DOWNLOAD Sharp MX-LC13 (serv.man15) Service Manual ↓ Size: 11.35 MB | Pages: 68 in PDF or view online for FREE

MX-7500N  MX-LC13 (LARGE CAPACITY TRAYS)  9 – 10

5) Connect the connector from LCT to the paper pass unit and

tighten the screw.

1) Connect the power plug of the machine to the power outlet,

and turn ON the main power switch and the operation panel
power switch.

1) Check to insure that the main body is standby state, and press

the [System setting] key on the operation panel.

2) Menu screen is displayed on the touch panel. Select the

[Paper Tray Settings].

3) Select the paper size of large capacity tray from contents of

[Paper Tray Settings].

CAUTION: If the off-center adjustment is not completely, there's a

possibility to have the following problem when large size
paper (example: 13 * 19 inch size) was fed from LCT.
A: Registration Shift
B: Mechanical Vignetting

If the center is shifted greatly, “Color Shift” or Mechanical Vignett-
ing” may occur as the figure above.
In this case, it is necessary to do the following mechanical adjust-
ment.
Normally, Off-center adjustment is done by image processing using
CIS function. To check the mechanical off-center position, CIS
function needs to be turned off. 
1) Run Sim50-10 using the keypad on the main unit.
2) Select SW1 and change the value “1” to “0”.
3) Press [EXECUTE] key to print out for each paper feed tray.

4)

Check the void area of the adjustment pattern and check the
“Off-center” shift amount (A-B).
“A-B” is over 3mm: Move to Mechanical Adjustment 1
“A-B” is less than +/-3mm: Move to Mechanical Adjustment 2
“A-B” is less than +/-2mm: SW1 “0” to “1” for auto adjustment.

If “Off-center” is over +/-3mm.
1)

Open the left side door and the LCT delivery paper guide unit.

2)

Loosen the 2 blue screws.

A: Registration Shift

B: Mechanical Vignetting

!

"

3ULQWHGVXUIDFH

3DSHUGHOLYHU\
GLUHFWLRQ

,IWKHGLPHQVLRQRI%LVELJ͆2IIFHQWHU͇
VKLIWGLUHFWLRQLVUHDUGLUHFWLRQ

,IWKHGLPHQVLRQRI$LVELJ͆2IIFHQWHU͇
VKLIWGLUHFWLRQLVIURQWGLUHFWLRQ

5HDU6LGH

)URQW6LGH

$%
PP0HFKDQLFDODGMXVWPHQWPP0HFKDQLFDODGMXVWPHQW

MX-7500N  MX-LC13 (LARGE CAPACITY TRAYS)  9 – 11

3) Adjust the LCT position to push or pull with holding the pillar of

LCT as the figure below.
In case the print image shifts to front: Push LCT to rear
direction.
In case the print image shifts to rear: Pull LCT to front direc-
tion.
After finish the adjustment, fix the unit with the 2 blue screws.

If these adjustment above couldn’t adjust Off-center completely, the
following adjustment is needed.
When shifting the line of printing from the center of the paper in the
direction A of arrow as shown below:
1) Separate the LCT from MX-RB14.

When separating, tighten the screw to release the lock. 
When connecting again, loosen the screw after connection.

2) Open the left side door and open the LCT delivery paper guide

unit.

3) Loosen the 2 blue screws.
4) Shift the connection unit to the following direction and fix the 2

blue screws.

In case the print image shifts to front;
- Shift the Connection plate unit to the front.
In case the print image shifts to rear: Use F hole.
- Shift the Connection plate unit to the rear.

5)

To stick the L-shape driver (Packed items No.12) to the adjust-
ment hole, the connection plate unit position can be adjusted
to the following 4 steps.
F1.5 / 3 : Shift the unit 3 / 1.5 mm to front.
R1.5 / 3 : Shift the unit 3 / 1.5 mm to rear.

6)

Reinstall LCT to MX-RB14. 
Use the mark of the rear regulation plate, and fix the blue
screw at the position so that the clearance between paper and
the rear regulation plate is evenly 1mm.
NOTE: Fasten the screw which was unfastened in the proceu-
dre 1).

When shifted over +/-2mm less than +/-3mm.
1)

Pull out the cassette.
Press the lock button on the front cabinet and lower the paper
feed base tray to the paper supply position. Pull out the tray.
* In case the machine is turned off, If it is necessary to release
the lock manually, push the shaft at the bottom of the front cab-
inet and lower the paper feed base tray to the paper supply
position and pull out the tray. 

When shifting the line of printing from the center of the paper in
the direction A of arrow as shown below:

&RQQHFWLRQSODWHXQLW

5

)

5

)

MX-7500N  MX-LC13 (LARGE CAPACITY TRAYS)  9 – 12

2) Loosen the blue screws of the rear regulation plate, and move

the plate with referring the carved marks by the dimension
shifted in the direction A (R side), and tighten the blue screws.

3) Set a sheet of paper on the paper feed base tray and loosen

the blue screws of the front regulation plate.
Move the front regulation plate to the direction A (R side) with
pushing paper to the front regulation plate.

4) Set the front regulation plate to make gap between the rear

regulation plate and paperand tighten the blue screws of the
fron regulation plate.

NOTE: Avoid bending paper with too much closing the regulation

plates.

NOTE: When shifting the line of printing from the center of the

paper to rear side, move the front regulation plate to adjust
it.

1)

Pull out the cassette.
Press the lock button on the front cabinet and lower the paper
feed base tray to the paper supply position. Pull out the tray.
* In case the machine is turned off, If it is necessary to release
the lock manually, push the shaft at the bottom of the front cab-
inet and lower the paper feed base tray to the paper supply
position and pull out the tray. 

2)

Adjust the diagonal feed.

3)

Set a sheet of paper on the paper feed base tray and adjust
the width of the regulation plate.
In the case of diagonal feed 1
Loosen the 2 blue screw (1) on the front regulation plate.
Referring to the degree of diagonal feed, move the regulation
plate in the clockwize direction and fix the blue screw.

Loosen the 2 blue screws (2) on the rear regulation plate.
To make parallel with the front regulation plate, move the rear
regulation plate in the clockwize direction and fix the screws.

5HDU

%OXH6FUHZV

5HJXODWLRQ3ODWH

)URQW

3DSHU

3XVKSDSHUWRWKHIURQW
UHJXODWLRQSODWH

MM

3DSHU

Diagonal feed 1

Diagonal feed 2

Transport 
direction

)URQW

3DSHU

5HDU

5HJXODWLRQ3ODWH

TopPage

: ‘14/Jan

MX-7500N  MX-LC13 (LARGE CAPACITY TRAYS)  9 – 13

In the case of diagonal feed 2
Loosen the 2 blue screws (1) on the front regulation plate.
Referring to the degree of diagonal feed, move the regulation
plate in the counterclockwize direction and fix the blue screw.

Loosen the 2 blue screws (2) on the rear regulation plate.
To make parallel with the front regulation plate, move the rear
regulation plate in the counterclockwize direction and fix the
screws.

NOTE: When fixing the rear regulation plate, not to fix it more

closely against the paper.
(The target of the gap between the edge of paper and the
rear regulation plate is about 1.0mm)

NOTE: After completion of the adjustment, check that the front reg-

ulation plate and the rear regulation plate are in parallel to
each other.

In order to avoid the unstable installation, underlay the adjustment
bolt with the adjuster and fix LC13 to the floor.

NOTE: Fix the right side adjuster not to change the height level of

LC13 largely.

NOTE: If the fixation of LC13 is unstable, it might be moved when

insert the tray to the unit.

1)

If there’s some gap between cabinets or door adjustment is neces-
sary, adjust the height adjustment.
1)

Install the adjuster (Packed items No.3) and adjuste the height
of LC13 (4 places)

2)

Adjust height in order to make the gap evenly of  each cabinet
as the figure below.

3)

Adjust height in order to make the height and the gap evenly of
each cabinet as the figure below.

Though the off-center adjustment has been made by CIS function,
if the fine adjustment is necessary, perform the following adjust-
ment.
1)

Run Sim50-10 using the keypad on the main unit.

2)

On the touch panel, press [DOWN] Key to select "H: 50:
MAINLCT1."

3)

Enter the desired adjustment value through the numeric key-
pad. (This value, which defaults to 50, can be adjusted within
the range of 1 to 99)

4)

After entering the adjustment value, press the [EXECUTE] key
on the touch panel to start printing and save the setting.

-    Reducing the adjustment value by 1 causes the main scan/

print position to shift by 0.1mm toward the rear.

-    Increasing the adjustment value by 1 causes the main scan/

print position to shift by 0.1mm toward the front.

)URQW

3DSHU

5HDU

5HJXODWLRQ3ODWH

TopPage

: ‘14/Jan