DOWNLOAD Sharp MX-M364N / MX-565N (serv.man125) Service Manual ↓ Size: 440.04 KB | Pages: 4 in PDF or view online for FREE

Model
MX-M364N MX-565N (serv.man125)
Pages
4 Few pages! See other manuals at the bottom of the first or last page.
Size
440.04 KB
Type
PDF
Document
Service Manual / Technical Bulletin
Brand
Device
Copying Equipment / COUNTERMEASURE FOR TONER CONTAMINATION ON CENTRE OF BACK SIDE OF PAPER.
File
mx-m364n-mx-565n-sm125.pdf
Date

Sharp MX-M364N / MX-565N (serv.man125) Service Manual / Technical Bulletin ▷ View online

1. Open the upper cover.
2. Remove the upper cover stay
Open  the upper guide more than 90-degree 
     Unfasten the screws (x 2) and remove the upper cover stay.
while pushing it forward.
Springs that should be replaced.
3. Replace the springs.
Springs for countermeasure (x 2)
(3-1) Remove the current springs.
(3-2) Mount the springs for countermeasure.
 
1/2
FN10 Spring  Replacement Procedure 
Lower hook  
Upper hook 
Section where to hook. 
(The plate springs of the rear side are fastened 
together.  When removing  the upper cover stay 
please be careful not to drop the plate springs.)  
Unhook the lower hook of the spring that is mounted.  
Then pull the upper hook from the shaft and take it off. 
Dispose of the removed springs. 
Hook the lower hook. 
4. Mount the upper cover stay.
Rear side: Plate spring + screw
2/2
Mount the upper cover.
Front side: Screw (x1)
Close the upper cover.
Be sure not to forget to set the shaft 
of actuator.
Replaced springs. 
Hook the springs to the outer side than the springs at the opposite side that 
are hooked on the same shaft. 
Hook the upper hook to the shaft. 
4. Mount the upper cover stay.
Rear side: Plate spring + screw
2/2
Mount the upper cover.
Front side: Screw (x1)
Close the upper cover.
Be sure not to forget to set the shaft 
of actuator.
Replaced springs. 
Hook the springs to the outer side than the springs at the opposite side that 
are hooked on the same shaft. 
Hook the upper hook to the shaft. 
4. Mount the upper cover stay.
Rear side: Plate spring + screw
2/2
Mount the upper cover.
Front side: Screw (x1)
Close the upper cover.
Be sure not to forget to set the shaft 
of actuator.
Replaced springs. 
Hook the springs to the outer side than the springs at the opposite side that 
are hooked on the same shaft. 
Hook the upper hook to the shaft. 
Display

Sharp MX-M364N / MX-565N (serv.man125) Service Manual / Technical Bulletin ▷ Download

  • DOWNLOAD Sharp MX-M364N / MX-565N (serv.man125) Service Manual ↓ Size: 440.04 KB | Pages: 4 in PDF or view online for FREE
  • Here you can View online or download the Service Manual / Technical Bulletin for the Sharp MX-M364N / MX-565N (serv.man125) in PDF for free, which will help you to disassemble, recover, fix and repair Sharp MX-M364N / MX-565N (serv.man125) Copying Equipment. Information contained in Sharp MX-M364N / MX-565N (serv.man125) Service Manual / Technical Bulletin (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.