Sharp MX-M266N / MX-M316N / MX-M356N Handy Guide ▷ View online
SHARP
CONSUMABLES
7
CONSUMABLES
MX‐M266N / MX‐M316N
Product Code
Description / Contents
Approx. Life
MX‐315GT
Black Toner Cartridge
(A4 @ 5%)
27.5k
PROCESS UNIT:
MX‐312GV
Black Developer
100k
MX‐312GR
OPC Drum
100k
MX‐315DU
Drum Frame Unit
300k
MX‐312KA
Maintenance Kit:‐
Drum separation pawl x2.
Cleaning blade.
Main charge unit.
Cleaning blade.
Main charge unit.
100k
MX‐312TF
Toner Filter Kit:‐
Toner filter.
100k
FUSING UNIT:
MX‐313UH
Upper Heat Roller Kit:‐
Upper heat roller.
Fusing gear.
Upper heat roller bearing x2.
Upper cleaning pad.
Upper separation pawl x4.
Fusing gear.
Upper heat roller bearing x2.
Upper cleaning pad.
Upper separation pawl x4.
150k
MX‐312LH
Lower Heat Roller Kit:‐
Lower heat roller.
Lower heat roller bearing x2.
Lower separation pawl.
Lower heat roller bearing x2.
Lower separation pawl.
300k
TRANSFER UNIT:
MX‐312TX
Transfer Roller Unit
150k
PERIPHERALS:
MX‐SCX1
Staple Cartridge (for MX‐FN26 Inner Finisher)
5000 staples x3
AR‐SV1
Ink Cartridge (for AR‐SU1 Stamp Unit)
2 cartridges
SERVICE:
MX‐312RT
Feeding Roller Kit (for cassette)
100k
MX‐312MR
Feeding Roller Kit (for bypass tray only)
100k
MX‐312FU
Fusing Unit (230V)
150k
Note:
Consumable life may vary depending on the document density, temperature, humidity and machine
operation.
INITIAL SETUP
SHARP
8
DEVELOPER SETUP & TONER INSTALLATION
Sim 25‐02 Auto Developer Adjustment.
Toner cartridge must be installed before execution.
PRODUCT OPTION ACTIVATION
Activation of Optional Product(s):‐
System Settings – Administrator Mode – Product Key.
FIRMWARE UPGRADE [ALL]
Sim 22‐05 Check Firmware version(s):‐
Upgrade to latest version.
INITIAL SETUP
Sim 26‐01 Job Separator Tray Installation:‐
Yes/No.
Sim 26‐06 Machine Destination.
Sim 26‐35 Set Multi Error Counter
Set to 1 (Multi Count).
Sim 26‐50 Long Size Print Support (up to 1200mm),
D: 0 = Disable, 1 = Enable
.
Sim 55‐03 Process Mixed Size Pages (orientation) when Printing in Duplex:‐
SSW 3‐6,
0 = Disable, 1 = Enable.
Sim 55‐03 Toner Remain Status Display: SSW 22‐5,
0 = Disable, 1 = Enable.
System Settings: Adjust Date/Time (Inc. Daylight Saving setting).
Network Settings – Print Port Settings: Disable WSD.
Set cassette size by adjusting the guides in the cassette.
Paper Size & Type Setting:‐
Paper Size & Type Setting:‐
System Settings – Paper Tray Settings.
PRINT IMAGE POSITION & MAGNIFICATION
Sim 50‐28 SETUP/PRINT ADJ (Lead, Offset or All).
SPF ADJ (Side 1, Side 2 or All).
OC ADJ (MFT, CS1 & CS2).
MANUAL ADJUSTMENTS:‐
Sim 48‐01
Magnification Adjustment (OC & SPF).
Sim 50‐01 Lead/Rear Edge, Loss & Void Adjust.
Sim 50‐05 Printer Lead Edge & Void Adjust.
Sim 50‐10 Image Off Centre Adjustment.
Sim 50‐12 OC & SPF Original Off Centre Adjust.
SHARP
INITIAL SETUP
9
COPY IMAGE QUALITY
Check Image Quality (Copy Mode):‐
If NG, perform the following adjustments as required:‐
Sim 46‐02
Copy Density Adjust. (600dpi).
Sim 46‐09 SPF Copy Density Adjust.
PRINT IMAGE QUALITY
Check Image Quality (Print Mode):‐
Sim 64‐05 PCL Density Test Page.
Sim 64‐06 PS Density Test Page [MX‐PK11].
PERIPHERAL / OPTION CONFIGURATION
FAX OPTION – MX‐FX11
Sim 66‐02 Fax SW Setting (Destination).
Sim 66‐10 Fax Memory Clear (For Extended Memory).
Sim 66‐39 Fax Destination Set.
FINISHER OPTION – MX‐FN26
Sim 26‐65 Finisher Alarm Mode:‐
Limit number of Copies in staple mode
(ON/OFF).
USB WIRELESS ADAPTOR – MX‐EB13
Sim 26‐50 Activate Wireless Set,
E: 0 = Disable, 1 = Enable
.
EXTERNAL ACCOUNTING MODULE – MX‐AMX3
Sim 55‐03 Auto clear function before Copy job execution:‐
SSW 1‐5
0 = Disable, 1 = Enable
.
Sim 55‐03 Continuous print mode (job queuing for OSA):‐
SSW 24‐7
0 = Disable, 1 = Enable
.
MFP DATA BACKUP
Sim 22‐06 Data Simulation Print.
Device Clone & Storage Backup.
Sim 56‐01 Backup EEPROM Data to HDD.
MAINTENANCE
SHARP
10
MAINTENANCE INDICATIONS:
DK
OPC DRUM (Counter) has reached
the specified life.
Replace OPC Drum
Process
Section
(Drum)
VK
BLACK DEVELOPER (Counter) has reached
the specified life.
Replace Developer.
Process
Section
(Developer)
FK1
FUSING ROLLER Print Counter has reached
the specified limit.
Replace Upper Heat
Roller Kit
Fuser
Section
FK2
PRESSURE ROLLER Print Counter has
reached the specified limit.
Replace Lower Heat
Roller Kit
TK
TRANSFER UNIT Counter has reached
the specified limit.
Replace Transfer Roller
Unit
Transfer
Section
TA
Maintenance [All] Counter has reached specified limit
STARTING POWDER:
The following starting powder should be applied to the relevant consumable item during maintenance:‐
Starting Powder
OPC Drum
Transfer Roller Unit
MX‐M266N
MX‐M316N
MX‐M316N
Apply CKOG‐0345DS51
[Yellow Toner] on top of
UKOG‐0312FCZZ [Stearic Acid]
None
CONSUMABLE SCHEDULE:
100K
150K
200K
300K
400K
450K
500K 600K
Process
MX‐312GV Developer
X
X
MX‐312GR Drum
X
X
MX‐312DU Drum frame unit
X
X
X
X
X
X
MX‐312KA Maintenance kit
X
X
X
X
MX‐312TF Toner filter
Fuser
MX‐313UH Upper heat roller kit
X
X
X
X
MX‐312LH Lower heat roller kit
X
X
X
X
X
X
Transfer
MX‐312TX Transfer roller unit
X
X
X
X
Click on the first or last page to see other MX-M266N / MX-M316N / MX-M356N service manuals if exist.