DOWNLOAD Sharp MX-PNX1C (serv.man8) Service Manual ↓ Size: 6.55 MB | Pages: 13 in PDF or view online for FREE

Model
MX-PNX1C (serv.man8)
Pages
13
Size
6.55 MB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / Section -6 - Disassembly and Assembly .
File
mx-pnx1c-sm8.pdf
Date

Sharp MX-PNX1C (serv.man8) Service Manual ▷ View online

MX-FNX1/MX-PNX1  DISASSEMBLY AND ASSEMBLY  6 – 8
(3) Alignment plate position sensor
1)
Remove the inner finisher from the main unit. Refer to A-(1).
2)
Shift the staple unit to the front side.
3)
Remove the bracket and remove the position sensor.
(4) Staple shift motor
1)
Remove the inner finisher from the main unit. Refer to A-(1).
2)
Remove the inner cover. Refer to A-(2).
3)
Remove the rear cover. Refer to A-(3).
4)
Remove the reverse guide unit. Refer to A-(5).
5)
Remove the roller up/down motor. Refer to B-(6).
6)
Remove the E-ring, the flange and the gear pulley, and remove
the gear.
7)
Disconnect the connector from the PWB, and remove the sta-
ple shift motor.
(5) Stapler HP sensor
1)
Remove the inner finisher from the main unit. Refer to A-(1).
2)
Remove the inner cover. Refer to A-(2).
3)
Put the inner finisher upside down, and remove the stapler HP
sensor.
E. Paper exit tray section
(1) Paper surface sensors 1, 2
1)
Remove the inner finisher from the main unit. Refer to A-(1).
2)
Remove the inner cover. Refer to A-(2).
3)
Remove the tray unit. Refer to B-(10).
4)
Remove the load cover. Refer to C-(1).
5)
Remove the parts, and remove the sensor lever.
MX-FNX1/MX-PNX1  DISASSEMBLY AND ASSEMBLY  6 – 9
6)
Remove the bracket, and remove the paper surface sensors 1,
2.
(2) Paper surface detection solenoid
1)
Remove the inner finisher from the main unit. Refer to A-(1).
2)
Remove the inner cover. Refer to A-(2).
3)
Remove the tray unit. Refer to B-(10).
4)
Remove the bundle exit paper transport roller unit, the sensor
lever, the process tray unit. Refer to C-(1).
5)
Remove the paper surface detection solenoid unit, and
remove the paper surface detection solenoid.
(3) Tray upper limit sensor, tray intermediate lower 
limit sensor, tray lower limit sensor
1)
Remove the inner finisher from the main unit. Refer to A-(1).
2)
Remove the tray unit. Refer to B-(10).
3)
Remove the harness guide, and remove the tray upper limit
sensor, the tray intermediate lower limit sensor, and the tray
lower limit sensor.
(4) Tray motor
1)
Remove the inner finisher from the main unit. Refer to A-(1).
2)
Remove the tray unit. Refer to B-(10).
3)
Remove the tray left bracket and the tray drive unit.
4)
Remove the tray drive unit.
MX-FNX1/MX-PNX1  DISASSEMBLY AND ASSEMBLY  6 – 10
5)
Remove the gear, and remove the tray motor.
(5) Tray paper empty sensor
1)
Remove the inner finisher from the main unit. Refer to A-(1).
2)
Remove the left cover and the bottom cover. Refer to A-(4).
3)
Remove the tray bottom cover.
4)
Pull out the tray. Remove the screw, and remove the tray.
5)
Remove the tray paper empty sensor.
F. Others
(1) Control PWB
1)
Remove the inner finisher from the main unit. Refer to A-(1).
2)
Remove the rear cover. Refer to A-(3).
3)
Disconnect the connector, and remove the screw. Remove the
PWB support and remove the control PWB.
(2) Fan
1)
Remove the inner finisher from the main unit. Refer to A-(1).
2)
Shift the staple unit to the rear side. Disconnect the connector
and remove the fan.
* When installing, take care that the label of the fan comes to
the direction illustrated.
(3) Front cover switch
1)
Remove the inner finisher from the main unit. Refer to A-(1).
2)
Remove the inner cover. Refer to A-(2).
3)
Remove the spring, and remove the interlock sensor lever.
Remove the front cover switch, and disconnect the connector.
1
2
1
2
3
2
3
2
3
1
2
3
4
Blue
Red
Yellow
MX-FNX1/MX-PNX1  DISASSEMBLY AND ASSEMBLY  6 – 11
2. MX-PNX1A/B/C/D
A. Punch unit (MX-PNX1A/B/C/D)
(1) Punch unit (MX-PNX1A/B/C/D)
1)
Remove the coin screw, and remove the finisher slide stopper.
2)
Open the front cover, and slide the inner finisher.
3)
Remove the dust box.
4)
Remove the punch cover.
5)
Remove the punch unit from the main unit.
(2) LED light receiving PWB
1)
Remove the punch unit. Refer to A-(1).
2)
Remove the PWB holder, and remove the LED light receiving
PWB.
(3) Punch horizontal resist motor
1)
Remove the punch unit. Refer to A-(1).
2)
Remove the guide cover. Disconnect the connector, and
remove the harness guide.
2
1
1
2
2
3
Page of 13
Display

Click on the first or last page to see other MX-PNX1C (serv.man8) service manuals if exist.