Sharp MX-M623U / MX-M753U (serv.man6) Handy Guide ▷ View online
Initial Set-up
Paper pickup
MX-753DF
DSPF roller Kit:-
•
DSPF Paper feed roller
•
DSPF Pick up roller
•
DSPF Separation roller
100K
AR620RT
Paper feed roller Kit:-
•
Paper feed roller
•
Paper pickup roller
•
Paper separation roller
100K
Peripherals
MX-SC10
MX-SC10
100 sheet Staple cartridge for MX-FN14
5,000 x 3
SF-SC11
50 sheet staple cartridge for MX-FN15/16
5,000 x 3
AR-SC3
Saddle finisher staple cartridge for MX-FN16
2,000x 3)
AR-SV1
Ink Cartridge for stamp unit for AR-SU1
2 Cartridges
Note: The consumable life may vary, depending on document density, temperature, humidity
and machine operation.
Initial Set-up
UNPACKING AND LOCK REMOVAL
Remove from pallet using skid ramps
part number :- DKiT-0367FCZZ.
part number :- DKiT-0367FCZZ.
Remove
scanner
locking
screw.
DEVELOPER INSTALLATION
Sim 25-02
Auto Developer Adjustment
Note: Toner Installation should be performed after
Auto Developer Adjustment is completed
**For optimum image quality, it is recommended to
setup/install developer at the customer site.
INITIAL SETTINGS
Sim 26-01
Right Tray Installation Yes/No.
Sim 26-02
LCC Paper Size Set-up.
Sim 26-06
Machine Destination.
Sim 26-35
Set Multi Error Counter Set to 1 (Multi Count).
Sim 26-52
Blank Page Counter Set-up.
Sim 26-65
Finisher Alarm Mode:-
Limit number of Copies in staple mode (ON/OFF).
Limit number of Saddle Copies (ON/OFF).
PRODUCT ACTIVATION & FIRMWARE
Activation of Optional Product(s):-
System Settings – Administrator Mode – Product Key
Sim 22-05 Check Firmware version(s):- Upgrade to latest version.
Note: 1 bag of dev
only.
Initial Set-up
CASSETTE SETUP & PAPER TYPE
Set cassette size by adjusting the guides in the cassettes 3 & 4.
Paper Size & Type Setting:- System Settings – Paper Tray Settings
Paper Size & Type Setting:- System Settings – Paper Tray Settings
PRINT IMAGE SKEW
Sim 64-02 Image Writing Adjustment.
Select A=1, B=1, C=254, D=255
Use A3 Paper
PRINT IMAGE MAGNIFICATION
Automatic Adjustment:-
Sim 50-28 BK MAG ADJ (Main Scan Mag.)
Manual Adjustment:-
Sim 50-10 Adjust BK MAG (inside dimension) to 240mm
Sim 50-10 Image Off Centre Adjustment
Sim 50-05 Printer Lead Edge & Void Adjust
Sim 50-10 Adjust BK MAG (inside dimension) to 240mm
Sim 50-10 Image Off Centre Adjustment
Sim 50-05 Printer Lead Edge & Void Adjust
COPY MAGNIFICATION & IMAGE POSITION
Automatic Adjustment:-
Sim 50-28
Sim 50-28
OC ADJUST (Lead, Offset & Mag.)
Manual Adjustment:-
Sim 48-01
Sim 48-01
Magnification Adjustment (OC).
Sim 50-01
Lead/Rear Edge, Image Loss &void.
Sim 50-12
OC Off Centre Adjust.
DSPF IMAGE POSITION & VOID
Automatic Adjustment:-
Sim 50-28 SPF ADJ:(Lead, Offset & Sub scan)
Manual Adjustment:-
Sim 50-06 SPF Lead Edge Adjust.
Sim 50-12 SPF Off Centre Adjust.
Initial Set-up
ENGINE & PRINTER HALF-TONE - CALIBRATION
Sim 46-24
Automatic Half Tone Calibration
Select FACTORY Mode.
Note: Engine & Printer Half Tone Calibration is performed
together (ie. One scan) and must be completed.
together (ie. One scan) and must be completed.
IMAGE DENSITY
Sim 46-02 Copy Exposure Adjust.
Sim 46-04 Scanner Density Adjust (Colour).
Sim 46-05 Scanner Density Adjust (Mono).
Sim 46-09 DSPF Copy Density Adjust.
PRINTER DENSITY
Sim 64-05 PCL Density Test Page.
Sim 64-06 PS Density Test Page.
(when PS option is installed)
FAX OPTION (MX-FXX2)
Sim 66-02 Fax SW Setting (Destination).
Sim 66-10 Fax Memory Clear (For Extended
Memory).
Sim 66-39 Fax Destination Set.
Sim 66-10 Fax Memory Clear (For Extended
Memory).
Sim 66-39 Fax Destination Set.
FINISHER OPTION (MX-EBX3)
Sim 22-05 ACRE firmware ver 03.00.j2(or higher)
Click on the first or last page to see other MX-M623U / MX-M753U (serv.man6) service manuals if exist.