DOWNLOAD Sharp MX-LC13 (serv.man22) Service Manual ↓ Size: 8.61 MB | Pages: 43 in PDF or view online for FREE

MX-LC13  DISASSEMBLY AND ASSEMBLY  6 - 2

1)

Remove the upper cabinet left.

2)

Open the left door.

3)

Remove the resin E-ring, and remove the shaft. Remove the
left door.

1)

Remove the rear cabinet.

2)

Remove the screw, and remove the left rear cabinet

1)

Remove the right cabinet.

2)

While releasing lock of the paper feed tray bottom, pull out the
paper feed tray.

3)

Remove the screws at the back side of the paper feed tray,
and remove the binding band and the earth wire. 
Disconnect the connector.

1

Paper feed tray

2

Paper feed unit

3

Paper feed belt

4

Paper feed duct unit

1

1
2

2

3

: ‘14/Jul

MX-LC13  DISASSEMBLY AND ASSEMBLY  6 - 3

4)

Remove the screws at the both sides of the paper feed tray,
and remove the paper feed tray from the slide rail.

1)

Remove the screws of the rear cabinet, and remove the cover.
Disconnect the connector from the paper feed unit.

2)

While releasing lock of the paper feed tray bottom, pull out the
paper feed tray.

3)

Remove the screw, and remove the paper feed unit.

1)

Remove two screws from the suction duct front frame/top side
of the Unit.

2)

Turn the unit over and remove two screws from the blower
duct; rear side/bottom of the unit.

3)

Disconnect 3 connectors and remove the band.

: ‘14/Jul

MX-LC13  DISASSEMBLY AND ASSEMBLY  6 - 4

5)

Remove 3 screws 2 ground screws and ground plate from the 
mounting plate.                                                                                

*When installing the unit, make sure not to drop and lose the 
grounding plate. Put it aside for later installation.

6)

 Before moving the Follower roller shaft, make sure that you
pull the solenoid arm out of the slot.

7)

Lift and move the follower roller shaft to the center of the unit to
release the tension on the belt. And then remove the E-clips of
the both side of the follower shaft..   

8)

Remove the bearings of the both side and remove the follower
roller shaft out of the slot to allow the belt to slide out.

9)

Slide the belts out one by one.

NOTE: Replace all four belts at the same time. 

NOTE:  Replace them with new ones one at a time without

damaging the belts.

NOTE: Insert the belt to the position A and slide it to the allow

B direction as the photo below.

NOTE: Never stretch it out too much to prevent the belt trans-

formation.

NOTE: Never insert the belts horizontally by force, in order not

to transform the belts. 

1)

Remove the rear cabinet.

2)

Disconnect the connector of the fan and clutch. Remove the
screw, and remove the binding band.

3)

Remove the screw, and remove the paper feed duct unit.

)VLGH

5VLGH

3DSHU)HHGXQLW

$

%

8QLW)6LGH

8QLW)6LGH

: ‘14/Jul

MX-LC13  DISASSEMBLY AND ASSEMBLY  6 - 5

1)

Remove the rear cabinet.

2)

Remove the left door.

3)

Remove the left rear cabinet.

4)

Remove the paper feed tray.

5)

Remove the paper feed unit.

6)

Remove the E-ring, and remove the knob. Remove the screws
and remove the inside cabinet left upper.

7)

Remove the E-ring, and remove the knob. Remove the screws
and remove the inside cabinet left lower.

8)

Disconnect the connector of the switch and sensor. Remove
the screw, and remove the connection unit. Remove the snap
band, and disconnect the connector of the connection unit.

9)

Remove the screw, and remove the handle.

10) Disconnect the connector of the vertical transport unit.

11) Remove the screws fixing the vertical transport unit.

1

Vertical transport unit

1