DOWNLOAD Sharp MX-PNX1C (serv.man10) Service Manual ↓ Size: 216.16 KB | Pages: 2 in PDF or view online for FREE

Model
MX-PNX1C (serv.man10)
Pages
2 Few pages! See other manuals at the bottom of the first or last page.
Size
216.16 KB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / Section -8 - Adjustments .
File
mx-pnx1c-sm10.pdf
Date

Sharp MX-PNX1C (serv.man10) Service Manual ▷ View online

MX-FNX1/MX-PNX1  ADJUSTMENTS  8 – 1
âºíuÇ´
Service Manual
 
[8] ADJUSTMENTS
Each adjustment item in the adjustment item list is identified with its
own JOB No. The adjustments are basically executed in the
sequence from a smaller JOB No. to a larger JOB No.
There is, however, no need to perform all the adjustment items.
Only the necessary items may be executed depending on the situa-
tion.
Unnecessary items may be skipped to go to the next necessary
item. In this case, of course, the adjustment sequence could be
executed from a smaller to a larger JOB No.
If the above is neglected, the adjustment cannot be completed nor-
mally, resulting in a trouble.
[Start of simulation]
1)
Press [COPY MODE] key to enter the copy mode.
2)
Press [P] (Program) key 
→ [*] (Asterisk) key → [C] (Clear) key
→ [*] (Asterisk) key in this sequence.
3)
The display is shifted to the simulation main number entry
screen (entry standby screen).
1. Setting item list
2. Details
 
1
Punch unit, punch PWB destination
setting
1)
When the punch PWB is replaced, the destination setting must
be performed.
2)
For destination setting, the DIP switch (SW1) on the punch
PWB is used.
3)
The relationship between the switches and the destinations is
shown in the table below.
 
2
Finisher adjustment
1)
Enter Simulation 3-10.
2)
Select a set item with [
↑] [↓] buttons. The highlighted section of
the set value is changed and is displayed on the setting area.
* If there is any item over [
↑], the display becomes active and
the cursor can be moved.
If there is no item over [
↑], the display grays out and the
operation is disabled.
If there is any item under [
↓], the display becomes active
and the cursor can be moved.
If there is no item under [
↓], the display grays out and the
operation is disabled.
3)
Enter the set value with 10-key.
* Press [C] key to clear the entered value.
4)
When [OK] button is pressed, it is highlighted and the entered
value is saved to EEPROM and RAM. After completion of set-
ting, [OK] button returns to the normal display.
* When [OK], [
↑], [↓] button, [COLOR], or [BLACK & WHITE]
key is pressed, the current set value is saved to EEPROM
and RAM.
* When the reset key is pressed, the simulation is terminated.
* When [SYSTEM SETTINGS] key is pressed, the display
returns to the sub number entry screen.
<Set range and default value of each set value>
<Variation and change direction of each set value>
JOB No.
Adjustment item list
Simulation 
to be used
1
Punch unit, punch PWB destination setting
2
Finisher adjustment
3-10
3
Flapper solenoid adjustment
4
Punch home position adjustment
Model
Kind of punching
1
2
MX-PNX1A
2-hole type
OFF
OFF
MX-PNX1B
2/3-hole type
ON
OFF
MX-PNX1C
4-hole type (France)
OFF
ON
MX-PNX1D
4-hole type (Sweden)
ON
ON
㪦㪥
Item
Display
Item
Set 
range
Default 
value
A
FRONT 
ADJUST
Alignment position adjustment 
(Front)
2 to 18
10
B
REAR 
ADJUST
Alignment position adjustment 
(Rear)
2 to 18
10
C
STAPLE 
REAR
Staple binding position 
adjustment (One position, rear)
68 to 132
100
D
STAPLE 
FRONT
Staple binding position 
adjustment (One position, front)
68 to 132
100
E
STAPLE 
BOTH
Staple binding position 
adjustment (2 positions, center)
68 to 132
100
F
STAPLE 
PITCH
Staple binding position (2 
positions, pitch)
68 to 132
100
G
PUNCH 
CENTER
Punch center adjustment
37 to 63
50
H
PUNCH 
HOLE
Punch hole position adjustment
42 to 58
50
Item
Display
Item
Variation
Change direction
A
FRONT 
ADJUST
Alignment 
position 
adjustment 
(Front)
0.3665mm
Large value: The 
alignment plate 
position is shifted to 
the center.
Small value: The 
alignment plate 
position is shifted to 
the outside. 
B
REAR 
ADJUST
Alignment 
position 
adjustment 
(Rear)
0.3665mm
Large value: The 
alignment plate 
position is shifted to 
the center.
Small value: The 
alignment plate 
position is shifted to 
the outside.
C
STAPLE 
REAR
Staple binding 
position 
adjustment 
(One position, 
rear)
0.155mm
Large value: The 
distance between the 
staple position and the 
paper edge becomes 
shorter. 
Small value: The 
distance between the 
staple position and the 
paper edge becomes 
longer.
MX-FNX1/MX-PNX1  ADJUSTMENTS  8 – 2
[Screen]
 
3
Flapper solenoid adjustment
When the flapper solenoid is disassembled, an adjustment is
required when assembling. (Disassembly and assembly: Refer to
6-2.)
 
4
Punch home position adjustment
In case the punch unit comes out of order and does not function,
turn the dial to make the punch align to the home position. By mak-
ing the punch align to the home position, only the paper feed
comes possible.
D
STAPLE 
FRONT
Staple binding 
position 
adjustment 
(One position, 
front)
0.155mm
Large value: The 
distance between the 
staple position and the 
paper edge becomes 
longer. 
Small value: The 
distance between the 
staple position and the 
paper edge becomes 
shorter.
E
STAPLE 
BOTH
Staple binding 
position 
adjustment (2 
positions, 
center)
0.155mm
Large value: The 
staple position is 
shifted to the bottom 
from the center.
Small value: The 
staple position is 
shifted to the front 
from the center.
F
STAPLE 
PITCH
Staple binding 
position 
adjustment (2 
positions, pitch)
0.155mm
Large value: The pitch 
of 2 positions 
becomes greater. 
Small value: The pitch 
of 2 positions 
becomes smaller. 
G
PUNCH 
CENTER
Punch center 
adjustment
0.1441mm
Large value: The hole 
position is shifted to 
the bottom from the 
center. 
Small value: The hole 
position is shifted to 
the front from the 
center. 
H
PUNCH 
HOLE
Punch hole 
position 
adjustment
0.2584mm
Large value: The 
distance between the 
hole position and the 
paper rear edge 
becomes shorter. 
Small value: The 
distance between the 
hole position and the 
paper rear edge 
becomes longer. 
Item
Display
Item
Variation
Change direction
0
A:
A: 10
; FRONT ADJUST
B: 10
; REAR ADJUST
C:100
; STAPLE REAR
D:100
; STAPLE FRONT
SIMULATION NO.03-10
FINISHER ADJUSTMENT
10
[
2~ 18 ]
OK
TEST
CLOSE
HOME
Display

Sharp MX-PNX1C (serv.man10) Service Manual ▷ Download

  • DOWNLOAD Sharp MX-PNX1C (serv.man10) Service Manual ↓ Size: 216.16 KB | Pages: 2 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sharp MX-PNX1C (serv.man10) in PDF for free, which will help you to disassemble, recover, fix and repair Sharp MX-PNX1C (serv.man10) Copying Equipment. Information contained in Sharp MX-PNX1C (serv.man10) Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.