulator IC(IC7) on the finisher
controller PCB, it is used for drive of the IC in the PCB. Power from
the power supply systems is supplied to the saddle stitcher control-
ler PCB from the finisher controller PCB.
The power is also supplied from the finisher controller PCB to the
saddle stitch controller PCB. In addition, it is also supplied to the
punch controller PCB when the optional punch module is mounted.
Some of the 24 VDC power used to drive motors is cut off when the
front/cover close detector switch (FFDD) is open. Figure shown
below is a block diagram showing the power supply system.
B. Protect functions of finisher
The 24 VDC power line used to drive motors and solenoids is
equipped with a fuse or motor driver having overcurrent protector.
equipped with a fuse or motor driver having overcurrent protector.
C. Punch module (option)
(1) Outline
When the host machine is turned on, the punch module is supplied
by the finisher control PCB with 24-V and 5-V power.
The 24-V power is used to drive the motors, while the 5-V power is
used by sensors and the ICs on the punch control PCB.
The 24-V power to the motors will be cut off when the joint switch of
the finisher is open. The following is a block diagram for the power
supply system.
by the finisher control PCB with 24-V and 5-V power.
The 24-V power is used to drive the motors, while the 5-V power is
used by sensors and the ICs on the punch control PCB.
The 24-V power to the motors will be cut off when the joint switch of
the finisher is open. The following is a block diagram for the power
supply system.
(2) Protective mechanisms
The 24-V system used to drive the punch motor is equipped with a
built-in fuse that melts in the presence of overcurrent.
built-in fuse that melts in the presence of overcurrent.
Front cover close
detection switch (FFDD)
Saddle stitcher
controller PCB
Finisher controller PCB
Host
machine
Motor
Motor
Solenoids
Sensor
system
Logic
system
Regulator IC
Regulator IC
(IC28)
(IC7)
Punch controller PCB
(Punch module (optional))
Finisher
control
PCB
Upper door
switch
(FPUDSW)
Front door
switch
(FPFDD)
Punch control PCB
Motor system
Motor system
LED PCB
Sensor system
Logic system
MX-FN11 DISASSEMBLY AND ASSEMBLY 5 – 1
MX-FN11
Service Manual
[5] DISASSEMBLY AND
ASSEMBLY
1. Finisher (MX-FN11)
A. Exterior cover
(1) Front cover
a. Removal of front cover
1) Remove a screw [1] to remove the foot cover [2].
1) Remove a screw [1] to remove the foot cover [2].
2) Remove the three screws [3], and slide the front cover [4] to
the left and remove it.
(2) Rear cover
a. Removal of rear cover
1)
1)
Remove the three screws [1], and lift and remove the rear
cover [2].
cover [2].
(3) Left upper cover
a. Removal of front cover
1)
1)
Remove a screw [1] to remove the foot cover [2].
2)
Remove the three screws [3], and slide the front cover [4] to
the left and remove it.
the left and remove it.
[1]
[2]
[4]
[3]
[1]
[2]
[1]
[2]
[4]
[3]
MX-FN11 DISASSEMBLY AND ASSEMBLY 5 – 2
b. Removal of rear cover
1) Remove the three screws [1], and lift and remove the rear
1) Remove the three screws [1], and lift and remove the rear
cover [2].
c. Removal of left upper cover
1) Remove the two screws [1].
2) With the upper door [2] open, tilt the left upper cover [3] to the
1) Remove the two screws [1].
2) With the upper door [2] open, tilt the left upper cover [3] to the
right, and remove it.
CAUTION: When installing, be sure to engage the two pawls [4] of
the left upper cover with the metal plates.
(4) Upper door
a. Removal of front cover
1)
1)
Remove a screw [1] to remove the foot cover [2].
2)
Remove the three screws [3], and slide the front cover [4] to
the left and remove it.
the left and remove it.
[1]
[2]
[3]
[2]
[1]
[4]
[1]
[2]
[4]
[3]
MX-FN11 DISASSEMBLY AND ASSEMBLY 5 – 3
b. Removal of rear cover
1) Remove the three screws [1], and lift and remove the rear
1) Remove the three screws [1], and lift and remove the rear
cover [2].
c. Removal of left upper cover
1) Remove the two screws [1].
2) With the upper door [2] open, tilt the left upper cover [3] to the
1) Remove the two screws [1].
2) With the upper door [2] open, tilt the left upper cover [3] to the
right, and remove it.
CAUTION: When installing, be sure to engage the two pawls [4] of
the left upper cover with the metal plates.
d. Removal of upper door
1)
1)
Open the upper door [1], and disengage the hooks [2] at two
positions.
positions.
2)
Remove the screw [3], and remove the upper door [1].
(5) Grate-shaped upper guide
a. Removal of front cover
1)
1)
Remove a screw [1] to remove the foot cover [2].
[1]
[2]
[3]
[2]
[1]
[4]
[3]
[1]
[2]
[1]
[2]
Click on the first or last page to see other MX-PNX6 service manuals if exist.