DOWNLOAD Sharp MX-PNX1C (serv.man8) Service Manual ↓ Size: 6.55 MB | Pages: 13 in PDF or view online for FREE

Model
MX-PNX1C (serv.man8)
Pages
13
Size
6.55 MB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / Section -6 - Disassembly and Assembly .
File
mx-pnx1c-sm8.pdf
Date

Sharp MX-PNX1C (serv.man8) Service Manual ▷ View online

MX-FNX1/MX-PNX1  DISASSEMBLY AND ASSEMBLY  6 – 5
8)
Remove the tray unit.
9)
Remove the harness from the guide, and remove the bottom
plate.
10) Remove the inlet port upper guide.
11) Remove the spring, and remove the parts. Remove the inlet
port gate.
(11) Inlet port paper transport roller
1)
Remove the inner finisher from the main unit. Refer to A-(1).
2)
Remove the inner cover. Refer to A-(2).
3)
Remove the tray unit. Refer to B-(10).
4)
Remove the bottom plate. Refer to B-(10).
5)
Remove the inlet port upper guide, and remove the transport
guide.
6)
Remove the parts, and remove the inlet port paper transport
roller.
(12) Transport motor
1)
Remove the inner finisher from the main unit. Refer to A-(1).
2)
Remove the inner cover. Refer to A-(2).
3)
Remove the tray unit. Refer to B-(10).
4)
Remove the bottom plate. Refer to B-(10).
5)
Disconnect the connector, and remove the transport motor.
1
2
3
1
1
2
3
4
2
1
2
3
MX-FNX1/MX-PNX1  DISASSEMBLY AND ASSEMBLY  6 – 6
(13) Bundle exit motor
1)
Remove the inner finisher from the main unit. Refer to A-(1).
2)
Remove the inner cover. Refer to A-(2).
3)
Remove the tray unit. Refer to B-(10).
4)
Remove the bottom plate. Refer to B-(10).
5)
Disconnect the connector, and remove the bundle exit motor.
(14) Paddle one-rotation solenoid
1)
Remove the inner finisher from the main unit. Refer to A-(1).
2)
Remove the inner cover. Refer to A-(2).
3)
Remove the tray unit. Refer to B-(10).
4)
Remove the bottom plate. Refer to B-(10).
5)
Remove the paddle one-rotation solenoid.
C. Process tray section
(1) Alignment motors F and R
1)
Remove the inner finisher from the main unit. Refer to A-(1).
2)
Remove the inner cover. Refer to A-(2).
3)
Remove the tray unit. Refer to B-(10).
4)
Remove the load cover. Refer to B-(10).
5)
Remove the bundle exit paper transport unit.
6)
Remove each parts, and remove the sensor lever.
7)
Remove the center weight, and remove the process tray unit.
1
2
3
1
1
1
2
1
2
MX-FNX1/MX-PNX1  DISASSEMBLY AND ASSEMBLY  6 – 7
8)
Remove the alignment plate. Remove the screws and the
pawl, and remove the process tray.
9)
Slide the unit and remove the alignment motors F and R.
(2) Empty sensor, alignment plate HP sensors F and R
1)
Remove the inner finisher from the main unit. Refer to A-(1).
2)
Remove the inner cover. Refer to A-(2).
3)
Remove the tray unit. Refer to B-(10).
4)
Remove the process tray unit. Refer to C-(1).
5)
Remove the bracket and the empty sensor. Remove the align-
ment plate HP sensors F and R.
D. Staple section
(1) Staple cartridge
1)
Open the front cover, and slide the inner finisher. Refer to B-
(1).
2)
Release the lock, and remove the staple cartridge.
(2) Staple unit
1)
Remove the inner finisher from the main unit. Refer to A-(1).
2)
Remove the inner cover. Refer to A-(2).
3)
Remove the latch cover. Remove the parts and the shaft.
4)
Remove the screw from the bottom. Remove the staple unit,
and disconnect the connector.
1
2
1
2
4
3
5
1
2
MX-FNX1/MX-PNX1  DISASSEMBLY AND ASSEMBLY  6 – 8
(3) Alignment plate position sensor
1)
Remove the inner finisher from the main unit. Refer to A-(1).
2)
Shift the staple unit to the front side.
3)
Remove the bracket and remove the position sensor.
(4) Staple shift motor
1)
Remove the inner finisher from the main unit. Refer to A-(1).
2)
Remove the inner cover. Refer to A-(2).
3)
Remove the rear cover. Refer to A-(3).
4)
Remove the reverse guide unit. Refer to A-(5).
5)
Remove the roller up/down motor. Refer to B-(6).
6)
Remove the E-ring, the flange and the gear pulley, and remove
the gear.
7)
Disconnect the connector from the PWB, and remove the sta-
ple shift motor.
(5) Stapler HP sensor
1)
Remove the inner finisher from the main unit. Refer to A-(1).
2)
Remove the inner cover. Refer to A-(2).
3)
Put the inner finisher upside down, and remove the stapler HP
sensor.
E. Paper exit tray section
(1) Paper surface sensors 1, 2
1)
Remove the inner finisher from the main unit. Refer to A-(1).
2)
Remove the inner cover. Refer to A-(2).
3)
Remove the tray unit. Refer to B-(10).
4)
Remove the load cover. Refer to C-(1).
5)
Remove the parts, and remove the sensor lever.
Page of 13
Display

Click on the first or last page to see other MX-PNX1C (serv.man8) service manuals if exist.