DOWNLOAD Sharp MX-M266N / MX-M316N / MX-M356N (serv.man4) Service Manual ↓ Size: 26.56 MB | Pages: 76 in PDF or view online for FREE

Model
MX-M266N MX-M316N MX-M356N (serv.man4)
Pages
76
Size
26.56 MB
Type
PDF
Document
Service Manual
Brand
Device
Copying Equipment / NOTE Installation Manual for models with the V suffix.
File
mx-m266n-mx-m316n-mx-m356n-sm4.pdf
Date

Sharp MX-M266N / MX-M316N / MX-M356N (serv.man4) Service Manual ▷ View online

3. Symbols used for kinds of parts
4. Symbols used for additional 
descriptions
Cleaning 
(Vacuum)
Indicates that cleaning is 
performed with a 
vacuum cleaner.
Cleaning 
(Brush)
Indicates that cleaning is 
performed with a brush.
Oil
Indicates that oil is 
applied to lubricate.
Apply powder.
Indicates that setting 
power is applied to the 
photoconductor drum, 
the transfer belt, etc.
Replace
Indicates that a part is 
replaced.
Check
Indicates that a check 
(replacement, 
adjustment, cleaning) is 
performed.
Cut
Indicates that cutting is 
performed.
Loosen
Indicates that a screw is 
loosened.
Connect
Indicates that a 
connector is connected.
Disconnect
Indicates that a 
connector is 
disconnected.
Remove a 
harness.
Indicates that a harness 
is unsecured.
Attach a harness.
Indicates that a harness 
is secured.
Remove a clamp.
Attach a clamp.
Release a hook.
Indicates that a hook is 
released.
Fix a hook. 
Indicates that a hook is 
fixed.
Disengage the 
pawl.
Symbol
Meaning (Work content)
Engage the pawl.
Screw lock
Indicates that a screw is 
secured with adhesive.
Unlock
Turn OFF the 
power.
Disconnect the 
power plug.
Symbol
Meaning (Kinds of parts)
Maintenance 
part
Indicates a part which is 
replaced in a maintenance 
procedure.
Consumable 
part
Indicates a consumable 
part such as a 
photoconductor, 
developer, a transfer belt, 
etc.
Waste part
Indicates a waste part 
which is consumed but 
excluded from the above 
consumable parts. (A 
roller, a seal, etc.)
Unit part
Indicates a part which is 
designated as a unit.
Included part
Indicates a part which is 
included in the package
Symbol
Meaning
View from the 
top
Indicates from which 
angle the drawing is 
viewed.
View from the 
bottom
View from the 
front
View from the 
back
Symbol
Meaning (Work content)
MX-M356NV  Transit, Installation (using) environment, Note   - i
MX-M356NV
Service Manual
 
Transit, Installation (using) environment, Note
* About a main unit illustration, it may differ from a target model.
1. Installing (use) conditions
Before installing the machine, check that the following installing
(use) conditions are satisfied.
If the installing (use) conditions are not satisfied, the machine may
not display full performances, resulting in troubles. It may also
cause safety problems. Therefore, be sure to arrange the installing
(use) conditions before setting up the machine.
A. Transportation space
For installation of a large size machine, be sure to check that the
door size is wide enough before bringing in.
B. Installing space
The following space must be provided around the machine in order
to assure machine performances and proper operations.
If any option is installed, provide the additional space for installing
it.
Adequate space must be provide behind the machine for proper
ventilation heat and dust. If not, the machine cannot exhibit func-
tions against heat and dust, causing some troubles.
C. Power source (Capacity, voltage, frequency, 
safety, plug)
If the power specifications are not satisfied, the machine cannot
exhibit full performances and may cause safety trouble.
Strictly observe the following specifications.
(1)
Power capacity
Check that the following power capacity is satisfied. If not, addition-
ally provide a power source.
Current capacity
Japan: 20A or more
EX 100V: 15A or more
EX 200V: 10A or more
NOTE: Check the shape of the power plug of the machine, and
insert it into a power outlet of the acceptable shape.
(2)
Power voltage
Measure the voltage during copying to check that the voltage is in
the range of the specified voltage 
If the voltage is outside the specified range, please have a certified
electrician upgrade the outlet.
(An electrical work is required.)
Use of a step-up transformer is also available. In this case, the
capacity must be great enough for the max. power consumption of
the machine.
(3)
Power frequency, waveform
The frequency must be within the range of the specified frequency
(4)
Safety
Be sure to properly ground the machine.
Grounding (earth connection) must be performed before inserting
the power plug into the power outlet.
When disconnecting the earth connection, be sure to disconnect
the power plug from the power outlet in advance.
(5)
Power plug
Check the shape of the power plug of the machine, and insert it into
a power outlet of the acceptable shape.
Power plug stated in power capacity.
D. Floor strength and level
This machine is considerably heavy and becomes heavier with an
option installed.
The floor must be strong enough to safely support the weight of the
machine as well as any installed options.
If the unit is not horizontally installed, the toner density control is
not performed normally, degrading the copy quality.
If not, color shift or image distortion may occur.
To assure proper Image quality, make sure the machine is setting
level.
E. Direct rays of the sun, dust, temperature, 
humidity, gasses, chemicals, vibration
(1)
Temperature and humidity (Environmental 
conditions)
This machine is designed to perform properly under the specified
temperature and humidity. If the temperature and humidity exceeds
the specified range, the machine may not operate properly and or
cause equipment failure.
Especially when the humidity is too high, paper absorbs humidity to
cause a paper jam or dirty copy.
Do not install the machine near a heater, a cooler, or a humidifier.
Condensation may form inside the machine causing multiple trou-
bles. Use enough care for ventilation.
Operational environment
Temperature: 10 to 35
Humidity: 20 to 85% RH
Atmospheric pressure: 590 to 1013hPa (altitude: 0 to 2000 m)
(2)
Contaminates
If dust enters the machine, it may cause dirty copy and a paper
jam, resulting in a shortened lifetime.
(3)
Direct sunlight
If the machine is installed under the rays of the sun, the exterior of
the machine may be discolored and abnormal copies may be pro-
duced.
(4)
Gases and chemicals
Do not install the machine at a place where there are gases and
chemicals. Especially be careful to avoid installation near a diazo-
type copier, which produces ammonium gas.
Copy quality may be adversely affected and a trouble may be
caused.
(5)
Vibration
Avoid installation near a machine which produces vibrations.
If vibrations are applied to the copier machine, copy images may be
deflected and a trouble may be caused.
No.
Content
1
Transportation space
2
Installing space
3
Power source (Capacity, fluctuation, safety)
4
Floor strength
5
Direct rays of the sun, dust, temperature, humidity, gases, 
chemicals
11-13/16" 
(30cm)
11-13/16" 
(30cm)
17-23/32" 
(45cm)
MX-M356NV  Transit, Installation (using) environment, Note   - ii
F. Note for handling PWB and electronic parts
When handling the PWB and the electronic parts, be sure to
observe the following precautions in order to prevent against dam-
age by static electricity.
? When in transit or storing, put the parts in an anti-static bag or an
anti-static case and do not touch them with bare hands.
? When and after removing the parts from an anti-static bag
(case), use an earth band as shown below:
? Put an earth band to your arm, and connect it to the machine.
? When repairing or replacing an electronic part, perform the
procedure on an anti-static mat.
G. Note for proper drum, developing and fusing 
unit handling
When handling the OPC drum and developing units, observe the
following items.
Drum unit
? To prevent  damage to the OPC drum, avoid working on the
drum unit in high intensity light areas.
? When the OPC drum is removed from the machine, cover it with
light blocking material. (When using paper, use about 10 sheets
of paper to cover it.)
? Be careful not to attach fingerprints, oil, grease, or other foreign
material on the OPC drum surface.
Developing unit
? Be careful not to "leave” fingerprints, oil, grease, or other foreign
material on the developing unit.
Fusing unit
? Be careful not to "leave” fingerprints, oil, grease, or other foreign
material on the fusing roller.
If these items are neglected, a trouble may be generated in the
copy and print image quality.
2. Transit and delivery
A. Implements, facility, and manpower
It is recommendable to use a forklift for bringing in the machine for
safety.
If no forklift is available, man-power of two persons is required. The
machine is considerably heavy, and requires safety precautions for
delivery and installation.
Transit of the machine must be made in packed condition to the
installing place.
Use care not to exert vibrations or shocks to the machine when in
transit.
B. Delivery
Remove the packing materials prior to installation in the office envi-
ronment.
No.
Content
Method
1
Implements, facility, 
and man power
Use a forklift. (If no forklift is available, 
manpower of two persons is required.) 
2
Delivery
Transit must be made in packed condition.
MX-M356NV  CONFIGURATION  1 – 1
MX-M356NV
Service Manual
 
[1] CONFIGURATION
1. System diagram
A. NV model
MX-M266NV/M316NV/
M315NV/M315V/M356NV
DIGITAL MULTIFUNCTIONAL
SYSTEM
MX-M265NV/M265V
DIGITAL MULTIFUNCTIONAL
SYSTEM
MX-TR18 N
JOB SEPARATOR
MX-FN26 N
FINISHER
MX-CS12 N
500 SHEET PAPER TRAY
MX-CS13 N
500 SHEET PAPER TRAY
MX-TR17 N
EXIT TRAY UNIT
MX-CS12 N
500 SHEET PAPER TRAY
AR-DS20
LOW STAND
AR-DS19
HIGH STAND
MX-HD14E N
HARD DISK EXPANSION KIT
MX-PK11
PS3 EXPANSION KIT
MX-PF10
BARCODE FONT KIT
MX-FX11
FACSIMILE EXPANSION
KIT
AR-SU1
STAMP UNIT
MX-FWX1
INTERNET FAX EXPANSION
KIT 
MX-USX1
SHARPDESK 1 LICENSE
KIT
MX-USX5
SHARPDESK 5 LICENSE
KIT
MX-US10
SHARPDESK 10 LICENSE
KIT
MX-US50
SHARPDESK 50 LICENSE
KIT
MX-USA0
SHARPDESK 100 LICENSE
KIT
MX-AMX1
APPLICATION
INTEGRATION MODULE
MX-AMX2
APPLICATION
COMMUNICATION MODULE
MX-AMX3
EXTERNAL ACCOUNT
MODULE 
MX-EB13
USB WIRELESS LAN 
ADAPTER
MX-HD15 N
HARD DISK EXPANSION KIT
MX-FR50U
DATA SECURITY KIT
Page of 76
Display

Sharp MX-M266N / MX-M316N / MX-M356N (serv.man4) Service Manual ▷ Download

  • DOWNLOAD Sharp MX-M266N / MX-M316N / MX-M356N (serv.man4) Service Manual ↓ Size: 26.56 MB | Pages: 76 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sharp MX-M266N / MX-M316N / MX-M356N (serv.man4) in PDF for free, which will help you to disassemble, recover, fix and repair Sharp MX-M266N / MX-M316N / MX-M356N (serv.man4) Copying Equipment. Information contained in Sharp MX-M266N / MX-M316N / MX-M356N (serv.man4) Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.