Sharp MX-M654N / MX-M754N (serv.man2) Handy Guide ▷ View online
CONSUMABLES
SHARP
10
TRANSFER SECTION:
MX-M654N, MX-M754N
Product Code
Description / Contents
Approx. Life
MX-754TT
Transfer Belt Kit:-
Transfer belt
Transfer roller
Transfer drive gear
Transfer CL gear
Transfer roller bearing x 2
400k
PERIPHERALS:
MX-SCX1
Staple Cartridge for MX-FN17,
Saddle Staple Cartridge for MX-FN22
Saddle Staple Cartridge for MX-FN22
5000 staples (x 3)
MX-SCX2
Staple Cartridge for MX-FN21/MX-FN22
5000 staples (x 3)
AR-SC2
Staple Cartridge for MX-FN19/MX-FN20
5000 staples (x 3)
AR-SC3
Saddle Staple Cartridge for MX-FN20
2000 staples (x 3)
AR-SV1
Stamp Cartridge for AR-SU1
2 cartridges
SERVICE ROTATION:
MX-754FU
Fusing Unit (230v)
Field Rotation (400k)
Notes:
* The consumable life is specified by 840K rotations therefore, the page count life indicated above is for
approx. guidance only.
Also, consumable life may vary depending on the document density, temperature, humidity and machine
operation.
SHARP
INITIAL SETUP
11
DEVELOPER INSTALLATION & SET-UP
Sim 25-02 Auto Developer Adjustment - Select K.
Toner Installation must be performed after Auto Developer Adjustment is completed.
**For optimum quality & performance, setup & install developer at the customer site.
TONER INSTALLATION & REPLENISHMENT
Install K Toner Cartridge
Caution:
DO NOT open any Exterior Cover, Power OFF/ON or enter Simulation Mode during
Initial Toner Replenishment.
DO NOT open any Exterior Cover, Power OFF/ON or enter Simulation Mode during
Initial Toner Replenishment.
PRODUCT OPTION ACTIVATION
Activation of Optional Product(s):-
System Settings – Administrator Mode – Product Key.
FIRMWARE UPGRADE [ALL]
Sim 22-05 Check Firmware version(s):-
Upgrade to latest version.
INITIAL SETUP
Sim 26-01 Right Tray Installation
Yes/No.
Sim 26-02 LCC Installation (Paper Size):-
A4.
Sim 26-06 Machine Destination.
Sim 26-35 Set Multi Error Counter
Set to 1 (Multi Count).
Sim 26-50 Long Paper Support (up to 1200mm),
0 = Disable, 1 = Enable
.
Sim 26-52 Non Printed Paper Counter Set-up.
Sim 55-03 Process Mixed Size Pages (orientation) when Printing in Duplex:-
SSW 3-6,
0 = Disable, 1 = Enable.
Sim 55-03 Toner Remain Status Display: SSW 22-5,
0 = Disable, 1 = Enable.
System Settings: Adjust Date/Time (Inc. Daylight Saving setting).
Keyboard Language Setting (For Embedded & Optional Keyboards):-
System Settings – Default Settings – Keyboard Select: Set English(US)
Network Settings – Print Port Settings: Disable WSD.
Set cassette size by adjusting the guides in the cassette.
Paper Size & Type Setting:-
Paper Size & Type Setting:-
System Settings – Paper Tray Settings.
IMAGE SKEW [ENGINE]
Sim 64-02 Check LSU Parallelism.
Select A=1, B=1, C=254, D=255
INITIAL SETUP
SHARP
12
PRINT IMAGE POSITION & MAGNIFICATION
Sim 50-28 BK MAG ADJ (Main Scan Mag).
SETUP/PRINT ADJ (Lead, Offset or All).
MANUAL ADJUSTMENT:-
Sim 50-10 BK MAG (inside dimension) to 240mm.
Sim 50-10 Image Off Centre Adjustment.
Sim 50-05 Printer Lead Edge & Void Adjust.
HALF TONE CALIBRATION
Sim 46-74 Engine & Printer Calibration
Select FACTORY Mode
COPY IMAGE QUALITY
Check Image Quality (Copy Mode) – Density, Magnification, Lead Edge & Void.
If NG, perform the following adjustments as required:-
Sim 46-02 Copy Density Adjust.
Sim 46-09 SPF Copy Density Adjust.
Sim 50-28 OC ADJUST (Lead, Offset & Mag).
SPF ADJ:(Lead, Offset & Sub scan).
Manual Adjustment (Magnification, Lead Edge, Void, Off Centre etc).
Sim 48-01 Magnification Adjustment (OC & SPF).
Sim 50-01 Lead/Rear Edge, Loss & Void Adjust.
Sim 50-12 OC & SPF Off Centre Adjust.
PRINT IMAGE QUALITY
Check Image Quality (Print Mode) – Density.
Sim 64-05 PCL Density Test Page
Sim 64-06 PS Density Test Page
PERIPHERAL / OPTION CONFIGURATION
FAX OPTION – MX-FX11
Sim 66-02 Fax SW Setting (Destination).
Sim 66-10 Fax Memory Clear (For Extended Memory).
Sim 66-39 Fax Destination Set.
SHARP
INITIAL SETUP
13
PERIPHERAL / OPTION CONFIGURATION
FINISHER OPTION – MX-FN17, MX-FN19, MX-FN20, MX-FN21, MX-FN22
Sim 03-10 Saddle Fold/Staple Position Adjustment [MX-FN20/22 only]
Sim 26-65 Finisher Alarm Mode:-
Limit number of Copies in staple mode
(ON/OFF).
EXTERNAL ACCOUNTING MODULE – MX-AMX3
Sim 55-03 Auto clear function before Copy job execution:-
SSW 1-5
0 = Disable, 1 = Enable.
Sim 55-03 Continuous print mode (job queuing for OSA):-
SSW 24-7
0 = Disable, 1 = Enable.
MFP DATA BACKUP
Sim 22-06 Data Simulation Print.
Device Clone & Storage Backup.
Sim 56-01 Backup EEPROM Data to HDD.
Click on the first or last page to see other MX-M654N / MX-M754N (serv.man2) service manuals if exist.