Sharp MX-M623U / MX-M753U (serv.man79) Service Manual / Technical Bulletin ▷ View online
Sharp Electronics (UK) Ltd., Document Systems Support
[Description]
No.
Details
1
Under the following conditions the consistency of the paper ejected to the ejection tray has been
improved.
improved.
- Ejecting non-sort/mixed loading
- Ejecting large size paper to the middle tray
- Ejecting 10 pages or more for a single batch
- Ejecting letter and B5 paper
2
For inserter offline jobs, even if "Staple" is specified, if a batch only has one page the stapling will not
occur.
occur.
3
Repeating A5R job in non-sort mode could cause an F1-81 error (Relay vertical sending motor error). This
glitch has been corrected.
glitch has been corrected.
4
When ejecting paper automatically, the end edge of the paper can remain at the ejection roller. This can
cause shutter trouble when the next job starts. This glitch has been corrected.
cause shutter trouble when the next job starts. This glitch has been corrected.
5
For multiple part letter and staple jobs, using gripper ejection can sometimes cause and FDRLM jam
(ejection roller lift motor jam). This glitch has been corrected.
(ejection roller lift motor jam). This glitch has been corrected.
6
After resolving ejection guide and front cover open jam and then when the front cover is closed, the panel
now displays a message to close the ejection guide.
now displays a message to close the ejection guide.
Sharp Electronics (UK) Ltd., Document Systems Support
[Description]
No.
Details
1
Under the following conditions the consistency of the paper ejected to the ejection tray has been
improved.
improved.
- Ejecting non-sort/mixed loading
- Ejecting large size paper to the middle tray
- Ejecting 10 pages or more for a single batch
- Ejecting letter and B5 paper
2
For inserter offline jobs, even if "Staple" is specified, if a batch only has one page the stapling will not
occur.
occur.
3
Repeating A5R job in non-sort mode could cause an F1-81 error (Relay vertical sending motor error). This
glitch has been corrected.
glitch has been corrected.
4
When ejecting paper automatically, the end edge of the paper can remain at the ejection roller. This can
cause shutter trouble when the next job starts. This glitch has been corrected.
cause shutter trouble when the next job starts. This glitch has been corrected.
5
For multiple part letter and staple jobs, using gripper ejection can sometimes cause and FDRLM jam
(ejection roller lift motor jam). This glitch has been corrected.
(ejection roller lift motor jam). This glitch has been corrected.
6
After resolving ejection guide and front cover open jam and then when the front cover is closed, the panel
now displays a message to close the ejection guide.
now displays a message to close the ejection guide.
Sharp Electronics (UK) Ltd., Document Systems Support
[Description]
No.
Details
1
Under the following conditions the consistency of the paper ejected to the ejection tray has been
improved.
improved.
- Ejecting non-sort/mixed loading
- Ejecting large size paper to the middle tray
- Ejecting 10 pages or more for a single batch
- Ejecting letter and B5 paper
2
For inserter offline jobs, even if "Staple" is specified, if a batch only has one page the stapling will not
occur.
occur.
3
Repeating A5R job in non-sort mode could cause an F1-81 error (Relay vertical sending motor error). This
glitch has been corrected.
glitch has been corrected.
4
When ejecting paper automatically, the end edge of the paper can remain at the ejection roller. This can
cause shutter trouble when the next job starts. This glitch has been corrected.
cause shutter trouble when the next job starts. This glitch has been corrected.
5
For multiple part letter and staple jobs, using gripper ejection can sometimes cause and FDRLM jam
(ejection roller lift motor jam). This glitch has been corrected.
(ejection roller lift motor jam). This glitch has been corrected.
6
After resolving ejection guide and front cover open jam and then when the front cover is closed, the panel
now displays a message to close the ejection guide.
now displays a message to close the ejection guide.
Sharp Electronics (UK) Ltd., Document Systems Support
[Description]
No.
Details
1
Under the following conditions the consistency of the paper ejected to the ejection tray has been
improved.
improved.
- Ejecting non-sort/mixed loading
- Ejecting large size paper to the middle tray
- Ejecting 10 pages or more for a single batch
- Ejecting letter and B5 paper
2
For inserter offline jobs, even if "Staple" is specified, if a batch only has one page the stapling will not
occur.
occur.
3
Repeating A5R job in non-sort mode could cause an F1-81 error (Relay vertical sending motor error). This
glitch has been corrected.
glitch has been corrected.
4
When ejecting paper automatically, the end edge of the paper can remain at the ejection roller. This can
cause shutter trouble when the next job starts. This glitch has been corrected.
cause shutter trouble when the next job starts. This glitch has been corrected.
5
For multiple part letter and staple jobs, using gripper ejection can sometimes cause and FDRLM jam
(ejection roller lift motor jam). This glitch has been corrected.
(ejection roller lift motor jam). This glitch has been corrected.
6
After resolving ejection guide and front cover open jam and then when the front cover is closed, the panel
now displays a message to close the ejection guide.
now displays a message to close the ejection guide.
Display