Sharp MX-M700U (serv.man3) Service Manual ▷ View online
AR-M550/M620/M700 INSTALLATION MANUAL (AR-M550/M620/M700) 1 - 2
(2) Dust
If dust enters the machine, it may cause dirty copy and a paper jam,
resulting in a shortened lifetime.
resulting in a shortened lifetime.
(3) Direct rays of the sun
If the machine is installed under the rays of the sun, the exterior of the
machine may be discolored and abnormal copies may be produced.
machine may be discolored and abnormal copies may be produced.
(4) Gases and chemicals
Do not install the machine at a place where there are gases and chem-
icals. Especially be careful to avoid installation near a diazo-type
copier, which produces ammonium gas.
icals. Especially be careful to avoid installation near a diazo-type
copier, which produces ammonium gas.
Copy quality may be adversely affected and a trouble may be caused.
(5) Vibration
Avoid installation near a machine which produces vibrations.
If vibrations are applied to the copier machine, copy images may be
deflected and a trouble may be caused.
deflected and a trouble may be caused.
2. Transit and delivery
A. Implements, facility, and manpower
It is recommendable to use a forklift for bringing in the machine for
safety.
safety.
If no forklift is available, manpower of four or more persons is required.
The machine is considerably heavy, and requires safety precautions
for delivery and installation.
The machine is considerably heavy, and requires safety precautions
for delivery and installation.
Transit of the machine must be made in packed condition to the install-
ing place.
ing place.
B. Delivery
Remove the packing materials prior to installation in the ofice environ-
ment.
ment.
3. Unpacking
A. Unpacking procedure
1) Remove the PP band.
2) Remove the top case.
3) Remove the internal packing pads and the items packed together
with the machine.
No.
Content
Method
1
Implements, facility,
and manpower
and manpower
Use a forklift. (If no forklift is available,
manpower of four or more persons is
required.)
manpower of four or more persons is
required.)
2
Delivery
Transit must be made in packed
condition.
condition.
1
PP band
7
Polyethylene bag
2
Top case
8
Bottom case unit
3
Pack case
9
Accessory unit
4
Skid pad
10
Paper exit tray AS
5
Top pad R
11
Operation manual
6
Top pad L
AR-M550/M620/M700 INSTALLATION MANUAL (AR-M550/M620/M700) 1 - 3
4) Remove the adjuster cover and the screw (in the bag).
5) Cut the four corners of the bottom case.
6) Lift the machine slightly, and remove the bottom pad L.
7) Lift the machine slightly, and remove the bottom pad R.
8) Remove the slope.
∗
Slope: Parts
9) Attach the slope to the concave section of the skid.
10) Hold the machine grips and push them down in the arrow direc-
tion.
Part name
Part code
Skid slope
DKiT-0367FCZZ
: Feb. 9 2004
2
AR-M550/M620/M700 INSTALLATION MANUAL (AR-M550/M620/M700) 1 - 4
B. Adjuster cover installation
1) Move the main unit to the installing position, and turn the adjuster to
fix the main unit.
2) Remove the bottom tray from the main unit.
3) Install the adjuster cover to the main unit.
4)
Insert the bottom tray into the main unit.
Note: This machine includes a hard disk drive, which must be pro-
tected against vibrations and shocks.
Never move the machine with the power ON.
Packed items
C. Remove the fixing tape and the reinforcing
material
2
1
Driver (CD-ROM)
x 1
2
Operation manual
x 1
3
Delivery and installation report
x 1
4
Paper exit tray
x 1
1
2
3
4
AR-M550/M620/M700 INSTALLATION MANUAL (AR-M550/M620/M700) 1 - 5
D. Lock release
(1) No. 2/3 mirror base lock release
Remove the No. 2/3 mirror base fixing screw and the label of note for
unpacking on the left side.
unpacking on the left side.
(2) Tray rotation release plate lock release
Remove the paper feed tray rotation plate fixing screw and the label of
note for tray.
note for tray.
[Tray 1, Tray 2]
[Tray 3, Tray 4]
E. Press the fusing section (upper and lower heat
rollers) and remove the process separation pawl
fixing block.
fixing block.
1) Pull the knob on the left door to pull out the left door.
2) Turn the pressing screw in the fusing section as shown in the figure
below (fully loosen it) to press the heat roller.
3) Remove the separation pawl fixing block from the process unit.
4) Replace the left door.
Lock position
1
No. 2/3 mirror base lock screw
2
Tray rotation plate fixing material
2
