DOWNLOAD Sharp MX-PNX1C (serv.man8) Service Manual ↓ Size: 6.55 MB | Pages: 13 in PDF or view online for FREE

Model
MX-PNX1C (serv.man8)
Pages
13
Size
6.55 MB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / Section -6 - Disassembly and Assembly .
File
mx-pnx1c-sm8.pdf
Date

Sharp MX-PNX1C (serv.man8) Service Manual ▷ View online

MX-FNX1/MX-PNX1  DISASSEMBLY AND ASSEMBLY  6 – 10
5)
Remove the gear, and remove the tray motor.
(5) Tray paper empty sensor
1)
Remove the inner finisher from the main unit. Refer to A-(1).
2)
Remove the left cover and the bottom cover. Refer to A-(4).
3)
Remove the tray bottom cover.
4)
Pull out the tray. Remove the screw, and remove the tray.
5)
Remove the tray paper empty sensor.
F. Others
(1) Control PWB
1)
Remove the inner finisher from the main unit. Refer to A-(1).
2)
Remove the rear cover. Refer to A-(3).
3)
Disconnect the connector, and remove the screw. Remove the
PWB support and remove the control PWB.
(2) Fan
1)
Remove the inner finisher from the main unit. Refer to A-(1).
2)
Shift the staple unit to the rear side. Disconnect the connector
and remove the fan.
* When installing, take care that the label of the fan comes to
the direction illustrated.
(3) Front cover switch
1)
Remove the inner finisher from the main unit. Refer to A-(1).
2)
Remove the inner cover. Refer to A-(2).
3)
Remove the spring, and remove the interlock sensor lever.
Remove the front cover switch, and disconnect the connector.
1
2
1
2
3
2
3
2
3
1
2
3
4
Blue
Red
Yellow
MX-FNX1/MX-PNX1  DISASSEMBLY AND ASSEMBLY  6 – 11
2. MX-PNX1A/B/C/D
A. Punch unit (MX-PNX1A/B/C/D)
(1) Punch unit (MX-PNX1A/B/C/D)
1)
Remove the coin screw, and remove the finisher slide stopper.
2)
Open the front cover, and slide the inner finisher.
3)
Remove the dust box.
4)
Remove the punch cover.
5)
Remove the punch unit from the main unit.
(2) LED light receiving PWB
1)
Remove the punch unit. Refer to A-(1).
2)
Remove the PWB holder, and remove the LED light receiving
PWB.
(3) Punch horizontal resist motor
1)
Remove the punch unit. Refer to A-(1).
2)
Remove the guide cover. Disconnect the connector, and
remove the harness guide.
2
1
1
2
2
3
MX-FNX1/MX-PNX1  DISASSEMBLY AND ASSEMBLY  6 – 12
3)
Remove the punch horizontal resist motor.
(4) Punch PWB
1)
Remove the punch unit. Refer to A-(1).
2)
Remove the guide cover and the harness guide. Refer to A-
(3).
3)
Remove the punch PWB.
(5) Punch motor
1)
Remove the punch unit. Refer to A-(1).
2)
Disconnect the connector, and remove the link plate. Remove
the spring, and separate the upper unit and the lower unit.
3)
Fit the gear hole with the screw position, and remove the
screw. Remove the punch motor.
(6) LED light emitting PWB
1)
Remove the punch unit. Refer to A-(1).
2)
Remove the lower unit. Refer to A-(5).
3)
Remove the roller and the PWB holder. Remove the LED light
emitting PWB.
(7) Rear position sensor
1)
Remove the punch unit. Refer to A-(1).
2)
Remove the rear position sensor.
4
4
4
5
2
3
1
1
2
1
3
2
MX-FNX1/MX-PNX1  DISASSEMBLY AND ASSEMBLY  6 – 13
(8) Punch position sensor
1)
Remove the punch unit. Refer to A-(1).
2)
Remove the upper unit. Refer to A-(5).
3)
Remove the harness guide.
4)
Remove the punch position sensor.
(9) Horizontal shift HP sensor
1)
Remove the punch unit. Refer to A-(1).
2)
Remove the guide cover and the harness guide. Refer to A-
(3).
3)
Disconnect the connector, and remove the harness.
4)
Remove the screws and the pawl, and lift up the harness
guide. Disconnect the connector, and remove the horizontal
shift HP sensor.
(10) Full sensor
1)
Remove the punch unit. Refer to A-(1).
2)
Remove the drive bracket, and remove the full sensor.
3
2
1
Page of 13
Display

Click on the first or last page to see other MX-PNX1C (serv.man8) service manuals if exist.