Sharp MX-M266N / MX-M316N / MX-M356N Handy Guide ▷ View online
INITIAL SETUP
SHARP
8
DEVELOPER SETUP & TONER INSTALLATION
Sim 25‐02 Auto Developer Adjustment.
Toner cartridge must be installed before execution.
PRODUCT OPTION ACTIVATION
Activation of Optional Product(s):‐
System Settings – Administrator Mode – Product Key.
FIRMWARE UPGRADE [ALL]
Sim 22‐05 Check Firmware version(s):‐
Upgrade to latest version.
INITIAL SETUP
Sim 26‐01 Job Separator Tray Installation:‐
Yes/No.
Sim 26‐06 Machine Destination.
Sim 26‐35 Set Multi Error Counter
Set to 1 (Multi Count).
Sim 26‐50 Long Size Print Support (up to 1200mm),
D: 0 = Disable, 1 = Enable
.
Sim 55‐03 Process Mixed Size Pages (orientation) when Printing in Duplex:‐
SSW 3‐6,
0 = Disable, 1 = Enable.
Sim 55‐03 Toner Remain Status Display: SSW 22‐5,
0 = Disable, 1 = Enable.
System Settings: Adjust Date/Time (Inc. Daylight Saving setting).
Network Settings – Print Port Settings: Disable WSD.
Set cassette size by adjusting the guides in the cassette.
Paper Size & Type Setting:‐
Paper Size & Type Setting:‐
System Settings – Paper Tray Settings.
PRINT IMAGE POSITION & MAGNIFICATION
Sim 50‐28 SETUP/PRINT ADJ (Lead, Offset or All).
SPF ADJ (Side 1, Side 2 or All).
OC ADJ (MFT, CS1 & CS2).
MANUAL ADJUSTMENTS:‐
Sim 48‐01
Magnification Adjustment (OC & SPF).
Sim 50‐01 Lead/Rear Edge, Loss & Void Adjust.
Sim 50‐05 Printer Lead Edge & Void Adjust.
Sim 50‐10 Image Off Centre Adjustment.
Sim 50‐12 OC & SPF Original Off Centre Adjust.
SHARP
INITIAL SETUP
9
COPY IMAGE QUALITY
Check Image Quality (Copy Mode):‐
If NG, perform the following adjustments as required:‐
Sim 46‐02
Copy Density Adjust. (600dpi).
Sim 46‐09 SPF Copy Density Adjust.
PRINT IMAGE QUALITY
Check Image Quality (Print Mode):‐
Sim 64‐05 PCL Density Test Page.
Sim 64‐06 PS Density Test Page [MX‐PK11].
PERIPHERAL / OPTION CONFIGURATION
FAX OPTION – MX‐FX11
Sim 66‐02 Fax SW Setting (Destination).
Sim 66‐10 Fax Memory Clear (For Extended Memory).
Sim 66‐39 Fax Destination Set.
FINISHER OPTION – MX‐FN26
Sim 26‐65 Finisher Alarm Mode:‐
Limit number of Copies in staple mode
(ON/OFF).
USB WIRELESS ADAPTOR – MX‐EB13
Sim 26‐50 Activate Wireless Set,
E: 0 = Disable, 1 = Enable
.
EXTERNAL ACCOUNTING MODULE – MX‐AMX3
Sim 55‐03 Auto clear function before Copy job execution:‐
SSW 1‐5
0 = Disable, 1 = Enable
.
Sim 55‐03 Continuous print mode (job queuing for OSA):‐
SSW 24‐7
0 = Disable, 1 = Enable
.
MFP DATA BACKUP
Sim 22‐06 Data Simulation Print.
Device Clone & Storage Backup.
Sim 56‐01 Backup EEPROM Data to HDD.
MAINTENANCE
SHARP
10
MAINTENANCE INDICATIONS:
DK
OPC DRUM (Counter) has reached
the specified life.
Replace OPC Drum
Process
Section
(Drum)
VK
BLACK DEVELOPER (Counter) has reached
the specified life.
Replace Developer.
Process
Section
(Developer)
FK1
FUSING ROLLER Print Counter has reached
the specified limit.
Replace Upper Heat
Roller Kit
Fuser
Section
FK2
PRESSURE ROLLER Print Counter has
reached the specified limit.
Replace Lower Heat
Roller Kit
TK
TRANSFER UNIT Counter has reached
the specified limit.
Replace Transfer Roller
Unit
Transfer
Section
TA
Maintenance [All] Counter has reached specified limit
STARTING POWDER:
The following starting powder should be applied to the relevant consumable item during maintenance:‐
Starting Powder
OPC Drum
Transfer Roller Unit
MX‐M266N
MX‐M316N
MX‐M316N
Apply CKOG‐0345DS51
[Yellow Toner] on top of
UKOG‐0312FCZZ [Stearic Acid]
None
CONSUMABLE SCHEDULE:
100K
150K
200K
300K
400K
450K
500K 600K
Process
MX‐312GV Developer
X
X
MX‐312GR Drum
X
X
MX‐312DU Drum frame unit
X
X
X
X
X
X
MX‐312KA Maintenance kit
X
X
X
X
MX‐312TF Toner filter
Fuser
MX‐313UH Upper heat roller kit
X
X
X
X
MX‐312LH Lower heat roller kit
X
X
X
X
X
X
Transfer
MX‐312TX Transfer roller unit
X
X
X
X
SHARP
MAINTENANCE
11
MAINTENANCE SCHEDULE:
100K 150K 200K 300K
PROCESS SECTION:
X
Replace:
Developer
[MX‐312GV]
X
Replace:
Toner Filter
[MX‐312TF]
X
Check/Clean Toner Sensor Head.
X
Replace:
OPC Drum
[MX‐312GR]
X
X
Replace:
Maintenance Kit
[MX‐312KA]:‐
Drum Separation Pawls x 2
Cleaning Blade.
Main Charge Unit.
Cleaning Blade.
Main Charge Unit.
X
X
X
Replace:
Process Frame Unit
[MX‐312DU]:‐
(includes Cleaner Blade, Main Charge Unit & Drum
Separation Pawls)
Check/Clean LSU Dustproof Glass
X
Sim 24‐05
Clear DV_K (Black) Counter.
X
Sim 24‐04
Clear DRUM CTRG K (Black) Counter.
X
Clear MAIN CHARGER K (Black) Counter.
X
Clear DRUM BLADE K (Black) Counter.
X
Clear MAINTENANCE [ALL] Counter.
X
Clear OZONE FILTER Counter.
X
Sim 25‐02* Toner Concentration Auto Adjustment ‐ Select K.
Note* When Sim 25‐02 is executed, the Developer Counter
(Sim 24‐05) is also cleared automatically.
IMAGE QUALITY ADJUSTMENT (After Replacement Described Above):
X
Sim 46‐02
Check/Adjust Copy Exposure Density (B/W).
RSPF:
Check/Clean PF Rollers ‐
replace every 100K.
Check/Clean Torque Limiter ‐
replace every 400K.
Clean all RSPF sensors.
GENERAL
Clean all optics, CCD, and white reference plate.
Replace
Ozone Filter [PFiLZ0041QSZZ].
TRANSFER SECTION:
X
X
Replace:
Transfer Roller Unit
[MX‐312TX].
X
X
Sim 24‐04
Clear TC UNIT Counter.
PAPER FEED & TRANSPORT:
Check/Clean ALL Transport Paper Guides.
Check/Clean ALL Paper Path Sensors.
Check/Clean PF Roller (Cassette & Bypass Tray).
X
Replace:
Cassette PF Roller Kit
[MX‐312RT]
when each Tray
reaches 100K or 1 year of use.
X
Replace:
Bypass Tray Roller Kit
[MX‐312MR]
when the Bypass
Tray reaches 100K or 1 year of use.
Click on the first or last page to see other MX-M266N / MX-M316N / MX-M356N service manuals if exist.