DOWNLOAD Sharp MX-M700U (serv.man3) Service Manual ↓ Size: 8.27 MB | Pages: 60 in PDF or view online for FREE

Model
MX-M700U (serv.man3)
Pages
60
Size
8.27 MB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / Installation Manual
File
mx-m700u-sm3.pdf
Date

Sharp MX-M700U (serv.man3) Service Manual ▷ View online

AR-M550/M620/M700  INSTALLATION MANUAL  (AR-M550/M620/M700)  1 - 8
2) Set the manual paper feed guide to the set paper size.
3) Set the paper with print face up and insert until it makes contact
with the manual paper feed guide.
Note: If there is any gap between paper and the manual paper feed
guide, skew feed or wrinkles may be caused. Be sure to set
paper so that there is no gap between paper and the guide.
(4) Tray 2 paper size change
When changing the paper size of the tray 2 from B5 to A4, replace the
guide plate with the A4-exclusive regulation plate.
1) Remove the A4-exclusive regulation plate from the storage position
left inside of the machine. (It is fixed with a fixing screw under the
tab paper guide.)
2) Pull out the tray 1 and the tray 2.
3) Remove the B5 size regulation plate and the rear edge regulation
plates F and R from the tray 2.
When removing the B5 size regulation plate, slightly press the
paper feed base plate downward and press the hook under the reg-
ulation plate to remove.
4) Install the A4 size regulation plate.
5) Supply paper to the tray 2.
6) Push the tray 1 and the tray 2.
Note: Store the B5 size regulation plate and the rear edge regulation
plates F and R for future use.
A4
LT
A4
LT
Specified line
AR-M550/M620/M700  INSTALLATION MANUAL  (AR-M550/M620/M700)  1 - 9
(5) Tray 3 or tray 4 paper size change
1) Pull out the tray 3 or the tray 4.
2) Hold and slide the fixing knob (slide system) of the partition plates A
and B to fit with the size of paper to be supplied.
3) Supply paper into the tray.
4) Push the tray.
Note: Note that a certain special paper cannot be used for the tray 4.
To use the special paper, use the tray 3.
(6) Tab paper setting
To use tab paper, install the exclusive-use guide to the tray 3.
Note that the tray 4 cannot be used.
1) Remove the exclusive-use guide from the storage position left
inside of the machine.
2) Pull out the tray 3.
3) Slide the partition plate to tab paper as shown in the figure below
and install it so that it covers the partition plate.
4) Supply tab paper with the print face up into the tray 3.
5) Push the tray 3.
(7) Setting the paper type and paper size
Follow these steps to change the paper type setting when the paper
type has been changed in a paper tray. For the paper types that can be
used in each tray.
1) Press the [CUSTOM SETTINGS] key.
The custom setting menu screen will appear.
2) Touch the [TRAY SETTINGS] key.
The paper tray selection screen will appear.
3) Display the setting screen of the desired paper tray.
Touch the 
 key or 
 key to display the setting screen of the
desired paper tray.
Note: To automatically switch to a tray with the same size and type of
paper (if there is one) in the event that the paper tray runs out of
paper, display the last screen with the 
 key and select
[AUTO TRAY SWITCHING].
4) Touch the [TYPE / SIZE] key.
TRAY SETTINGS
TA
ORWARD
RINT
PRINTER
CONDITION
1/8
PLAIN / 8 x11
OK
PRINT
TRAY SETTINGS
TYPE / SIZE
CUSTOM SETTINGS
TRAY1
FAX
I-FAX
COPY
DOC. 
FILING
FIXED PAPER 
DISABLE DUPLEX
DISABLE STAPLE
DISABLE PUNCH
/
 2
TYPE / SIZE
TRAY3
TRAY SETTINGS
PRINT
COPY
I-FAX
DOC. 
FILING
FAX
PLAIN / 8 x11
/
 2
AR-M550/M620/M700  INSTALLATION MANUAL  (AR-M550/M620/M700)  1 - 10
5) Select the type of paper that was loaded in the tray.
Example: The paper type of tray 3 is selected.
Touch the desired paper type to select it. The paper size setting
screen will appear.
Notes:
• Tabbed paper can only be used in tray 3 and the bypass tray.
• Label sheet, OHP: Tray 1, 2, 4, and 5 cannot be used.
• Heavy paper: Tray 1, 2, and 5 cannot be used.
6) Select the size of paper that was loaded in the tray.
Touch the appropriate keys (checkboxes).
Note: Sizes that can be selected vary depending on the selected
paper type.
7) Touch the [OK] key in the size setting screen.
You will return to the tray setting screen of step 3.
8) Select output functions that can be used with the selected tray.
Touch the checkboxes under the desired items to select them.
Note: When the inserter (option) is selected, printing of faxes and
Internet faxes is not possible.
User type
Select a "User type" when the name of the paper type does not appear
in the selections or when you wish to select the tray attributes yourself.
Touch the 
 key in step 5 on the previous page to display the user
type selection screen and then select a user type.
9) Set the attributes of the paper tray only if you have selected a user
type. (Touch the checkboxes to the left of the items to select them.)
Notes:
• Paper tray attributes cannot be set when a user type is not selected.
• Tray attributes depend on the selected paper.
• "FIXED PAPER SIDE" and "DISABLE DUPLEX" cannot be simulta-
neously enabled.
10) Configure paper settings for each tray and then touch the [OK] key
to exit.
Note: The size and type of paper loaded in the bypass tray can also
be set from the paper setting screen. Touch the [PAPER
SELECT] key in the main screen to display the paper selection
screen, and then touch the [PAPER SELECT] key of the bypass
tray and go to step 5.
(8) Setting the paper size when a special size is loaded
Note: Special sizes of paper cannot be loaded in trays 1, 2, 4 and 5.
[Trays 3 and the bypass tray]
1) Perform steps 1 through 5 of "Setting the paper type and paper
size".
2) Touch the [SIZE INPUT] key and then touch the [INCH] tab. 
(The size entry palette appears.)
3) Touch the 
 key or the 
 key to enter the X (width) and Y
(length) dimensions of the paper.
X (width) is initially selected. To enter Y (length), touch the [Y] key
and then enter the length.
[AUTO-INCH] key: Select when you have loaded an inch-based 
size of paper.
[AUTO-AB] key:
Select when you have loaded an AB size of 
paper.
[SIZE INPUT] key: Select to directly enter a paper size.
[NON STANDARD 
SIZE] checkbox:
Select when you have loaded a non-standard 
size of paper.
CANCEL
1/2
PLAIN
RECYCLED
PRE-PRINTED
PRE-PUNCHED
LETTER HEAD
COLOR
HEAVY PAPER
TAB PAPER
LABELS
TRANSPARENCY
TRAY 3 TYPE/SIZE SETTING
SELECT THE PAPER TYPE.
CUSTOM SETTINGS
1/2
11X17,8 X14,8 X11
8 X11R,7 X10 ,5 X8 R
/
 2
/
 2
/
 2
/
 2
/
 4
/
 2
/
 2
A3,A4,A4R,A5R,B4,B5
B5R,216X330(8 X13)
/
 2
TYPE
OK
PLAIN
TRAY3 TYPE/SIZE SETTING
CUSTOM SETTINGS
TYPE
AUTO-INCH
SIZE INPUT
AUTO-AB
SIZE
X     Y 
NON STANDARD 
SIZE
2/2
PRINT
COPY
FAX
I-FAX
DOC. 
FILING
CUSTOM SETTINGS
TRAY 3 TYPE/SIZE SETTING
2/2
USER TYPE 1
CANCEL
SELECT THE PAPER TYPE
USER TYPE 5
USER TYPE 2
USER TYPE 6
USER TYPE 3
USER TYPE 7
USER TYPE 4
1/2
"FIXED 
PAPER SIDE":
Select when paper is to be loaded print side down 
in the tray.
Make sure a checkmark does not appear when 
paper is to be loaded print side up.
• If the two-sided function is prohibited in 
"DISABLING OF DUPLEX" in the key operator 
programs, do not use this setting.
"DISABLE 
DUPLEX":
Prohibits two-sided printing.
Enable when the back side of the paper cannot be 
printed on.
"DISABLE 
STAPLE":
Prohibits stapling. Enable when using special 
papers such as transparency film and label sheets.
"DISABLE 
PUNCH":
Prohibits punching. Enable when using special 
papers such as transparency film and label sheets.
FIXED PAPER SIDE
DOC. 
FILING
DISABLE DUPLEX
DISABLE STAPLE
DISABLE PUNCH
AB
Y
11
17
X
(5 1/2 17)
inch
INCH
OK
(5 1/2 11 5/8)
inch
Y
X
AB
Y
11
17
Y
X
INCH
OK
(5 1/2 17)
inch
(5 1/2 11 5/8)
inch
: Feb. 9 2004
2
AR-M550/M620/M700  INSTALLATION MANUAL  (AR-M550/M620/M700)  1 - 11
4) Touch the [OK] key. (You will return to the size setting screen of
step 2.)
5) If the paper is a non-standard size, select the [NON STANDARD
SIZE] checkbox.
6) Perform steps 7 through 10 of "Setting the paper type and paper
size".
[Inserter (option)]
1) Perform steps 1 through 5 of "Setting the paper type and paper
size".
2) Touch the [SIZE SELECT] key. (The size selection screen
appears.)
Note: When tabbed paper is selected, the [NON STANDARD SIZE]
checkbox of the [SIZE SELECT] key cannot be selected.
3) Select the desired paper size.
There are separate screens for inch-based paper selection and AB
paper selection. Touch the 
 key or the 
 key to switch
between the screens.
4) Touch the [OK] key. (You will return to the size setting screen of
step 2.)
5) Perform steps 7 through 10 of "Setting the paper type and paper
size".
H. The other parts setting
(1) Document exit tray installation
Install the document exit tray to the scanner unit as shown in the figure
below.
(2) Other notes
Check to insure that the cable connected to the service terminal (A in
the figure below) is 3m or less.
X
AB
Y
11
17
Y
X
INCH
OK
(5 1/2 17)
inch
(5 1/2 11 5/8)
inch
NON STANDARD
SIZE
11
X
17,8 
X
14,8 
X
11
/
 2
/
 2
X
11R,7 
X
10 ,5 
X
8 R
/
 2
/
 4
/
 2
/
 2
/
 2
A3,A4,A4R,A5R,B4,B5
B5R,216x330(8 x13)
X17  Y11
/
 8
/
 2
SIZE SELECT
11
X
17,8 
X
14,8 
X
/
 2
/
 2
X
11R,7 
X
10 ,5
/
 2
/
 4
 
/
 2
A3,A4,A4R,A5R,B
AUTO-INCH
AUTO-AB
B5R
1/2
PLAIN
11X17
OK
TYPE
INSERTER TYPE/SIZE SETTING
TYPE
CUSTOM SETTINGS
8 X14
/
 2
8 X11
/
 2
8 X11R
/
 2
7 X10
/
 4
/
 2
5 X8 R
/
 2
/
 2
SIZE
8 X14
/2
X10 
/4
/
 2
1/2
TYPE
8 X11
/
 2
5 X8 R
/
 2
/
 2
SIZE
OK
4. Cleaning
A. Main charger
1) Reciprocate the MC cleaner shaft back and forth to clean the elec-
trode tip.
(A)
2
Page of 60
Display

Click on the first or last page to see other MX-M700U (serv.man3) service manuals if exist.