Sharp MX-M1055 / MX-M1205 Service Manual ▷ View online
MX-M1205 ADJUSTMENTS 5 – 61
Operation in monochrome auto copy mode:
When the density of the document of the read area is light, output
image density is increased by control. When the density of the doc-
ument of the read area is dark, output image density is decreased
by control.
When the density of the document of the read area is light, output
image density is increased by control. When the density of the doc-
ument of the read area is dark, output image density is decreased
by control.
11-D
(5)
Document low density image density
reproduction adjustment in the automatic
monochrome (Copy/Scan) mode
(No need to adjust normally) (Background
density adjustment in the scanning section)
Document low density image density
reproduction adjustment in the automatic
monochrome (Copy/Scan) mode
(No need to adjust normally) (Background
density adjustment in the scanning section)
Use for the reproducibility adjustment of document background
density in monochrome auto copy mode.
density in monochrome auto copy mode.
This adjustment is required in the following cases.
* When there is a desire not to reproduce the background of the
document. When there is a desire to reproduce the low density
image of the document.
image of the document.
* When there is request from the user.
1)
Enter the SIM 46-32 mode.
2)
Select the adjustment mode with the scroll key.
3)
Enter the adjustment value with 10-key and press [OK] key.
When the adjustment value is increased, reproducibility of the
background and the low density image is increased. When the
adjustment value is decreased, reproducibility of the back-
ground and the low density image is decreased.
background and the low density image is increased. When the
adjustment value is decreased, reproducibility of the back-
ground and the low density image is decreased.
11-D
(6)
Copy/Scan low density image density
adjustment (for each mode)
(No need to adjust normally)
Copy/Scan low density image density
adjustment (for each mode)
(No need to adjust normally)
This adjustment is used to adjust the image density in the low den-
sity area in the copy/scanner mode.
sity area in the copy/scanner mode.
This adjustment is required in the following cases.
* When there is a desire not to reproduce the background of the
document. When there is a desire to reproduce the low density
image of the document.
image of the document.
* When there is request from the user.
1)
Enter the SIM 46-63 mode.
2)
Select the copy mode to be adjusted with the scroll key.
3 to 7mm
3 to 7mm
100mm
100mm
3 to 7mm
Document table/DSPF mode
Document table mode
DSPF mode
AE WIDTH = FULL
AE WIDTH = PART
AE WIDTH = PART
Document density detection area
Item/Display
Content
Setting
range
Default
value
A
COPY: OC
Copy mode (for OC)
1 - 250
196
B
COPY: DSPF
(SIDE1)
(SIDE1)
Copy mode
(for DSPF front surface)
(for DSPF front surface)
1 - 250
196
C
COPY: DSPF
(SIDE2)
(SIDE2)
Copy mode
(for DSPF back surface)
(for DSPF back surface)
1 - 250
196
D
SCAN: OC
Scanner mode (for OC)
1 - 250
196
E
SCAN: DSPF
(SIDE1)
(SIDE1)
Scanner mode
(for DSPF front surface)
(for DSPF front surface)
1 - 250
196
F
SCAN: DSPF
(SIDE2)
(SIDE2)
Scanner mode
(for DSPF back surface)
(for DSPF back surface)
1 - 250
196
Display/Item
Content
Set
value
Default
A
COLOR PUSH:TEXT/
PRINTED PHOTO
PRINTED PHOTO
Text print
(color PUSH)
(color PUSH)
1 - 9
3
B
COLOR PUSH:TEXT
Text (color PUSH)
1 - 9
3
C
COLOR PUSH:
PRINTED PHOTO
PRINTED PHOTO
Printed photo
(color PUSH)
(color PUSH)
1 - 9
5
D
COLOR PUSH:
PHOTOGRAPH
PHOTOGRAPH
Photograph
(color PUSH)
(color PUSH)
1 - 9
5
E
COLOR PUSH:
TEXT/PHOTO
TEXT/PHOTO
Text/Photograph
(color PUSH)
(color PUSH)
1 - 9
3
F
COLOR PUSH: MAP
Map (color PUSH)
1 - 9
5
MX-M1205 ADJUSTMENTS 5 – 62
3)
Enter the adjustment value with 10-key and press [OK] key.
When the adjustment value is increased, reproducibility of the
background and the low density image is increased. When the
adjustment value is decreased, reproducibility of the back-
ground and the low density image is decreased.
background and the low density image is increased. When the
adjustment value is decreased, reproducibility of the back-
ground and the low density image is decreased.
11-D
(7)
Monochrome (Copy/Scan) mode color
document reproduction adjustment
(No need to adjust normally)
Monochrome (Copy/Scan) mode color
document reproduction adjustment
(No need to adjust normally)
Use to adjust the reproducibility for the red image and the yellow
image when printing color document that included the red/yellow
image in monochrome copy mode.
image when printing color document that included the red/yellow
image in monochrome copy mode.
This adjustment is required in the following cases.
* When there is desire to change reproducibility of yellow/red
image in case of making a color copy of the color document in
monochrome copy mode.
monochrome copy mode.
* When there is request from the user.
1)
Enter the SIM 46-37 mode.
2)
Select the mode to be adjusted with the scroll key.
3)
Enter the adjustment value with 10-key.
When the adjustment value of adjustment item A is increased,
copy density of red image is decreased. When the adjustment
value is decreased, copy density of red image is increased.
copy density of red image is decreased. When the adjustment
value is decreased, copy density of red image is increased.
When the adjustment value of adjustment item B is increased,
copy density of yellow image is decreased. When the adjust-
ment value is decreased, copy density of yellow image is
increased.
copy density of yellow image is decreased. When the adjust-
ment value is decreased, copy density of yellow image is
increased.
4)
Press [OK] key.
5)
Make a copy in monochrome text/printed photo copy mode
(manual), check the copy.
(manual), check the copy.
If a satisfactory result is not obtained, return to the SIM 46-37
mode and change the adjustment value.
mode and change the adjustment value.
Repeat the above procedures until a satisfactory result is
obtained.
obtained.
11-D
(8)
Monochrome copy/color scan mode
sharpness adjustment
(No need to adjust normally)
Monochrome copy/color scan mode
sharpness adjustment
(No need to adjust normally)
Use for sharpness adjustment of the high density image in mono-
chrome copy/color scan mode.
chrome copy/color scan mode.
This adjustment changes smoothness (asperity) in the image
shade part.
shade part.
This adjustment is required in the following cases.
* When changing the sharpness of copy image in copy mode.
(obtain crispy image) (decreases moire)
* When there is desire to improving smoothness in the image
shade part (for decrease of asperity)
* To make the black background and the dark area darker.
* To reproduce the gradation change in the dark area.
* When there is request from the user.
1)
Enter the SIM 46-60 mode.
2)
Select the mode to be adjusted with the scroll key.
3)
Input numeric value corresponding to sharpness level (filter
process mode).
process mode).
• Adjustment item A:
When selecting AUTO, filter is selected according to dot pat-
tern state automatically and adjusts sharpness.
tern state automatically and adjusts sharpness.
Input small numeric value to obtain crispy image. Input large
numeric value to decrease moire.
numeric value to decrease moire.
• Adjustment item B:
Select HIGH to obtain clear images. Select SOFT to reduce
moire.
moire.
• Adjustment item C - J:
When setting ON, smoothness in the image shade part
improves by applying soft filter. (asperity decreases)
improves by applying soft filter. (asperity decreases)
4)
Press [OK] key.
5)
Make a copy and check the copy image.
If a satisfactory result is not obtained, return to the SIM 46-60 mode
and change the adjustment value.
and change the adjustment value.
Repeat the above procedures until a satisfactory result is obtained.
Item/Display
Content
Setting
range
Default
value
A
R-Ratio
Gray making setting (R)
0 - 1000
63
B
G-Ratio
Gray making setting (G)
0 - 1000
847
C
R-Ratio RIP
Print gray making setting (R)
0 - 1000
299
D
G-Ratio RIP
Print gray making setting (G)
0 - 1000
587
B-Ratio
Gray making setting (B) (1000-R-Ratio - G-Ratio)
B-Ratio RIP
Print gray making setting (B)
(1000-R-Ratio RIP - G-Ratio RIP)
(1000-R-Ratio RIP - G-Ratio RIP)
Item/Display
Content
Setting
range
Default
value
A
CPY
PUSH
AUTO
FILTER
LEVEL
PUSH
AUTO
FILTER
LEVEL
SOFT
Sharpness:
The
sharpness is
specified
when the
document
mode is
judged as A5
or A6 by the
auto mode of
PUSH.
The
sharpness is
specified
when the
document
mode is
judged as A5
or A6 by the
auto mode of
PUSH.
SOFT
1 - 3
1
2
(CEN-
TER)
CENTER
CENTER
2
HIGH
HIGH
3
B
B/W
COPY
COPY
OFF
Filter
mixture,
Register
select
pattern,
Monochrome
copy
mixture,
Register
select
pattern,
Monochrome
copy
OFF
0 - 1
0
1(ON)
ON
ON
1
C
COLOR
PUSH:
RGB
PUSH:
RGB
OFF
Filter
mixture,
Register
select
pattern,
Color push
mixture,
Register
select
pattern,
Color push
OFF
0 - 1
0
1(ON)
ON
ON
1
D
B/W
PUSH
PUSH
OFF
Filter
mixture,
Register
select
pattern,
Monochrome
push
mixture,
Register
select
pattern,
Monochrome
push
OFF
0 - 1
0
1(ON)
ON
ON
1
E
B/W
PRINT
OFF
Filter
mixture,
Register
select
pattern,
Monochrome
print
mixture,
Register
select
pattern,
Monochrome
OFF
0 - 1
0
0(OFF)
ON
ON
1
MX-M1205 ADJUSTMENTS 5 – 63
11-D
(9)
Copy high density image density
reproduction setting (Normally
unnecessary to the setting change)
Copy high density image density
reproduction setting (Normally
unnecessary to the setting change)
If a tone gap occurs on part of high density in copy mode, or if there
is necessity to increase the density of the part of high density,
change the setting.
is necessity to increase the density of the part of high density,
change the setting.
This setting is normally not required. When, however, there are
case of following, change the setting.
case of following, change the setting.
* When a tone gap occurs on part of high density.
* When there is a necessity to increase the density of the part of
high density.
* When there is request from the user.
a. Adjustment procedure
1)
Enter the SIM 46-23 mode.
2)
Select the item A, B with the scroll key.
* If a tone gap occurs on part of high density, set 0 to item A and B
The density of high density part decreases. However, the tone
gap is better.
gap is better.
* In case of more increase of the density on high density part, set 1
to item A and B.
The tone gap may occur in high density part.
NOTE: Do not change the setting values of item C, D, E and F. If
these values are changed, density of the high density part
is changed.
is changed.
If these values are changed, be sure to execute the copy
gray balance density adjustment. (Auto adjustment)
gray balance density adjustment. (Auto adjustment)
11-D
(10)
DSPF mode (Copy/Scan) density
adjustment (No need to adjust normally)
DSPF mode (Copy/Scan) density
adjustment (No need to adjust normally)
This setting is normally not required, however, in the following
cases, make changes to the setting:
cases, make changes to the setting:
* When copy in DSPF mode differs from copy in document table
mode.
* When copy density in DSPF mode is low or too high.
* When the DSPF unit is replaced.
* When the DSPF unit is disassembled.
* The CCD unit has been replaced.
* U2 trouble has occurred.
* When the MFP PWB is replaced.
* When the EEPROM on the MFP PWB is replaced.
a. Adjustment procedure
1)
Enter the SIM 46-9 mode.
2)
Select the mode to be adjusted with the scroll key.
When adjusting density on low density part, select "A (COPY
SIDEA:LOW)". When adjusting density on high density part,
select "D (COPY SIDEA:HIGH)".
SIDEA:LOW)". When adjusting density on high density part,
select "D (COPY SIDEA:HIGH)".
3)
Enter the adjustment value with 10-key.
In case of increase of image density, input large numeric
value. Or in case of diluting the image density, input small
numeric value.
value. Or in case of diluting the image density, input small
numeric value.
4)
Press [OK] key.
5)
Make a copy in the DSPF mode and check the copy.
If a satisfactory result is not obtained, return to the SIM 46-9 mode
and change the adjustment value.
and change the adjustment value.
Repeat the above procedures until a satisfactory result is obtained.
Item
Display
Content
Setting
range
Default
value
A
K
(0:ENABLE
1:DISABLE)
(0:ENABLE
1:DISABLE)
0
K engine highest density
correction mode: Enable
correction mode: Enable
0 - 1
1
1
K engine highest density
correction mode: Disable
correction mode: Disable
B
BLACK MAX
TARGET
TARGET
Scanner target value for
BLACK max. density
correction
BLACK max. density
correction
0 - 999
500
Item
Button
Display
Content
Setting
range
Default
value
A
OC
COPY
SIDEA:
LOW
SIDEA:
LOW
DSPF copy mode
exposure adjustment
(Low density side)
exposure adjustment
(Low density side)
1 - 99
47
B
SCAN
SIDEA:
LOW
SIDEA:
LOW
DSPF scanner mode
exposure adjustment
(Low density side)
exposure adjustment
(Low density side)
1 - 99
47
C
COPY
SIDEA:
HIGH
SIDEA:
HIGH
DSPF copy mode
exposure adjustment
(High density side)
exposure adjustment
(High density side)
1 - 99
52
D
SCAN
SIDEA:
HIGH
SIDEA:
HIGH
DSPF scanner mode
exposure adjustment
(High density side)
exposure adjustment
(High density side)
1 - 99
52
A
DSPF
COPY
SIDEB:
LOW
SIDEB:
LOW
DSPF copy mode
exposure adjustment
(Low density side)
exposure adjustment
(Low density side)
1 - 99
47
B
SCAN
SIDEB:
LOW
SIDEB:
LOW
DSPF scanner mode
exposure adjustment
(Low density side)
exposure adjustment
(Low density side)
1 - 99
47
C
COPY
SIDEB:
HIGH
SIDEB:
HIGH
DSPF copy mode
exposure adjustment
(High density side)
exposure adjustment
(High density side)
1 - 99
50
D
SCAN
SIDEB:
HIGH
SIDEB:
HIGH
DSPF scanner mode
exposure adjustment
(High density side)
exposure adjustment
(High density side)
1 - 99
50
E
BALANCE
SIDEB: R
SIDEB: R
DSPF gray balance
R
R
1 - 99
50
F
BALANCE
SIDEB: G
SIDEB: G
DSPF gray balance
G
G
1 - 99
50
G
BALANCE
SIDEB: B
SIDEB: B
DSPF gray balance
B
B
1 - 99
50
MX-M1205 ADJUSTMENTS 5 – 64
11-D
(11)
Automatic gray balance adjustment by the
user (Copy gray balance automatic
adjustment ENABLE setting and
adjustment)
Automatic gray balance adjustment by the
user (Copy gray balance automatic
adjustment ENABLE setting and
adjustment)
a. General
In the user program mode, the user can execute the auto gray cali-
bration (auto adjustment of the copy gray balance and density).
bration (auto adjustment of the copy gray balance and density).
This adjustment is to set Enable/Disable of the above user opera-
tion with SIM 26-53.
tion with SIM 26-53.
NOTE: This setting must be set to ENABLE only when the user's
understanding on the automatic adjustment of the copy
gray balance and density and the user's operational ability
are judged adequate enough to execute the adjustment.
gray balance and density and the user's operational ability
are judged adequate enough to execute the adjustment.
When set to enable, operation procedures must be fully
explained to the user.
explained to the user.
b. Setting procedure
1)
Enter the SIM 26-53 mode.
2)
Select ENABLE or DISABLE with 10-key.
When disabling, set to "0" (NO). When enabling, set to "1"
(Yes).
(Yes).
3)
Press [OK] key.
When set to DISABLE, the menu of the user auto gray calibration
(automatic adjustment of copy gray balance and density) is not dis-
played in the user program mode.
(automatic adjustment of copy gray balance and density) is not dis-
played in the user program mode.
(Auto color calibration by the user (Auto gray balance adjust-
ment))
ment))
NOTE: This adjustment is based on the service target gray bal-
ance set with SIM 63-7 and SIM 63-8. If, therefore, the
above settings are not properly performed, this adjustment
cannot be made properly.
above settings are not properly performed, this adjustment
cannot be made properly.
1)
Enter the system setting mode.
2)
Enter the copy setting mode.
3)
Press the auto gray calibration key.
4)
Press [EXECUTE] key.
The gray patch image (adjustment pattern) is printed out.
5)
Set the gray patch image (adjustment pattern) printed in proce-
dure 4) on the document table.
dure 4) on the document table.
Set the patch image so that the thin line is on the left side as
shown in the figure.
shown in the figure.
At that time, place 5 sheets of white paper on the above gray
patch image (adjustment pattern).
patch image (adjustment pattern).
6)
Press [EXECUTE] key, and the copy gray balance adjustment
is executed automatically. After completion of the adjustment,
the display returns to the original operation screen.
is executed automatically. After completion of the adjustment,
the display returns to the original operation screen.
The message, "Will you go on to the printer gray balance
adjustment?" is displayed.
adjustment?" is displayed.
To execute the printer gray balance adjustment successively,
perform the procedures same as the above.
perform the procedures same as the above.
11-D
(12)
Copy gamma, gray balance adjustment for
each dither (Automatic adjustment)
Copy gamma, gray balance adjustment for
each dither (Automatic adjustment)
a. General
This simulation is used to improve the image quality in a certain
mode. (Refer to the list in procedure 6.)
mode. (Refer to the list in procedure 6.)
b. Adjustment procedures
1)
Enter the SIM46-54 mode.
2)
Press [EXECUTE] key.
A4/11" x 8.5" or A3/11" x 17" paper is automatically selected.
The gray patch image (adjustment pattern) is printed.
The gray patch image (adjustment pattern) is printed.
3)
Set the patch image (adjustment pattern) printed in the proce-
dure 2) on the document table so that the thin lines on the
printed patch image (adjustment pattern) are on the left side.
Place 5 sheets of white paper on the printed patch image
(adjustment pattern).
dure 2) on the document table so that the thin lines on the
printed patch image (adjustment pattern) are on the left side.
Place 5 sheets of white paper on the printed patch image
(adjustment pattern).
Click on the first or last page to see other MX-M1055 / MX-M1205 service manuals if exist.