Sharp MX-M1055 / MX-M1205 Service Manual ▷ View online
MX-M1205 NOTE FOR SERVICING 0 - ii
3)
Poorly ventilated place
An electro-static type copier will produce ozone inside it.
The quantity of ozone produced is designed to a low level so
as not to affect human bodies. However, continuous use of
such a machine may produce a smell of ozone. Install the
machine in a well ventilated place, and ventilate occasionally.
as not to affect human bodies. However, continuous use of
such a machine may produce a smell of ozone. Install the
machine in a well ventilated place, and ventilate occasionally.
When using special paper such as glossy paper, unique smell
or gas may be generated. Provide an additional duct to
exhaust the smell and gas from the exhaust section of the
machine as needed. (There is no setting for the exclusive-use
duct.)
or gas may be generated. Provide an additional duct to
exhaust the smell and gas from the exhaust section of the
machine as needed. (There is no setting for the exclusive-use
duct.)
4)
Place of direct sunlight.
Plastic parts and ink may be deformed, discolored, or may
undergo qualitative change.
undergo qualitative change.
It may cause a breakdown or copy dirt.
5)
Place which is full of organic gases such as ammonium
The organic photoconductor (OPC) drum used in the machine
may undergo qualitative change due to organic gases such as
ammonium.
may undergo qualitative change due to organic gases such as
ammonium.
Installation of this machine near a diazo-type copier may result
in dirt copy.
in dirt copy.
6)
Place of much dust
When dusts enter the machine, it may cause a breakdown or
copy dirt.
copy dirt.
7)
Place near a wall
Some machine require intake and exhaust of air.
If intake and exhaust of air are not properly performed, copy
dirt or a breakdown may be resulted.
dirt or a breakdown may be resulted.
When installing the machine, make sure that the sides and
back of the machine are at least 11-13/16" (30 cm) away from
any walls.
back of the machine are at least 11-13/16" (30 cm) away from
any walls.
There is a portion currently expressed with the illustration of a con-
ventional model in this manual.
ventional model in this manual.
11-13/16"
(30 cm)
(30 cm)
11-13/16"
(30 cm)
(30 cm)
11-13/16"
(30 cm)
MX-M1205 PRODUCT OUTLINE 1 – 1
MX-M1205
Service Manual
[1] PRODUCT OUTLINE
1. System diagram
MX-AMX1
APPLIC ATION
INTEGR ATION MODULE
INTEGR ATION MODULE
MX-AMX2
APPLIC ATION
COMMUNIC ATION MODULE
COMMUNIC ATION MODULE
MX-AMX3
EXTERNAL ACCOUNT
MODULE
MODULE
MX-PUX1
XPS EX PANSION KIT
MX-PE11
Fiery print Controller
MX-PX11
Interface Kit
MX-PF10
BARCODE FONT KIT
AR-SU1
S TAMP UNIT
MX-EB11
ENHANCED COMPRESSION
KIT
KIT
AR-SV1
S TAMP CA R TRIDGE
MX-AM10
WEB B R OWSING EX PANSION
KIT
KIT
MX-KB18
KEYBOAD
MX-EB15
MIR R ORING KIT
MX-FR53U
DATA SECURITY KIT
MX-SCX1
S TAPLE CA R TRIDGE
(For 50 sheets binding)
MX-SCX2
S TAPLE CA R TRIDGE
(For 100 sheets binding)
(For 100 sheets binding)
MX-RB18
CURL CORRECTION
UNIT
UNIT
MX-ST10
HIGH CAPACITY
STACKER
STACKER
MX-CA10
PAPER CART
MX-CA10
PAPER CART
MX-ST10
HIGH CAPACITY
STACKER
STACKER
MX-FD10
FOLDING UNIT
MX-LC13 N
LARGE CA PACITY
TR AYS
TR AYS
MX-MFX1
MULTI BYPASS TRAY
MX-MF11
MULTI BYPASS TRAY
MX-RB16
PAPER PASS
MODULE
MODULE
MX-RB17
*1
CONNECTION
MODULE
MODULE
*1: Option for 2nd MX-LC13
MX-LC12
LARGE CAPACITY
TRAY
TRAY
MX-SL10 N
STATUS INDICATOR
MX-RB13
RELAY UNIT
MX-CF11
INSERTER
MX-M1055/M1205
DIGITAL MULTIFUNCTIONAL SYSTEM
MX-PN13
A/B/C/D
A/B/C/D
PUNCH
MODULE
MODULE
MX-FN22
SADDLE STTICH
FINISHER
FINISHER
MX-FN21
FINISHER
MX-TM10
TRIMMING
MODULE
MODULE
MX-M1205 PRODUCT OUTLINE 1 – 2
2. Option list
*1: Only North American standard
*2: North American and Europe standard (Sharp OSA Utility CD-ROM No)
Model
name
Name
MX-M1055/
M1205
Remarks
Paper feed system
MX-MFX1
MULTI BYPASS TRAY
For Main unit
MX-MF11
MULTI BYPASS TRAY
For large capacity trays
MX-LC13 N
LARGE CAPACITY TRAYS
A3
MX-RB16
PAPER PASS MODULE
For large capacity trays
MX-RB17
CONNECTION MODULE
For large capacity trays
MX-LC12
LARGE CAPACITY TRAYS
A4
Paper exit system
MX-RB18
CURL CORRECTION UNIT
MX-RB13
RELAY UNIT
For direct connection between MX-CF11 and MX-FN21/
22.
22.
MX-FN21
FINISHER
100 sheets binding
MX-FN22
SADDLE STITCH FINISHER
100 sheets binding/saddle 20 sheets binding
MX-TM10
TRIMMING MODULE
MX-CF11
INSERTER
MX-ST10
HIGH CAPACITY STACKER
MX-CA10
PAPER CART
MX-FD10
FOLDING UNIT
MX-PN13A
PUNCH MODULE
For 100 sheets binding
MX-PN13B
PUNCH MODULE
For 100 sheets binding
MX-PN13C
PUNCH MODULE
For 100 sheets binding
MX-PN13D
PUNCH MODULE
For 100 sheets binding
Printer expansion
MX-PUX1
XPS EXPANSION KIT
MX-PF10
BARCODE FONT KIT
EFI
MX-PE11
Fiery print Controller
OPT (Local)
MX-PX11
Interface Kit
OPT
Image send expansion
AR-SU1
STAMP UNIT
MX-EB11
ENHANCED COMPRESSION KIT
Authentication/
Security
Security
MX-FR53U
DATA SECURITY KIT
MX-EB15
MIRRORING KIT
Application/Solution
MX-AMX1
APPLICATION INTEGRATION MODULE
MX-AMX2
APPLICATION COMMUNICATION MODULE
OPT*
2
MX-AMX3
EXTERNAL ACCOUNT MODULE
OPT*
2
MX-KB18
KEYBOARD
OPT*
1
MX-AM10
WEB BROWSING EXPANSION KIT
OPT*
1
Other
MX-SL10 N
STATUS INDICATOR
Service
MX-SCX2
STAPLE CART
For staple
(100 sheets saddle finisher / 100 sheets finisher)
(100 sheets saddle finisher / 100 sheets finisher)
MX-SCX1
STAPLE CART
For saddle staple (100 sheets saddle finisher)
AR-SV1
STAMP CARTRIDGE
MX-M1205 SPECIFICATIONS 2 – 1
MX-M1205
Service Manual
[2] SPECIFICATIONS
1. Basic specifications
A. Engine specification
B. Engine speed (ppm)
<Tray 1 - 4, LCC, LCT>
For heavy paper, the speed is same as that for plain paper, except
for the items below.
For heavy paper, the speed is same as that for plain paper, except
for the items below.
<Manual paper feed, LCT manual paper feed>
For heavy paper, the speed is same as that for plain paper, except
for the items below.
For heavy paper, the speed is same as that for plain paper, except
for the items below.
* For the items below, same as for the plain paper.
Thin paper/Recycled paper (Standard paper)/Color paper (Stan-
dard paper)
dard paper)
C. Printable range
The printable area must be as large as the A3 / 11 X 17 page
dimension+ flap for fastening + cropped mark (310 X 462.5mm) by
PCL / PS driver.
dimension+ flap for fastening + cropped mark (310 X 462.5mm) by
PCL / PS driver.
D. Engine resolution
*2: Dither process is executed by an 8bit input.
E. Scanner section
(1)
Resolution/Gradation
(2)
Document table
Photoconductor type
OPC (Drum diameter:
120mm)
Recording system
Electronic photo system (Laser)
Developing system
Dry type 2-component magnetic brush
development
development
Charging system
Wire charging system
Transfer system
Transfer belt system
Cleaning system
Counter blade
Fusing system
Heat roller
Toner supply system
Toner continuous run
Waste toner process
Without toner recycle system/
Toner collection container system
Toner collection container system
Paper
105cpm
machine
120cpm
machine
469mm x 318mm, Extra
48
49
12" x 18" (A3W)
49
51
SRA3
49
52
440mm x 312mm
50
53
A3, 11" x 17", 8K
52
54
B4, 8.5" x 14", 8.5" x 13",
8.5" x 13.4", 8.5" x 13.5"
8.5" x 13.4", 8.5" x 13.5"
58
66
A4R, B5R, 8.5" x 11"R,
7.25" x 10.5"R, 16KR
7.25" x 10.5"R, 16KR
67
76
318mm x 234mm
78
88
9" x 12" (A4W)
80
89
SRA4 81
90
312mm x 220mm
83
92
A4, B5, 8.5" x 11", 16K
105
120
A5R, 5.5" x 8.5"R
105
120
Heavy paper (A4, B5, 8.5" x 11", 16K)
72
81
Heavy paper (A5R, 5.5" x 8.5"R)
72
81
Heavy paper (318mm x 234mm)
72
81
Heavy paper (9" x 12" (A4W))
72
81
Heavy paper (SRA4)
72
81
Heavy paper (312mm x 220mm)
72
81
OHP (11" X 17", A4) (Face-up)
72
81
OHP (A4R, 11" X 17"R) (Face-up)
67
76
OHP (Ohter) (Face-up)
48
55
Paper
105cpm
machine
120cpm
machine
469mm x 318mm, Extra
48
49
12" x 18" (A3W)
49
51
SRA3
49
52
440mm x 312mm
50
53
A3, 11" x 17", 8K
52
54
B4, 8.5" x 14", 8.5" x 13",
8.5" x 13.4", 8.5" x 13.5"
8.5" x 13.4", 8.5" x 13.5"
58
66
A4R, B5R, 8.5" x 11"R,
7.25" x 10.5"R, 16KR
7.25" x 10.5"R, 16KR
67
76
318mm x 234mm
78
88
9" x 12" (A4W)
80
89
SRA4
81
90
312mm x 220mm
83
92
A4, B5, 8.5" x 11", 16K
105
120
A5R, 5.5" x 8.5"R
105
120
Heavy paper (A4, B5, 8.5" x 11", 16K)
72
81
Heavy paper (A5R, 5.5" x 8.5"R)
72
81
Heavy paper (318mm x 234mm)
72
81
Heavy paper (SRA4/A4W)
72
81
Heavy paper (312mm x 220mm)
72
81
Heavy paper (Postcard (High))
(Face-up)
(Face-up)
54
64
OHP (11" x 17", A4) (Face-up)
72
81
OHP (A4R, 11" x 17"R) (Face-up)
67
76
OHP (Other) (Face-up)
48
55
Max. print size
310 X 462.5mm
Void area
Lead edge: 2-5mm
Rear edge: 2-5mm
LR total: 8mm or less
FR total: 4 ± 2mm
(unprintable if 310mm or more)
Rear edge: 2-5mm
LR total: 8mm or less
FR total: 4 ± 2mm
(unprintable if 310mm or more)
Resolution
Copy
Writing
1200dpi x 1200dpi,
600dpi x 600dpi
1200dpi x 1200dpi,
600dpi x 600dpi
Print
Writing
600 x 600dpi (Default)
1,200 x 1,200dpi
600 x 600dpi (Default)
1,200 x 1,200dpi
Gradation
(256 levels
(256 levels
*2
)
Copy
Writing
1200 x 1200dpi
1bit
600dpi x 600dpi
4bit
Print
Writing
PCL
600 x 600dpi
1bit, 4bit
1,200 x 1,200dpi
1bit
PS
600 x 600dpi
1bit, 4bit
1,200 x 1,200dpi
1bit
Monochrome
Color
Scanning
Resolution (dpi)
Resolution (dpi)
Platen
600 x 600dpi
600 x 400dpi
600 x 300dpi (default)
600 x 400dpi
600 x 300dpi (default)
–
DSPF
600 x 600dpi
600 x 400dpi
600 x 300dpi (default)
600 x 400dpi
600 x 300dpi (default)
–
Exposure lamp
White LED
Reading gradation
10bit
Output gradation
BW: Binary (1bit)
Gray scale: 8bit
Full Color: each color RGB 8bit
Gray scale: 8bit
Full Color: each color RGB 8bit
Type
Document table fixed system (Flat bed)
Scanning area
297 x 432mm
Original standard
position
position
Left top reference
Detection
Yes
Detection size
Automatic detection (One type of detection unit to
be switched for software destination)
be switched for software destination)
Dehumidifying
heater (Scanner
section)
heater (Scanner
section)
Supplied as a service parts
Paper
105cpm
machine
120cpm
machine
Click on the first or last page to see other MX-M1055 / MX-M1205 service manuals if exist.