Sharp MX-LC13 (serv.man2) Service Manual ▷ View online
MX-LC13 DISASSEMBLY AND ASSEMBLY 6 - 2
(4)
Left door
1)
Remove the upper cabinet left.
2)
Open the left door.
3)
Remove the resin E-ring, and remove the shaft. Remove the
left door.
left door.
(5)
Left rear cabinet
1)
Remove the rear cabinet.
2)
Remove the screw, and remove the left rear cabinet
B. Paper feed section
(1)
Paper feed tray
1)
Remove the right cabinet.
2)
While releasing lock of the paper feed tray bottom, pull out the
paper feed tray.
paper feed tray.
3)
Remove the screws at the back side of the paper feed tray,
and remove the binding band and the earth wire.
Disconnect the connector.
and remove the binding band and the earth wire.
Disconnect the connector.
3
1
2
1
1
2
1
No.
Unit name
1
Paper feed tray
2
Paper feed unit
3
Paper feed belt
4
Paper feed duct unit
1
1
2
2
2
3
1
2
2
1
1
3
2
4
2
: ‘14/Jul
2
MX-LC13 DISASSEMBLY AND ASSEMBLY 6 - 3
4)
Remove the screws at the both sides of the paper feed tray,
and remove the paper feed tray from the slide rail.
and remove the paper feed tray from the slide rail.
(2)
Paper feed unit
1)
Remove the screws of the rear cabinet, and remove the cover.
Disconnect the connector from the paper feed unit.
Disconnect the connector from the paper feed unit.
2)
While releasing lock of the paper feed tray bottom, pull out the
paper feed tray.
paper feed tray.
3)
Remove the screw, and remove the paper feed unit.
(3)
Paper feed belt
1)
Remove two screws from the suction duct front frame/top side
of the Unit.
of the Unit.
2)
Turn the unit over and remove two screws from the blower
duct; rear side/bottom of the unit.
duct; rear side/bottom of the unit.
3)
Disconnect 3 connectors and remove the band.
1
1
1
2
1
1
2
1
2
3
3
1
2
2
1
2
2
: ‘14/Jul
2
MX-LC13 DISASSEMBLY AND ASSEMBLY 6 - 4
5)
Remove 3 screws 2 ground screws and ground plate from the
mounting plate.
mounting plate.
*When installing the unit, make sure not to drop and lose the
grounding plate. Put it aside for later installation.
grounding plate. Put it aside for later installation.
6)
Before moving the Follower roller shaft, make sure that you
pull the solenoid arm out of the slot.
pull the solenoid arm out of the slot.
7)
Lift and move the follower roller shaft to the center of the unit to
release the tension on the belt. And then remove the E-clips of
the both side of the follower shaft..
release the tension on the belt. And then remove the E-clips of
the both side of the follower shaft..
8)
Remove the bearings of the both side and remove the follower
roller shaft out of the slot to allow the belt to slide out.
roller shaft out of the slot to allow the belt to slide out.
9)
Slide the belts out one by one.
NOTE: Replace all four belts at the same time.
NOTE: Replace them with new ones one at a time without
damaging the belts.
NOTE: Insert the belt to the position A and slide it to the allow
B direction as the photo below.
NOTE: Never stretch it out too much to prevent the belt trans-
formation.
NOTE: Never insert the belts horizontally by force, in order not
to transform the belts.
(4)
Paper feed duct unit
1)
Remove the rear cabinet.
2)
Disconnect the connector of the fan and clutch. Remove the
screw, and remove the binding band.
screw, and remove the binding band.
3)
Remove the screw, and remove the paper feed duct unit.
)VLGH
5VLGH
3DSHU)HHGXQLW
$
%
8QLW)6LGH
8QLW)6LGH
2
1
1
1
1
3
1
1
2
1
1
1
1
1
1
2
: ‘14/Jul
2
2
MX-LC13 DISASSEMBLY AND ASSEMBLY 6 - 5
C. Transport section
(1)
Vertical transport unit
1)
Remove the rear cabinet.
2)
Remove the left door.
3)
Remove the left rear cabinet.
4)
Remove the paper feed tray.
5)
Remove the paper feed unit.
6)
Remove the E-ring, and remove the knob. Remove the screws
and remove the inside cabinet left upper.
and remove the inside cabinet left upper.
7)
Remove the E-ring, and remove the knob. Remove the screws
and remove the inside cabinet left lower.
and remove the inside cabinet left lower.
8)
Disconnect the connector of the switch and sensor. Remove
the screw, and remove the connection unit. Remove the snap
band, and disconnect the connector of the connection unit.
the screw, and remove the connection unit. Remove the snap
band, and disconnect the connector of the connection unit.
9)
Remove the screw, and remove the handle.
10) Disconnect the connector of the vertical transport unit.
11) Remove the screws fixing the vertical transport unit.
No.
Unit name
1
Vertical transport unit
1
3
3
3
4
1
2
3
3
3
4
1
2
1
1
2
2
2
2
3
4
5
1
2
Click on the first or last page to see other MX-LC13 (serv.man2) service manuals if exist.