DOWNLOAD Sharp MX-M623U / MX-M753U (serv.man7) Service Manual ↓ Size: 13.53 MB | Pages: 104 in PDF or view online for FREE

Model
MX-M623U MX-M753U (serv.man7)
Pages
104
Size
13.53 MB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / INSTALLATION MANUAL.
File
mx-m623u-mx-m753u-sm7.pdf
Date

Sharp MX-M623U / MX-M753U (serv.man7) Service Manual ▷ View online

MX-M753N  MX-M623N/M623U/M753N/M753U  1 – 1
MX-M753N
Service Manual
 
[1] MX-M623N/M623U/M753N/
M753U
1.  Installing (use) conditions
Before installing the machine, check that the following installing
(use) conditions are satisfied.
If the installing (use) conditions are not satisfied, the machine may
not display full performances, resulting in troubles. It may also
cause safety problems. Therefore, be sure to arrange the installing
(use) conditions before setting up the machine.
A. Bringing space
For installation of a large size machine, be sure to check that the
door size is wide enough before bringing in.
B. Installing space
The following space must be provided around the machine in order
to assure machine performances and proper operations.
If any option is installed, provide the additional space for installing
it.
Adequate space must be provide behind the machine for proper
ventilation heat and dust. If not, the machine cannot exhibit func-
tions against heat and dust, causing some troubles.
C. Power source (Capacity, voltage, frequency, 
safety, plug)
If the power specifications are not satisfied, the machine cannot
exhibit full performances and may cause safety trouble.
Strictly observe the following specifications.
(1) Power capacity
Check that the following power capacity is satisfied. If not, addition-
ally provide a power source.
Current capacity
Japan: 20A or more
100V: 15A or more
200V: 10A or more
NOTE: Check the shape of the power plug of the machine, and
insert it into a power outlet of the acceptable shape.
(2) Power voltage
Measure the voltage during copying to check that the voltage is in
the range of the specified voltage 
±10%.
If the voltage is outside the specified range, use thicker lead wires
to reduce impedance.
(An electrical work is required.)
Use of a step-up transformer is also available. In this case, the
capacity must be great enough for the max. power consumption of
the machine.
(3) Power frequency, waveform
The frequency must be within the range of the specified frequency
±2%. If power waveform is deformed, a trouble may occur.
(4) Safety
Be sure to properly ground the machine.
Grounding (earth connection) must be performed before inserting
the power plug into the power outlet.
When disconnecting the earth connection, be sure to disconnect
the power plug from the power outlet in advance.
(5) Power plug
Check the shape of the power plug of the machine, and insert it into
a power outlet of the acceptable shape.
D. Floor strength and level
This machine is considerably heavy and becomes heavier with an
option installed.
The floor must be strong enough for assuring safety.
If the unit is not horizontally installed, the toner density control is not
performed normally, degrading the copy quality.
If not, color shift or image distortion may occur.
E. Direct rays of the sun, dust, temperature, 
humidity, gasses, chemicals, vibration
(1) Temperature and humidity
This machine is designed to perform properly under the specified
temperature and humidity. If the temperature and humidity exceeds
the specified range, the machine may not operate properly and or
cause equipment failure.
Especially when the humidity is too high, paper absorbs humidity to
cause a paper jam or dirty copy.
Do not install the machine near a heater, a cooler, or a humidifier.
Dew may be formed inside the machine to cause a trouble. Use
enough care for ventilation.
• Working environment
Temperature: 10 to 35
°C
Humidity: 20 to 85% RH
Atmospheric pressure: 590 to 1013hPa (altitude: 0 to 2000 m)
No.
Content
1
Bringing space
2
Installing space
3
Power source (Capacity, fluctuation, safety)
4
Floor strength
5
Direct rays of the sun, dust, temperature, humidity, gases, 
chemicals
17-23/32"
(45cm)
11-13/16"
(30cm)
11-13/16"
(30cm)
85%
Humidity㧔RH㧕
60%
20%
MX-M753N  MX-M623N/M623U/M753N/M753U  1 – 2
(2) Dust
If dust enters the machine, it may cause dirty copy and a paper
jam, resulting in a shortened lifetime.
(3) Direct rays of the sun
If the machine is installed under the rays of the sun, the exterior of
the machine may be discolored and abnormal copies may be pro-
duced.
(4) Gases and chemicals
Do not install the machine at a place where there are gases and
chemicals. Especially be careful to avoid installation near a diazo-
type copier, which produces ammonium gas.
Copy quality may be adversely affected and a trouble may be
caused.
(5) Vibration
Avoid installation near a machine which produces vibrations.
If vibrations are applied to the copier machine, copy images may be
deflected and a trouble may be caused.
F. Note for handling PWB and electronic parts
When handling the PWB and the electronic parts, be sure to
observe the following precautions in order to prevent against dam-
age by static electricity.
1)
When in transit or storing, put the parts in an anti-static bag or
an anti-static case and do not touch them with bare hands.
2)
When and after removing the parts from an anti-static bag
(case), use an earth band as shown below:
• Put an earth band to your arm, and connect it to the
machine.
• When repairing or replacing an electronic part, perform the
procedure on an anti-static mat.
MX-M753N  MX-M623N/M623U/M753N/M753U  1 – 3
G. Note for handling the drum unit, the transfer 
unit, the developing unit, and the fusing unit
When handling the OPC drum unit, the transfer unit, and the devel-
oping unit, strictly observe the following items.
If these items are neglected, a trouble may be generated in the
copy and print image quality.
(Drum unit)
1)
Avoid working at a place with strong lights.
2)
Do not expose the OPC drum to lights including interior lights
for a long time.
3)
When the OPC drum is removed from the machine, cover it
with light blocking material. (When using paper, use about 10
sheets of paper to cover it.)
4)
Be careful not to attach fingerprints, oil, grease, or other for-
eign material on the OPC drum surface.
(Transfer unit)
1)
Be careful not to attach fingerprints, oil, grease, or other for-
eign material on the transfer roller.
(Developing unit)
1)
Be careful not to attach fingerprints, oil, grease, or other for-
eign material on the developing unit.
(Fusing unit)
1)
Be careful not to put fingerprints, oil, grease, or other foreign
material on the fusing roller and the external heating belt.
2)
Do not leave the fusing roller in contact state for a long time.
2.  Transit and delivery
A. Implements, facility, and manpower
It is recommended to use a forklift for bringing in the machine for
safety.
If no forklift is available, man-power of two persons is required. The
machine is considerably heavy, and requires safety precautions for
delivery and installation.
Transit of the machine must be made in packed condition to the
installing place.
Since the hard disk drive is built in the machine, use care not to
exert vibrations or shocks to the machine when in transit.
B. Delivery
Remove the packing materials prior to installation in the office envi-
ronment.
3.  Unpacking
A. Unpacking procedure
1)
Remove the PP band.
2)
Remove the top case.
3)
Remove the top pads.
4)
Remove the adjuster cover and the screw (in the bag) from the
top pad L.
5)
Lift the machine slightly, and remove the bottom pad L.
6)
Lift the machine slightly, and remove the bottom pad R.
No.
Content
Method
1
Implements, facility, 
and man power
Use a forklift. (If no forklift is available, 
manpower of two persons is required.) 
2
Delivery
Transit must be made in packed condition.
MX-M753N  MX-M623N/M623U/M753N/M753U  1 – 4
7)
Remove the slope.
* Slope: Parts
8)
Attach the slope to the concave section of the skid.
9)
Hold the machine grips and push them down in the arrow
direction.
NOTE: This machine includes a hard disk drive, which must be
protected against vibrations and shocks. 
Never move the machine with the power ON.
NOTE: When the machine is moved over a bump, hold the grip on
the right side of the machine to lift and cross the bump
over. This is because the casters may be broken for a big
bump.
B. Removal of the fixing tape, protection material 
and parts packed together
C. Check the parts packed together
1)
Check that all the parts are in the package.
Part name
Part code
Skid slope
DKiT-0367FCZZ
1
Adjuster cover
x 1
2
Adjuster cover fixing screw
x 3
3
Operation manual storage cover
x 1
4
Driver (CD-ROM)
x 1
5
Operation manual
x 1
6
Delivery and installation report
x 1
1
2
3
4
5
6
Page of 104
Display

Click on the first or last page to see other MX-M623U / MX-M753U (serv.man7) service manuals if exist.