Sharp MX-M266N / MX-M316N / MX-M356N (serv.man6) Service Manual ▷ View online
MX-M316N NOTE FOR SERVICING - i
MX-M316N
Service Manual
NOTE FOR SERVICING
* About a main unit illustration, it may differ from a target model.
1.
Precautions for servicing
* When servicing, disconnect the power plug, the printer cable, the
network cable, and the telephone line from the machine, except
when performing the communication test, etc.
when performing the communication test, etc.
It may cause an injury or an electric shock.
* There is a high temperature area inside the machine. Use
extreme care when servicing.
It may cause a burn.
* There is a high voltage section inside the machine which may
cause an electric shock. Be careful when servicing.
* Do not disassemble the laser unit. Do not insert a reflective
material such as a screwdriver in the laser beam path.
It may damage eyes by reflection of laser beams.
* When servicing with the machine operating, be careful not to
squeeze you hands by the chain, the belt, the gear, and other
driving sections.
driving sections.
* Do not leave the machine with the cabinet disassembled.
Do not allow any person other than a serviceman to touch inside
the machine. It may cause an electric shock, a burn, or an injury.
the machine. It may cause an electric shock, a burn, or an injury.
* When servicing, do not breathe toner, developer, and ink exces-
sively. Do not get them in the eyes.
If toner, developer, or ink enters your eyes, wash it away with
water immediately, and consult a doctor if necessary.
water immediately, and consult a doctor if necessary.
* The machine has got sharp edges inside. Be careful not to dam-
age fingers when servicing.
* Do not throw toner or a toner cartridge in a fire. Otherwise, toner
may ignite and burn you.
* When replacing a lithium battery on a PWB, only use the speci-
fied replacement battery.
If a battery of different specification is used, it may cause a
machine malfunction or breakdown.
machine malfunction or breakdown.
* When carrying a unit with PWB or electronic parts installed to it,
be sure to put it in an anti-static-electricity bag.
It may otherwise cause a machine breakdown or malfunction.
2.
Warning for servicing
* Be sure to connect the power cord only to a power outlet that
meets the specified voltage and current requirements.
Avoid complex wiring, which may lead to a fire or an electric
shock.
shock.
It may cause a fire or an electric shock.
* If there is any abnormality such as a smoke or an abnormal
smell, interrupt the job and disconnect the power plug.
It may cause a fire or an electric shock.
* Be sure to connect the grounding wire. If an electric leakage
occurs without grounding, a fire or an electric shock may result.
To protect the machine and the power unit from lightening,
grounding must be made.
grounding must be made.
* When connecting the grounding wire, never connect it to the fol-
lowing points.
- Gas tube
- Lightning conductor
- A water pipe or a water faucet, which is not recognized as a
grounding object by the authorities.
- Grounding wire for telephone line
It may cause an explosion, a fire or an electric shock.
* Do not damage, break, or stress the power cord.
Do not put heavy objects on the power cable. Do not stress, forc-
ibly bend, or pull the power cord.
ibly bend, or pull the power cord.
It may cause a fire or an electric shock.
* Keep the power cable away from a heat source.
Do not insert the power plug with dust on it into a power outlet.
It may cause a fire or an electric shock.
* Do not place liquids or foreign metallic objects inside the
machine.
It may cause a fire or an electric shock.
* Do not touch the power cord, insert the phone jack, operate the
machine, or perform service on the machine with wet or oily
hands.
hands.
It may cause an electric shock.
3.
Note for installing site
Do not install the machine at the following sites.
* Place of high temperature, high humidity, low temperature,
low humidity, place under an extreme change in temperature
and humidity.
and humidity.
Paper may get damp and form condensation inside the machine,
causing paper jam or copy dirt.
causing paper jam or copy dirt.
For operating and storing conditions, refer to the specifications
described later.
described later.
* Place of extreme vibrations
It may cause a breakdown.
* Poorly ventilated place
An electrostatic type copier will produce ozone.
The quantity of ozone produced is designed to a low level so as
not to affect human bodies. However, continuous use of such a
machine may produce an ozone smell. Install the machine in a
well ventilated place.
not to affect human bodies. However, continuous use of such a
machine may produce an ozone smell. Install the machine in a
well ventilated place.
CAUTION
DOUBLE POLE/NEUTRAL FUSING
(200V series only)
MX-M316N NOTE FOR SERVICING - ii
* Place of direct sunlight.
Plastic parts and ink may be deformed, discolored, or may
undergo qualitative change.
undergo qualitative change.
It may cause a breakdown or output quality problems.
* Place which is full of organic gases such as ammonium
The organic photo-conductor (OPC) drum used in the machine
may undergo qualitative change due to organic gases such as
ammonium.
may undergo qualitative change due to organic gases such as
ammonium.
Installation of this machine near a diazo-type copier and blue
print machine may result in poor quality output.
print machine may result in poor quality output.
* Place of much dust
When dust or contaminants enters the machine, it may cause a
breakdown or poor quality output.
breakdown or poor quality output.
* Place near a wall
The machine will require ventilation.
If ventilation is not proper, poor output or machine failure may
result.
result.
* Unstable or irregular surface
If the machine is dropped or tips over, it may cause injury or
machine malfunction.
machine malfunction.
Use an optional desk or an exclusive-use desk.
When using the optional desk, be sure to fix the adjuster and lock
the casters.
the casters.
4.
Note for handling PWB and electronic
parts
parts
When handling the PWB and the electronic parts, be sure to
observe the following precautions in order to prevent against dam-
age by static electricity.
observe the following precautions in order to prevent against dam-
age by static electricity.
* When in transit or storing, put the parts in an anti-static bag or an
anti-static case and do not touch them with bare hands.
* When and after removing the parts from an anti-static bag (case),
use an earth band as shown below:
* Put an earth band to your arm, and connect it to the machine.
* When repairing or replacing an electronic part, perform the
procedure on an anti-static mat.
11-13/16"
(30cm)
(30cm)
11-13/16"
(30cm)
(30cm)
17-23/32"
(45cm)
(45cm)
MX-M316N NOTE FOR SERVICING - iii
5.
Note for repairing/replacing the LSU
When repairing or replacing, be sure to observe the following
items.
items.
* When repairing or replacing the LSU, be sure to disconnect the
power plug from the power outlet.
* When repairing or replacing the LSU, follow the procedures
described in this Service Manual.
* When checking the operations after repairing the LSU, keep all
the parts including the cover installed and perform the operation
check.
check.
* Do not modify the LSU.
* When visually checking the inside of the machine for the opera-
tion check, be careful not to allow laser beams to enter the eyes.
If the above precaution is neglected or the LSU is modified, ones
safety may be at risk.
safety may be at risk.
6.
Note for handling the drum unit, the
developing unit
developing unit
When handling the OPC drum unit, and the developing unit, strictly
observe the following items.
observe the following items.
If these items are neglected, a trouble may be generated in the
copy and print image quality.
copy and print image quality.
Drum unit
* Avoid working at a place with strong lights.
* Do not expose the OPC drum to lights including interior lights for
a long time.
* When the OPC drum is removed from the machine, cover it with
light blocking material. (When using paper, use about 10 sheets
of paper to cover it.)
of paper to cover it.)
* Be careful not to attach fingerprints, oil, grease, or other foreign
material on the OPC drum surface.
Developing unit
* Be careful not to leave fingerprints, oil, grease, or other foreign
material on the developing unit.
Fusing unit
* Be careful not to "leave" fingerprints, oil, grease, or other foreign
material on the fusing roller.
If these items are neglected, a trouble may be generated in the
copy and print image quality.
copy and print image quality.
7.
Screw tightening torque
The screws used in this machine are largely classified into three
types.
types.
These types are classified according to the shape of the screw
grooves and use positions.
grooves and use positions.
The table below shows the types of the screws and the tightening
torques depending on the use position.
torques depending on the use position.
When tightening the screws for repair or maintenance, refer to the
table.
table.
However, for the other conditions of tightening screws than speci-
fied on this table, or under special circumstances, the details are
described on the separate page. Refer to the descriptions on such
an exception.
fied on this table, or under special circumstances, the details are
described on the separate page. Refer to the descriptions on such
an exception.
CAUTION: Especially for the screw fixing positions where there is
an electrode or a current flows, use enough care to
tighten securely to avoid loosening.
tighten securely to avoid loosening.
Screw kinds and tightening torques
Normal screws, set screws (including step screws)
Tapping screws (for iron)
Tapping screw (for plastic)
8.
Relation between model names and
names in the manual
names in the manual
Screw
diameter
Material to be
fixed
Tightening
torque
(N
m)
Tightening
torque
(kgf
cm)
Tightening
torque
(lbft)
M2.6
Steel plate
0.8 - 1.0
8 - 10
0.6 - 0.7
M3
Steel plate
1.0 - 1.2
10 - 12
0.7 - 0.9
M4
Steel plate
1.6 - 1.8
16 - 18
1.2 - 1.3
Screw
diameter
Material to be
fixed
Tightening
torque
(N
m)
Tightening
torque
(kgf
cm)
Tightening
torque
(lbft)
M3
Steel plate
(Plate thickness
0.8mm or above)
1.0 - 1.2
10 - 12
0.7 - 0.9
M4
Steel plate
(Plate thickness
0.8mm or above)
1.6 - 1.8
16 - 18
1.2 - 1.3
M3
Steel plate
(Plate thickness
less than 0.8mm)
0.6 - 0.8
6 - 8
0.4 - 0.6
M4
Steel plate
(Plate thickness
less than 0.8mm)
1.2 - 1.4
12 - 14
0.9 - 1.0
Screw
diameter
Material to be
fixed
Tightening
torque
(N
m)
Tightening
torque
(kgf
cm)
Tightening
torque
(lbft)
M3
Plastic resin
0.6 - 0.8
6 - 8
0.4 - 0.6
M4
Plastic resin
1.0 - 1.2
10 - 12
0.7 - 0.9
Model name
Name in the manual
MX-M266N/MX-M265N/MX-M265U
26cpm machine
MX-M316N/MX-M315N/MX-M315U
31cpm machine
MX-M356N/MX-M356U
35cpm machine
1
1
: ‘15/Aug.
MX-M316N PRODUCT OUTLINE 1 – 1
MX-M316N
Service Manual
[1] PRODUCT OUTLINE
1. System configuration
A. N model
MX-M316N/M266N/M315N/M356N
DIGITAL MULTIFUNCTIONAL
SYSTEM
SYSTEM
MX-M265N/M265NE
DIGITAL MULTIFUNCTIONAL
SYSTEM
SYSTEM
MX-TR18
JOB SEPARATOR
MX-FN26
FINISHER
MX-CS12
500 SHEET PAPER TRAY
MX-CS13
500 SHEET PAPER TRAY
MX-TR17
EXIT TRAY UNIT
MX-CS12
500 SHEET PAPER TRAY
AR-DS20
LOW STAND
AR-DS19
HIGH STAND
MX-HD14
HARD DISK EXPANSION KIT
MX-PK11
PS3 EXPANSION KIT
MX-PF10
BARCODE FONT KIT
MX-FX11
FACSIMILE EXPANSION
KIT
KIT
AR-SU1
STAMP UNIT
MX-FR48U
DATA SECURITY KIT
MX-FWX1
INTERNET FAX EXPANSION
KIT
KIT
MX-USX1
SHARPDESK 1 LICENSE
KIT
KIT
MX-USX5
SHARPDESK 5 LICENSE
KIT
KIT
MX-US10
SHARPDESK 10 LICENSE
KIT
KIT
MX-US50
SHARPDESK 50 LICENSE
KIT
KIT
MX-USA0
SHARPDESK 100 LICENSE
KIT
KIT
MX-AMX1
APPLICATION
INTEGRATION MODULE
INTEGRATION MODULE
MX-AMX2
APPLICATION
COMMUNICATION MODULE
COMMUNICATION MODULE
MX-AMX3
EXTERNAL ACCOUNT
MODULE
MODULE
MX-EB13
USB WIRELESS LAN
ADAPTER
ADAPTER
MX-M316N/M266N/M315N
/M265N
/M265N
MX-M316N/M266N/M315N
/M265N
/M265N
MX-HD15
HARD DISK EXPANSION KIT
MX-M356N
MX-FR50U
DATA SECURITY KIT
MX-M356N
MX-M316N
A/M266N A/M356N A
MX-M315NE
MX-M316N/M266N/M315N/
M265N/MX-M316N
M265N/MX-M316N
A/M266N A/
M356N A/M315NE/M265NE
MX-M316N/M266N/M315N/
M265N/MX-M316N
M265N/MX-M316N
A/M266N A/
M356N A
MX-
M315NE/M265NE
1
: ‘15/Aug.
1
2
: ‘16/Jun.
2